Harman-Kardon AVR 145 owner manual Speaker Placement, Sub

Page 18

SPEAKER PLACEMENT

Before you begin to connect cables, it is important to set up your speakers in their correct locations in the room.

Optimally, the speakers should be placed in a circle with the listening position at its center. The distance from the listening position to the video display forms the radius of the circle.

The speakers should be angled so that they directly face the listening position.

The center speaker is placed either on top of, below or mounted on the wall above or below the video display screen.

The front left and right speakers are placed along the circle, about 30 degrees from the center speaker and angled toward the listener.

It is best to place the front left/right and center speakers as close to the same height as possible, preferably at about the same height as the lis- tener’s ears. In any event the center speaker should be no more than two feet above or below the left/right speakers.

The side surround speakers should be placed 110 degrees from the center speaker, that is, slightly behind and angled toward the listener. If this isn’t feasible, place the surround speakers behind the listener, with each surround speaker facing the opposite-side front speaker. The sur- round speakers may be placed a little higher than the listener’s ears.

The subwoofer’s location is less critical, since low-frequency sounds are omnidirectional. Placing the subwoofer close to a wall or in a corner will reinforce the low frequencies, and may create a “boomy” sound. You may wish to experiment over time by placing the subwoofer where the listener normally sits and then walking around the room until the low frequencies sound best. Place the subwoofer in that spot.

NOTE: Your receiver will sound its best when the same model loudspeaker is used for all positions (other than the subwoofer). If that isn’t possible, try to use speakers made by the same manufacturer.

SUB

C

FL

FR

30°

30°

110°

110°

 

150°

150°

SL

SR

Alternate Placement

Alternate Placement

for Side Surround

for Side Surround

Left Speaker

Right Speaker

Figure 14 –

Speaker Placement

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents AVR Table of Contents Safety Information When replacement parts are required, beTime Important Safety Information Audio Section IntroductionThank you for choosing Harman Kardon Surround ModesAudio/Video Inputs With S-Video Supplied AccessoriesAudio Inputs Digital Audio InputsFRONT-PANEL Controls Message Display Source Surround Tuning Preset Stations Headphone DigitalSwitch Select Video InputsREAR-PANEL Connections Monitor Inputs Inputs 1 DMP Input Reset ModeVideo Coaxial Digital RS-232 Bridge RS-232 AM AntennaRemote Control Functions Video 3 Controls televisions and other video displaysBridge/DMP Controls an iPod docked in The Bridge AM/FM Remote Control Functions Typical Home Theater System Introduction to Home TheaterSurround Modes Multichannel AudioTypes of Cables Connecting Source Devices to the AVRConnections Speaker CablesVideo Connections Audio ConnectionsDigital Audio Analog AudioFM antenna uses a 75-ohm F-connector AntennasRS-232 Serial Port Speaker Placement SUBStep Three Connect the Antennas InstallationStep One Connect the Speakers Step Four Connect the Source ComponentsVideo 1 Source Video 3 Source Installation StepsVideo 2 Source TapeStep Six Plug in AC Power Step Five Connect Video DisplayStep Seven Insert Batteries in Remote Turn on your source device Enter a code from aboveTape Cassette Step Nine Turn On the AVR Two steps are required the first time you turn on the AVRInitial Setup Using the On-Screen Menu SystemStep One Determine Speaker Size Speaker Size Menu Step Three Manual Setup MenuStep Two Measure Speaker Distances Press the Set Button to display the Speaker Size submenuSpeaker/Channel Input Indicators Speaker Crossover MenuDelay Adjust Menu Step Four EzSet Output Level CalibrationStep Five Configure Sources This is the last step in the configuration processAdvanced users may rerun EzSet for each mode individually You are now ready to begin enjoying your new receiver Operation Sleep TimerVolume Control Turning On the AVRTone Controls HeadphonesMute Function Source SelectionVideo Input Selection Using the TunerAudio Input Selection Channel Direct InputsRecording Using TheBridgeTMUse the Numeric Keys to enter the desired preset number Radio stations may be selected in one of four waysSelecting a Surround Mode Advanced FunctionsAnalog Audio Signals Digital Audio SignalsAudio Processing and Surround Sound Surround Select Menu Screen Default Modes Dolby Surround SettingsNight Mode UpsamplingVariants are available Surround Mode Description Incoming Bitstream or SignalSee below Dolby Digital 2.0 orPresentation DTS Neo6 DTS Neo6See below 96kHz processing LogicUsing the Front-Panel Controls Setting Channel Output Levels ManuallyUsing the Remote Control With the Test Tone Using the Full-OSD MenuSystem Settings Punch-Through Programming Advanced Remote Control FunctionsDim Function MacrosMemory Resetting the RemoteProcessor Reset Press the Surround Button to erase the macroTroubleshooting Guide AVR 145 Technical Specifications DTSTable A2 Speaker/Channel Setting Defaults Appendix default settings, worksheets, remote product codesTable A1 Source Input Setting Defaults Table A3 Delay Setting DefaultsVideo Bridge/DMP Tape Tuner Channel Title Table A4 Source Input SettingsTable A5 Speaker/Channel Settings Video InputTable A6 Remote Control Codes Table A7 System SettingsVideo Cable, Satellite Remote Control Function List Reference DVD CD/CD-R FAV Aiwa Logik Teknika Aiwa Realistic Adcom RCX Alphastar ABC Rembrant

AVR 145 specifications

The Harman-Kardon AVR 145 is a compact yet powerful audio/video receiver designed to deliver an exceptional home theater experience. Launched to meet the needs of both music enthusiasts and movie lovers, the AVR 145 combines advanced technology with user-friendly features, making it a popular choice for those seeking quality sound and versatility.

One of the standout features of the AVR 145 is its impressive power output. The receiver delivers up to 50 watts per channel at 8 ohms, allowing it to produce rich and immersive audio across various media formats. This output ensures that even the most bass-heavy soundtracks and delicate dialogue are rendered with clarity and precision, enhancing the overall listening experience.

Harman-Kardon is known for its commitment to quality sound, and the AVR 145 is no exception. It supports multiple audio formats, including Dolby Digital and DTS, which provide surround sound capabilities that make movies feel like a cinematic experience at home. The receiver also includes High Definition Multimedia Interface (HDMI) inputs, supporting high-resolution video signals while simplifying connectivity between devices.

In terms of connectivity, the AVR 145 is equipped with several inputs and outputs, allowing users to connect multiple audio and video sources. It features composite video, component video, and multiple optical and coaxial digital audio inputs, making it compatible with various devices such as DVD players, game consoles, and media streaming devices. This versatility ensures that users can easily integrate the AVR 145 into their existing entertainment systems.

The user interface of the AVR 145 is thoughtfully designed, making it easy for users to navigate through settings and inputs. The built-in on-screen display offers a straightforward setup experience, and the remote control is intuitive for effortless operation. Additionally, the receiver includes a stereo mode for those who prefer a two-channel audio experience, catering to both modern surround sound setups and traditional stereo configurations.

Another notable characteristic of the AVR 145 is its compact design. With a sleek and elegant appearance, it fits seamlessly into any home entertainment setup without taking up excessive space. This aesthetic appeal, combined with its robust performance, positions the AVR 145 as a brilliant choice for anyone looking to enhance their audio experience without the bulk.

In summary, the Harman-Kardon AVR 145 stands out as a remarkable A/V receiver that combines powerful performance, versatile connectivity, and user-friendly design. Whether for movies, music, or gaming, it is an excellent addition to any home theater system, providing a reliable and high-quality audio experience for years to come.
Top Page Image Contents