Hoover F5906900 owner manual To clean nozzle, Read Before you begin cleaning instructions on

If rinsing is desired, be careful not to over-wet the carpet or upholstery.

Allow time for carpet or upholstery to dry completely between cleaning and rinsing. To rinse, follow the same proce-

dure for cleaning only using hot tap water with no detergent in the upper clean solution tank.

c. Empty tanks, rinse with clear water and let air dry. Rinse the solution tank cap and recovery tank lid and let air dry.

3-1

d. Remove debris from recovery tank fil- ter and rinse with clean water.

To clean nozzle

If lint or other debris becomes lodged in nozzle, do not attempt to remove nozzle cover.

Pour one to two cups of clear water on a non-carpeted floor. Do not pour water onto a wood floor.

Pick up water with your ‘SteamVac’ deep cleaner. Repeat as necessary until debris is flushed out of nozzle.

To clean the outside of the machine, wipe off dirt with a cloth dampened in warm water and mild detergent. Do not use solvent or petroleum based prod- ucts to clean the machine.

Carpet Cleaning

Read “Before you begin cleaning” instructions on page 9.

1.Fill clean solution tank (upper tank) with HOOVER Deep Cleansing™ Detergent according to instructions on pages 7 and 8.

3-2

2.Move speed selector to LO for gen- tle cleaning or Hl for normal cleaning.

3.Dry hands and plug cord into a prop- erly grounded outlet.

Do not clean over floor electrical out- lets.

Note: If the filter must be removed for cleaning, it is easier to replace if the fil- ter is wet.

e. If desired, vacuum thoroughly after carpet has completely dried. This will help reduce any shading left by the deep cleaner’s brushes.

4.To avoid walking on damp carpet, start at the end of the room farthest from the door or path to sink where tanks will be emptied and filled.

Step on handle release pedal and lower handle to operating position; turn deep cleaner ON.

5. Squeeze trigger to release cleaning

solution and slowly push deep cleaner

forward (equals one wet stroke).

Picking up spills Cleaning bare floors

6. Continue to squeeze trigger and slow-

ly pull deep cleaner back toward you

(second wet stroke). Release trigger and

slowly push deep cleaner forward over

area just sprayed with solution (dry

stroke). Then slowly pull deep cleaner

back toward you without squeezing trig-

ger (dry stroke).

7. Overlap strokes by 1 inch to help pre-

vent streaking.

Keep nozzle flat on floor for both forward

and reverse strokes.

8. For heavily soiled areas, repeat steps

5-7.

Note: To avoid saturating carpet, do not use more than 4 wet strokes over one area. Always end with dry strokes.

It is best to alternate wet and dry strokes as described above.

For best cleaning results and to aid in faster drying of carpet, end with more dry strokes. (Continue using dry strokes until little water is visible passing through the recovery tank lid.)

Empty recovery tank when the motor sound becomes higher pitched and there is a loss in suction (see “Automatic shut-off”, page 7).

When finished cleaning, follow “After cleaning” instructions on pages 9 and 10.

10

Your HOOVER SteamVac deep cleaner may also be used to pick up small liq- uid spills (1 gallon or less, never to exceed 1/4 inch in depth) on carpet, upholstery, or bare floors.

For best results, pick up spills immedi- ately by placing the stair/upholstery noz- zle just above the spill and suction up any residue on top of the carpet. If the spill remains, place either the stair/ upholstery nozzle or floor nozzle with brushes turned OFF in front of the spill, pull the nozzle very slowly over the spill initially with suction only. Repeat with spray and suction.

When picking up spills on bare floors, use only the floor nozzle with the bare floor attachment in place and speed selector in the OFF position (this will help prevent spreading the spill).

If a spot is left, the stair/upholstery nozzle is generally more effective for removing it. Although no cleaning solution can com- pletely remove all spots, they can be treat- ed by following the instructions provided by the manufacturer of the carpet, upholstery, or bare floor surface being cleaned.

Do not use the SteamVac deep cleaner to pick up flammable or combustible liq- uids or chemicals.

When finished, follow “After cleaning” instructions on pages 9 and 10.

How to attach bare floor attachment (available at addi- tional cost)

Disconnect deep cleaner from electri- cal outlet.

To prevent possible leaking, remove clean solution tank and recovery tank before positioning bare attachment. Refer to Fig. 2-9 to remove clean solu- tion tank. Set tank aside (do not set tank on furniture).

Refer to Fig. 2-16 to remove recovery tank.

With handle in upright position, tilt clean- er back so that handle rests on the floor.

3-3
A
B
				R
				O
			T
		A		AB
	T		FE	R
	E	OL
N	O R O

With foam strip (A) (located under the netting) in position as shown, place attachment on front of nozzle (B). Make sure arrow on end of attachment points in the direction as shown.