Acclaim Lighting 2490 Above a Fireplace, Through a Fireplace, Wall Pass-Throughs

Page 7

A special piece called the “thimble sleeve,” slightly smaller in diameter than standard connector and most thimbles, will facilitate the removal of the chimney connector system for inspection and cleaning. Thimble sleeves should be available from your local dealer.

To install a thimble sleeve, slide it into the breech until it is flush with the inner flue wall. Do not extend it into the actual flue passage, as this could interfere with the draft.

The thimble sleeve should protrude 1-2” (25-50mm) into the room. Use furnace cement and thin gasketing to seal the sleeve in place in the thimble. Secure the chim- ney connector to the outer end of the sleeve with sheet metal screws.

Above A Fireplace

In this installation, the chimney connector rises from the stove, turns ninety degrees, and goes back into the fireplace chimney. (Fig. 7) The liner of the fireplace chimney should extend at least to the point at which the chimney connector enters the chimney. Follow all the guidelines for installing a chimney connector into a free- standing masonry chimney, and pay special attention to these additional points:

•If there is a combustible mantel or trim, check the stove and chimney connector clearances. Use the necessary combination of mantel, trim, and connec- tor heat shields to provide the required clearances.

•Double-check connector clearance from the ceiling.

•The fireplace damper must be closed and sealed to prevent room air from being drawn up the flue, reducing the draft. However, it must be possible to reopen the damper to inspect or clean the chimney.

Chimney Con-

 

nector Shields

*

 

* Check these

*

clearances

 

Mantel

 

Seal the

Acclaim

Damper

R E S O L U T E

 

ST244

Fig. 7 Chimney connector enters chimney above the fireplace.

Resolute® Acclaim Woodburning Stove

Through A Fireplace

If your fireplace opening height is at least 23” (584 mm)*, you may install a Resolute Acclaim through the open- ing using a “positive connection” kit available from your local dealer. These kits provide a secure connection between the stove flue collar and the chimney flue. (Fig.

8)If it is necessary to reverse the flue collar from the

top exit to the rear exit position, follow the directions on Page 10.

Fireplace installations, whether connected to the flue above or through the fireplace opening, have special clearance requirements to adjacent trim and the mantel. You’ll find the required safe clearances for Resolute Ac- claim fireplace installations on Page 11.

Floor protection requirements also apply to fireplace installations. Floor protection is discussed on Page 9.

Flexible Con-

nector

Mantel Shield

Fireplace

Adpator Kit

R E S O L U T E

Acclaim

ST245

Fig. 8 Chimney connector enters chimney through the fire- place opening.

Wall Pass-Throughs

Whenever possible, design your installation so the con- nector does not pass through a combustible wall. If you are considering a wall pass-through in your installation, check with your building inspector before you begin.

Also check with the chimney connector manufacturer for any specific requirements.

2000893

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Resolute Acclaim Accessories Table of ContentsIntroduction Resolute Acclaim Model SpecificationsWhat Kind of Chimney to Use InstallationMasonry Chimneys Chimney Size Chimney Connector GuidelinesDouble-wall Chimney Connectors Prefabricated ChimneysSecuring the Single-wall Connector To a Masonry Chimney Single-wall Chimney ConnectorsFreestanding Installations Through a Fireplace Above a FireplaceWall Pass-Throughs An approved wall pass-through for the United States Floor Protection Floor Protection for Fireplace InstallationReversing the Flue Collar Keep the Stove a Safe Distance From Surrounding MaterialsSafe Ways to Reduce Clearances Wall Shields6mm Fireplace InstallationsFront Clearance To Combustibles Resolute Acclaim Clearance ChartParallel Installation Corner Stove Clearance Chimney Connector ClearanceTop Exit, No Heat Shields Stove Installed Stove in Corner Parallel to WallMinimum Wall Shield Requirements for Common Installations Corner Parallel Installations Construction Requirements Alcove InstallationsTwo Controls Operate the Stove Install Stove LegsOperation Unpack the StoveBurn Only High-Quality Fuel Use the Air Control Settings That Work Best for YouRemovable Andirons For Greater Front-Loading Convenience Two Rules For SuccessStarting and Maintaining a Wood Fire Primary Air SettingsHow to Build and Sustain a Wood Fire Air Setting Air Control PositionSurface Thermometer is a Guide to Performance Reloading and Reviving a Wood FireClear the Ash Frequently Rules for Open Fire ViewingRemove and Store Ash Safely Draft Management Back-puffing Draft TestingCreosote FuelCare of the Cast Iron Surface MaintenanceCleaning the Glass Clean the Exhaust ChannelsAvoid Damaging the Glass Adjust the DoorAdjust the Damper as Needed Repair Missing Cement in SeamsReplace Broken Glass Immediately How to Replace GasketsResolute Acclaim Gaskets on Moving Parts Replace Broken Firebricks Gaskets on Resolute Acclaim Stationary PartsReplacing the Door Gaskets Replacing the Griddle GasketTwo Months Resolute Acclaim Maintenance ScheduleYearly Spring Cleaning DailyItem Description Part Number Resolute Acclaim Woodburning StoveAshlip Door Leg Resolute Acclaim Woodburning StoveWarranty Mhsc

2490 specifications

Acclaim Lighting has made a significant impact in the world of architectural and entertainment lighting with innovative solutions that cater to a wide array of applications. One of their standout products is the Acclaim Lighting 2490, a lighting fixture that exemplifies cutting-edge technology and high performance.

The Acclaim Lighting 2490 is primarily designed for use in both indoor and outdoor settings. Its robust construction ensures durability against various weather conditions, making it an ideal choice for architectural lighting, theatrical productions, and even large-scale events. One of the standout features of the 2490 is its high lumen output, allowing it to provide bright, effective illumination in any scenario.

Equipped with advanced LED technology, the 2490 offers exceptional energy efficiency without compromising brightness. The fixture utilizes high-quality LEDs that not only extend the lifespan of the unit but also minimize heat generation, making it a sustainable choice for long-term use. This energy-efficient operation translates to lower energy costs and reduced environmental impact.

The Acclaim Lighting 2490 boasts versatile color rendering, with RGBW capabilities that allow users to create a wide palette of colors. This feature is particularly beneficial for event lighting and architectural applications where mood and aesthetics play a crucial role. Additionally, the fixture supports DMX control, making it easy to integrate into existing lighting setups and enabling synchronized light shows or dynamic lighting transitions.

Another noteworthy characteristic of the 2490 is its adjustable beam angle. This adaptability provides users with the flexibility to focus light where it's needed most, whether for highlighting architectural features or creating immersive environments for theatrical performances.

Built with user-friendliness in mind, the Acclaim Lighting 2490 includes options for easy mounting and installation. Its lightweight design coupled with intuitive controls ensures that both professional lighting technicians and newcomers can operate it with ease.

Overall, the Acclaim Lighting 2490 stands as a testament to the brand's commitment to quality and innovation in lighting technology. With its combination of efficiency, versatility, and durability, it offers a comprehensive solution for a wide array of lighting needs, making it a preferred choice among lighting designers and professionals alike.
Top Page Image Contents