Brocade Communications Systems SBCEBFCSW manual Installation guidelines

Page 26

The following table summarizes the application for each switch module.

Bay

Fibre Channel switch-module function

3Port 0 connection on the Intel Blade Server Fibre Channel Expansion Card in the Blade unit

4Port 1 connection on the Intel Blade Server Fibre Channel Expansion Card in the Blade unit

The second switch module port connection allows for dual paths from the blade server to external Fibre Channel devices.

Installation guidelines

Before you begin to install the switch module in the SBCE unit, read the following information:

Become familiar with the safety and handling guidelines specified under “Safety and regulatory information” on page v and “Handling static-sensitive devices” on page 13, and read the safety statements in Blade unit option documentation.

Blue on a component indicates touch points, where you can grip the component to remove it from or install it in the Blade unit, open or close a latch, and so on.

Green on a component or an green label on or near a component indicates that the component can be hot-swapped, which means that if the Blade unit and operating system support hot-swap capability, you can remove or install the component while the Blade unit is running. Green can also indicate touch points on hot-swap components. See the instructions in this chapter and the Installation and User’s Guide(s) on the Resource CD for removing or installing a specific hot-swap component and for any additional procedures that you might have to perform before you remove or install the component.

You do not have to turn off the Blade unit to install or replace any of the hot-swap modules on the rear of the Blade unit.

For a list of supported options for your SBCE unit, go to http://support.intel.com/support/motherboards/server/blade.htm.

System reliability guidelines

Attention: To help ensure proper cooling and system reliability, make sure that:

Each of the I/O bays on the rear of the SBCE unit has either a module or filler module installed.

A removed hot-swap module is replaced with an identical module or filler module within 1 minute of removal.

A removed hot-swap blade server is replaced with an identical blade server or a filler blade within 1 minute of removal.

The ventilation areas on the sides of the switch module are not blocked.

You have followed the reliability guidelines in the documentation that comes with the SBCE unit.

12

Brocade SAN Switch Module: Installation Guide

Image 26
Contents Sbcebfcsw Brocade SAN Switch Module Installation Guide Contents Brocade SAN Switch Module Installation Guide Safety and regulatory information General Safety Electrical SafetyHandling electrostatic discharge-sensitive devices Viii Use safe practices when lifting Xx Caution Regulatory specifications and disclaimers Safety complianceElectromagnetic compatibility notices USA Xiii Xiv Brocade Enterprise SAN Switch Module Sbcebfcsw for Intel Features and specifications Resource CDPage Fibre Channel switch-module standards and protocols Dimensions SFP module at 2 Gbps Mode Related documentationPage Major components of the switch module Shows the major components of the switch moduleFibre Channel switch-module major components Brocade SAN Switch Module Installation Guide Installing and replacing a switch module Installation guidelines Bay Fibre Channel switch-module functionInstalling a switch module Handling static-sensitive devicesRemoving the acoustic attenuation module Squeezing the release-lever latch Installing a switch module Removing or replacing a switch module Removing a switch module Page Brocade SAN Switch Module Installation Guide Information panel LEDs and external Fibre Channel ports Information panelLEDs Fibre Channel switch-module LEDs. Notes Port speed Green Off Configuring the switch module through the Telnet interface Connecting to the switch moduleEnter Network Password window Establishing a Telnet session through the management moduleManagement-module main window Switch Management window showing switch-module 3 example Management-module password-change window Establishing a Telnet session in a command-line window Management-module command-line interface windowTelnet command-prompt window Brocade SAN Switch Module Installation Guide Connecting to the switch module Active Session from Same Client window Management-module main window Switch Management window showing switch module 3 example Establishing a Web-interface session through a Web browser Advanced Web Tools interface window management-module viewAdvanced Web Tools interface window Web-browser view Optional features Brocade SAN Switch Module Installation Guide Getting Help and Technical Assistance Before you callBrocade SAN Switch Module Installation Guide