Harman-Kardon AVR 145 owner manual Operation, Turning On the AVR, Sleep Timer, Volume Control

Page 31

Now that you have installed your system components and completed at least a basic configuration of your receiver, you are ready to begin enjoying your home theater system.

Turning On the AVR 145

Gently press the Master Power Switch until the word OFF is no longer visi- ble. The Power Indicator above the two power switches should light up in amber. This indicates that the AVR is in Standby mode and is ready to be turned on. Normally, you may leave the Master Power Switch in the ON position, even when the receiver is not being used.

OPERATION

To turn the receiver off, press either the Standby/On Switch on the front panel, or press the AVR Button and the OFF Button on the remote. Unless the receiver will not be used for an extended period of time (for example, if you will be on vacation), it is not necessary to turn off the Master Power Switch. When the Master Power Switch is turned off, any settings you have programmed, including system configuration and pre- set radio stations, will be preserved for up to four weeks.

Sleep Timer

You may program the AVR to play for up to 90 minutes and then turn off automatically using the sleep timer.

Press the Sleep Button on the remote, and the time until turn-off will be displayed. Each additional press of the Sleep Button will reduce the time until turn-off by 10 minutes, until the OFF setting is reached, which dis- ables the sleep timer.

Figure 44 – Power Switches

There are several ways in which the AVR 145 may be turned on:

a)Press the Standby/On Switch on the front panel.

b)Press the Source Select Button on the front panel.

Figure 45 – Source Select Button

c)Using the remote, press any one of these buttons: AVR, DVD, CD, TAPE, VID1, VID2, VID3, AM/FM, 6/8CH or The Bridge/DMP.

Figure 46 – AVR and Input Selectors

NOTE: Any time you press one of the remote’s Input Selectors (i.e., DVD, CD, TAPE, VID1, VID2, VID3 or The Bridge/DMP), the remote will switch modes so that it will only transmit the codes programmed to operate that device. In order to control the receiver, you will need to press the AVR Button to return the remote to AVR mode.

Figure 47 – Sleep Button

When the sleep timer has been set, the front-panel display will automati- cally dim to half-brightness. If you press any button on the remote or front panel, the display will return to full-brightness. The display will dim again several seconds after your last command.

If you press the Sleep Button after the timer has been set, the remaining time until turn-off will be displayed. You may press the Sleep Button to change the time until turn-off. Pressing and holding the Sleep Button will disable the sleep timer, and the SLEEP OFF message will appear.

Volume Control

The volume may be adjusted either by turning the knob on the front panel (clockwise to increase volume or counterclockwise to decrease volume), or by pressing the Volume Control Buttons on the remote. The volume is displayed as a negative number of decibels (dB) below the 0dB reference point, and may be changed in 0.5dB increments. Unlike some volume controls on other products, 0dB is the maximum volume for the AVR 145. Although it’s physically possible to turn the volume to a higher level, doing so may damage your hearing and your speakers. For certain more-dynamic audio materials, even 0dB may be too high, allowing for damage to equipment.

Figure 48 – Volume Controls

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents AVR Table of Contents When replacement parts are required, be Safety InformationTime Important Safety Information Surround Modes IntroductionThank you for choosing Harman Kardon Audio SectionDigital Audio Inputs Supplied AccessoriesAudio Inputs Audio/Video Inputs With S-VideoFRONT-PANEL Controls Video Inputs Surround Tuning Preset Stations Headphone DigitalSwitch Select Message Display SourceREAR-PANEL Connections Bridge RS-232 AM Antenna Inputs Inputs 1 DMP Input Reset ModeVideo Coaxial Digital RS-232 MonitorVideo 3 Controls televisions and other video displays Remote Control FunctionsBridge/DMP Controls an iPod docked in The Bridge AM/FM Remote Control Functions Multichannel Audio Introduction to Home TheaterSurround Modes Typical Home Theater SystemSpeaker Cables Connecting Source Devices to the AVRConnections Types of CablesAnalog Audio Audio ConnectionsDigital Audio Video ConnectionsAntennas FM antenna uses a 75-ohm F-connectorRS-232 Serial Port SUB Speaker PlacementStep Four Connect the Source Components InstallationStep One Connect the Speakers Step Three Connect the AntennasVideo 1 Source Tape Installation StepsVideo 2 Source Video 3 SourceStep Five Connect Video Display Step Six Plug in AC PowerStep Seven Insert Batteries in Remote Enter a code from above Turn on your source deviceTape Cassette Two steps are required the first time you turn on the AVR Step Nine Turn On the AVRUsing the On-Screen Menu System Initial SetupStep One Determine Speaker Size Press the Set Button to display the Speaker Size submenu Step Three Manual Setup MenuStep Two Measure Speaker Distances Speaker Size MenuSpeaker Crossover Menu Speaker/Channel Input IndicatorsStep Four EzSet Output Level Calibration Delay Adjust MenuThis is the last step in the configuration process Step Five Configure SourcesAdvanced users may rerun EzSet for each mode individually You are now ready to begin enjoying your new receiver Turning On the AVR Sleep TimerVolume Control OperationSource Selection HeadphonesMute Function Tone ControlsChannel Direct Inputs Using the TunerAudio Input Selection Video Input SelectionRadio stations may be selected in one of four ways Using TheBridgeTMUse the Numeric Keys to enter the desired preset number RecordingAdvanced Functions Selecting a Surround ModeDigital Audio Signals Analog Audio SignalsAudio Processing and Surround Sound Surround Select Menu Screen Upsampling Dolby Surround SettingsNight Mode Default ModesDolby Digital 2.0 or Surround Mode Description Incoming Bitstream or SignalSee below Variants are available96kHz processing Logic DTS Neo6See below Presentation DTS Neo6Using the Full-OSD Menu Setting Channel Output Levels ManuallyUsing the Remote Control With the Test Tone Using the Front-Panel ControlsSystem Settings Macros Advanced Remote Control FunctionsDim Function Punch-Through ProgrammingPress the Surround Button to erase the macro Resetting the RemoteProcessor Reset MemoryTroubleshooting Guide DTS AVR 145 Technical SpecificationsTable A3 Delay Setting Defaults Appendix default settings, worksheets, remote product codesTable A1 Source Input Setting Defaults Table A2 Speaker/Channel Setting DefaultsVideo Input Table A4 Source Input SettingsTable A5 Speaker/Channel Settings Video Bridge/DMP Tape Tuner Channel TitleTable A7 System Settings Table A6 Remote Control CodesVideo Cable, Satellite Remote Control Function List Reference DVD CD/CD-R FAV Aiwa Logik Teknika Aiwa Realistic Adcom RCX Alphastar ABC Rembrant

AVR 145 specifications

The Harman-Kardon AVR 145 is a compact yet powerful audio/video receiver designed to deliver an exceptional home theater experience. Launched to meet the needs of both music enthusiasts and movie lovers, the AVR 145 combines advanced technology with user-friendly features, making it a popular choice for those seeking quality sound and versatility.

One of the standout features of the AVR 145 is its impressive power output. The receiver delivers up to 50 watts per channel at 8 ohms, allowing it to produce rich and immersive audio across various media formats. This output ensures that even the most bass-heavy soundtracks and delicate dialogue are rendered with clarity and precision, enhancing the overall listening experience.

Harman-Kardon is known for its commitment to quality sound, and the AVR 145 is no exception. It supports multiple audio formats, including Dolby Digital and DTS, which provide surround sound capabilities that make movies feel like a cinematic experience at home. The receiver also includes High Definition Multimedia Interface (HDMI) inputs, supporting high-resolution video signals while simplifying connectivity between devices.

In terms of connectivity, the AVR 145 is equipped with several inputs and outputs, allowing users to connect multiple audio and video sources. It features composite video, component video, and multiple optical and coaxial digital audio inputs, making it compatible with various devices such as DVD players, game consoles, and media streaming devices. This versatility ensures that users can easily integrate the AVR 145 into their existing entertainment systems.

The user interface of the AVR 145 is thoughtfully designed, making it easy for users to navigate through settings and inputs. The built-in on-screen display offers a straightforward setup experience, and the remote control is intuitive for effortless operation. Additionally, the receiver includes a stereo mode for those who prefer a two-channel audio experience, catering to both modern surround sound setups and traditional stereo configurations.

Another notable characteristic of the AVR 145 is its compact design. With a sleek and elegant appearance, it fits seamlessly into any home entertainment setup without taking up excessive space. This aesthetic appeal, combined with its robust performance, positions the AVR 145 as a brilliant choice for anyone looking to enhance their audio experience without the bulk.

In summary, the Harman-Kardon AVR 145 stands out as a remarkable A/V receiver that combines powerful performance, versatile connectivity, and user-friendly design. Whether for movies, music, or gaming, it is an excellent addition to any home theater system, providing a reliable and high-quality audio experience for years to come.
Top Page Image Contents