Brocade Communications Systems SBCEBFCSW manual Viii

Page 8

•Use the black side of a grounded work mat to provide a static-free work surface. The mat is especially useful when handling ESD-sensitive devices.

•Select a grounding system, such as those in the following list, to provide protection that meets the specific service requirement.

—Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground.

—Use an ESD common ground or reference point when working on a double-insulated or battery- operated system. You can use coax or connector-outside shells on these systems.

—Use the round ground-prong of the AC plug on AC-operated computers.

✏NOTE

The use of a grounding system is desirable but not required to protect against ESD damage.

DANGER

Electrical current from power, telephone and communication cables is hazardous.

To avoid a shock hazard:

•Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm.

•Connect all power cords to a properly wired and grounded electrical outlet.

•Connect to properly wired outlets any equipment that will be attached to this product.

•When possible, use one hand only to connect or disconnect signal cables.

•Never turn on any equipment when there is evidence of fire, water, or structural damage.

•Disconnect the attached power cords, telecommunications systems, networks, and modems before you open the device covers, unless instructed otherwise in the installation and configuration procedures.

•Connect and disconnect cables as described in the following table when installing, moving, or opening covers on this product or attached devices.

 

To Connect

 

To Disconnect

 

 

 

 

1.

Turn everything OFF.

1.

Turn everything OFF.

2.

First, attach all cables to devices.

2.

First, remove power cords from outlet.

3.

Attach signal cables to connectors.

3.

Remove signal cables from connectors.

4.

Attach power cords to outlet.

4.

Remove all cables from devices.

5.

Turn device ON.

 

 

 

 

 

 

viii

Brocade SAN Switch Module: Installation Guide

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Sbcebfcsw Brocade SAN Switch Module Installation Guide Contents Brocade SAN Switch Module Installation Guide Safety and regulatory information General Safety Electrical SafetyHandling electrostatic discharge-sensitive devices Viii Use safe practices when lifting Xx Caution Regulatory specifications and disclaimers Safety complianceElectromagnetic compatibility notices USA Xiii Xiv Brocade Enterprise SAN Switch Module Sbcebfcsw for Intel Features and specifications Resource CDPage Fibre Channel switch-module standards and protocols Dimensions SFP module at 2 Gbps Mode Related documentationPage Major components of the switch module Shows the major components of the switch moduleFibre Channel switch-module major components Brocade SAN Switch Module Installation Guide Installing and replacing a switch module Installation guidelines Bay Fibre Channel switch-module functionInstalling a switch module Handling static-sensitive devicesRemoving the acoustic attenuation module Squeezing the release-lever latch Installing a switch module Removing or replacing a switch module Removing a switch module Page Brocade SAN Switch Module Installation Guide Information panel LEDs and external Fibre Channel ports Information panelLEDs Fibre Channel switch-module LEDs. Notes Port speed Green Off Configuring the switch module through the Telnet interface Connecting to the switch moduleEnter Network Password window Establishing a Telnet session through the management moduleManagement-module main window Switch Management window showing switch-module 3 example Management-module password-change window Establishing a Telnet session in a command-line window Management-module command-line interface windowTelnet command-prompt window Brocade SAN Switch Module Installation Guide Connecting to the switch module Active Session from Same Client window Management-module main window Switch Management window showing switch module 3 example Establishing a Web-interface session through a Web browser Advanced Web Tools interface window management-module viewAdvanced Web Tools interface window Web-browser view Optional features Brocade SAN Switch Module Installation Guide Getting Help and Technical Assistance Before you callBrocade SAN Switch Module Installation Guide
Top Page Image Contents