Acclaim Lighting 2490 installation instructions Reloading and Reviving a Wood Fire

Page 20

Resolute® Acclaim Woodburning Stove

Damper Control

Closed

Open

 

ST614

Fig. 30 With the damper closed, secondary combustion takes place and the Acclaim operates most efficiently.

minutes at this maximum air setting to guarantee the new load of fuel has fully ignited. Once the fuel is burn- ing steadily, you may adjust the primary air supply to provide the desired heat output.

You’ll soon find this stove is HOT WHILE IN OPERA-

TION! KEEP CHILDREN, CLOTHING, AND FURNI- TURE AWAY. CONTACT MAY CAUSE SKIN BURNS.

DO NOT OVERFIRE THIS HEATER. Overfiring can result in permanent damage to the stove. If an exterior part of the stove or the chimney connector glows, you are overfiring.

Reloading and Reviving a Wood Fire

Reload your stove while it is still hot and there are plenty of embers to re-kindle the fire quickly. Include some smaller pieces of wood in the new load of fuel to help the stove regain high temperatures quickly.

Follow this procedure when you reload your stove:

•Open the damper and move the primary air lever to the “HIGH” position.

•Open the front door and check the ash level on the grates and in the ash pan. Clear excess ash from the grates, particularly at the rear area. Level the ember bed. Empty the ash pan if necessary.

•Replace the ash pan and close the front door.

•Load wood, smaller pieces first, and close the load- ing door.

NOTE: If the ember bed has burned down to the extent the fire cannot be revived easily, it may be necessary to set the air control to the “Start-up” position until the fire has been re-established.

•Allow the stove to regain its “thermal momentum” before closing the damper. This may take 15 - 20 minutes, and will be confirmed by a temperature on the griddle of at least 500°F (260°C).

•Close the damper, and set the primary air lever for the desired heat output.

NOTE: If the remaining charcoal bed is relatively thick and if your fuel is well seasoned, it is possible to add fresh fuel (smaller pieces first), close the door and damper, and reset the primary air within 5 minutes.

A Surface Thermometer is a

Guide to Performance

Until you are familiar with how your stove works, moni- tor the griddle surface temperature frequently. Use these temperature ranges as general indicators of heat output:

Low to medium

350-500°F (177-260°C)

Medium

500-600°F (260-318°C)

High

600-750°F (318-399°C)

Continuous operation at griddle temperatures higher than 750°F (399°C) may damage the cast iron parts or the porcelain enamel finish of your Resolute Acclaim.

A surface thermometer can also tell you when to adjust the controls and when to refuel the stove. (Fig. 31)

During start-up and after re-loading, for example, a thermometer reading of at least 500°F (260°C) signals the stove is hot enough to close the damper and shift into the high-efficiency mode.

Readings lower than 350°F (177°C) announce the stove needs loading or it is time to increase the air sup- ply for a higher burn rate.

At the other exteme, a temperature over 750°F (399°C) is a warning to slow the burn rate.

Stovetop Thermometer

ST615

Fig. 31 A thermometer gives temperature readings that help you to operate your stove safely and effectively.

20

2000893

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Resolute Acclaim Introduction Table of ContentsAccessories Specifications Resolute Acclaim ModelMasonry Chimneys InstallationWhat Kind of Chimney to Use Chimney Connector Guidelines Double-wall Chimney ConnectorsPrefabricated Chimneys Chimney SizeFreestanding Installations Single-wall Chimney ConnectorsSecuring the Single-wall Connector To a Masonry Chimney Wall Pass-Throughs Above a FireplaceThrough a Fireplace An approved wall pass-through for the United States Floor Protection for Fireplace Installation Floor ProtectionKeep the Stove a Safe Distance From Surrounding Materials Safe Ways to Reduce ClearancesWall Shields Reversing the Flue CollarFireplace Installations 6mmResolute Acclaim Clearance Chart Parallel Installation Corner Stove ClearanceChimney Connector Clearance Front Clearance To CombustiblesStove Installed Stove in Corner Parallel to Wall Top Exit, No Heat ShieldsMinimum Wall Shield Requirements for Common Installations Corner Parallel Installations Alcove Installations Construction RequirementsInstall Stove Legs OperationUnpack the Stove Two Controls Operate the StoveUse the Air Control Settings That Work Best for You Removable Andirons For Greater Front-Loading ConvenienceTwo Rules For Success Burn Only High-Quality FuelPrimary Air Settings How to Build and Sustain a Wood FireAir Setting Air Control Position Starting and Maintaining a Wood FireReloading and Reviving a Wood Fire Surface Thermometer is a Guide to PerformanceRemove and Store Ash Safely Rules for Open Fire ViewingClear the Ash Frequently Draft Management Draft Testing CreosoteFuel Back-puffingMaintenance Cleaning the GlassClean the Exhaust Channels Care of the Cast Iron SurfaceAdjust the Door Adjust the Damper as NeededRepair Missing Cement in Seams Avoid Damaging the GlassResolute Acclaim Gaskets on Moving Parts How to Replace GasketsReplace Broken Glass Immediately Gaskets on Resolute Acclaim Stationary Parts Replacing the Door GasketsReplacing the Griddle Gasket Replace Broken FirebricksResolute Acclaim Maintenance Schedule Yearly Spring CleaningDaily Two MonthsResolute Acclaim Woodburning Stove Item Description Part NumberResolute Acclaim Woodburning Stove Ashlip Door LegWarranty Mhsc

2490 specifications

Acclaim Lighting has made a significant impact in the world of architectural and entertainment lighting with innovative solutions that cater to a wide array of applications. One of their standout products is the Acclaim Lighting 2490, a lighting fixture that exemplifies cutting-edge technology and high performance.

The Acclaim Lighting 2490 is primarily designed for use in both indoor and outdoor settings. Its robust construction ensures durability against various weather conditions, making it an ideal choice for architectural lighting, theatrical productions, and even large-scale events. One of the standout features of the 2490 is its high lumen output, allowing it to provide bright, effective illumination in any scenario.

Equipped with advanced LED technology, the 2490 offers exceptional energy efficiency without compromising brightness. The fixture utilizes high-quality LEDs that not only extend the lifespan of the unit but also minimize heat generation, making it a sustainable choice for long-term use. This energy-efficient operation translates to lower energy costs and reduced environmental impact.

The Acclaim Lighting 2490 boasts versatile color rendering, with RGBW capabilities that allow users to create a wide palette of colors. This feature is particularly beneficial for event lighting and architectural applications where mood and aesthetics play a crucial role. Additionally, the fixture supports DMX control, making it easy to integrate into existing lighting setups and enabling synchronized light shows or dynamic lighting transitions.

Another noteworthy characteristic of the 2490 is its adjustable beam angle. This adaptability provides users with the flexibility to focus light where it's needed most, whether for highlighting architectural features or creating immersive environments for theatrical performances.

Built with user-friendliness in mind, the Acclaim Lighting 2490 includes options for easy mounting and installation. Its lightweight design coupled with intuitive controls ensures that both professional lighting technicians and newcomers can operate it with ease.

Overall, the Acclaim Lighting 2490 stands as a testament to the brand's commitment to quality and innovation in lighting technology. With its combination of efficiency, versatility, and durability, it offers a comprehensive solution for a wide array of lighting needs, making it a preferred choice among lighting designers and professionals alike.
Top Page Image Contents