Brocade Communications Systems SBCEBFCSW manual General Safety, Electrical Safety

Page 6

General Safety

Follow these rules to ensure general safety:

Observe good housekeeping in the area of the machines during and after maintenance.

When lifting any heavy object:

1.Ensure you can stand safely without slipping.

2.Distribute the weight of the object equally between your feet.

3.Use a slow lifting force. Never move suddenly, or twist,when you attempt to lift.

4.Lift by standing or by pushing up with you leg muscles; this action removes the strain from the muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35lb) or any object that you think is too heavy for you.

Do not perform any action that causes hazards to the customer, or makes the equipment unsafe.

Before you start the machine, ensure that other service representatives and the customer’s personnel are not in a hazardous position.

Place removed covers and other parts in a safe place, away from all personnel, while you are servicing the machine.

Keep your tool case away from walk areas so that other people will not trip over it.

Do not wear loose clothing that can be trapped in the moving parts of a machine. Ensure that your sleeves are fastened or rolled up above your elbows. If your hair is long, fasten it.

Insert the ends of your necktie or scarf inside clothing, or fasten it with a nonconductive clip, approximately 8 centimeters (3 inches) from the end.

Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your clothing. Remember: Metal objects are good electrical conductors.

Wear safety glasses when you are: hammering, drilling soldering, cutting wire, attaching springs, using solvents, or working in any other conditions that might be hazardous to your eyes.

After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that is worn or defective.

Reinstall all covers correctly before returning the machine to the customer.

Electrical Safety

xxCAUTION:

Electrical current from power, telephone, and communication cables can be hazardous. To avoid personal injury or equipment damage, disconnect the server system power cords, telecommunication systems, networks, and modems before you open the server covers, unless instructed otherwise in the installation and configuration procedures.

Important: Disconnect all power before performing a mechanical inspection.

Observe the following rules when working on electrical equipment.

Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not protect you when working with live electrical currents.

Many customers have rubber floor mats (near their equipment) that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.

Find the emergency power-off (EPO) switch, disconnect switch, or electrical outlet in the room. If an electrical accident occurs, you can quickly turn off the switch or unplug the power cord.

Do not work alone under hazardous conditions, or near equipment that has hazardous voltages.

Disconnect all power before:

vi

Brocade SAN Switch Module: Installation Guide

Image 6
Contents Sbcebfcsw Brocade SAN Switch Module Installation Guide Contents Brocade SAN Switch Module Installation Guide Safety and regulatory information General Safety Electrical SafetyHandling electrostatic discharge-sensitive devices Viii Use safe practices when lifting Xx Caution Regulatory specifications and disclaimers Safety complianceElectromagnetic compatibility notices USA Xiii Xiv Brocade Enterprise SAN Switch Module Sbcebfcsw for Intel Features and specifications Resource CDPage Fibre Channel switch-module standards and protocols Dimensions SFP module at 2 Gbps Mode Related documentationPage Major components of the switch module Shows the major components of the switch moduleFibre Channel switch-module major components Brocade SAN Switch Module Installation Guide Installing and replacing a switch module Installation guidelines Bay Fibre Channel switch-module functionInstalling a switch module Handling static-sensitive devicesRemoving the acoustic attenuation module Squeezing the release-lever latch Installing a switch module Removing or replacing a switch module Removing a switch module Page Brocade SAN Switch Module Installation Guide Information panel LEDs and external Fibre Channel ports Information panelLEDs Fibre Channel switch-module LEDs. Notes Port speed Green Off Configuring the switch module through the Telnet interface Connecting to the switch moduleEnter Network Password window Establishing a Telnet session through the management moduleManagement-module main window Switch Management window showing switch-module 3 example Management-module password-change window Establishing a Telnet session in a command-line window Management-module command-line interface windowTelnet command-prompt window Brocade SAN Switch Module Installation Guide Connecting to the switch module Active Session from Same Client window Management-module main window Switch Management window showing switch module 3 example Establishing a Web-interface session through a Web browser Advanced Web Tools interface window management-module viewAdvanced Web Tools interface window Web-browser view Optional features Brocade SAN Switch Module Installation Guide Getting Help and Technical Assistance Before you callBrocade SAN Switch Module Installation Guide