Harman-Kardon AVR 145 owner manual System Settings

Page 42

ADVANCED FUNCTIONS

If you are using an external source to set your output levels, simply navi- gate to each channel and use the ⁄/¤ Buttons to adjust the level as desired.

If you would like to set your levels using the AVR 145’s internal test tone, you will need to adjust the TEST TONE SEQ and TEST TONE lines as follows.

TEST TONE SEQ: When this setting reads AUTO, the test tone will auto- matically circulate to all channels, pausing for a few moments at each channel and then moving to the next channel several seconds later, as indicated by the blinking cursor. You may adjust the level for any channel when the test tone is paused there by using the ‹/› Buttons. You may also use the ⁄/¤ Buttons at any time to move the cursor to another line, and the test tone will follow the cursor.

When this setting reads MANUAL, the test tone will not move to the next channel until you use the ⁄/¤ Buttons to move it.

TEST TONE: This line determines whether the test tone is active or not. To begin the process of setting the levels, use the ‹/› Buttons to change the setting to ON. Any time you manually move the cursor out of the channel listings area of the screen, this setting will automatically change to OFF, ending the test tone.

NOTE: Setting the channel levels while one surround mode is active does not necessarily carry over to all other modes. We recommend that after you have set the levels satisfactorily in one mode, you note the results and change to other surround modes. For those modes that don’t reflect your level settings, you may either copy the settings you obtained as a short cut, or re-do the procedure to determine the correct settings for those surround modes.

System Settings

The AVR 145 offers several system settings that allow you to make the receiver easier to use rather than directly affecting performance. Most of these settings may be accessed from the SYSTEM SETUP menu, which is selected by pressing the OSD Button and navigating to the SYSTEM SETUP line of the MASTER MENU. Press the Set Button to display the submenu.

Figure 68 – System Setup Menu Screen

VFD FADE TIME OUT: Some people find the brightness of the AVR’s front-panel display distracting during movies or listening sessions. It’s possible to dim the front-panel display completely using the Dim func- tion (see below). Alternatively, you may set the display to remain dark most of the time, lighting up only when a button is pressed or a remote command is received. This setting allows you to turn on this feature and program the amount of time the display remains lit before fading to dark.

Select a time-out period of between 3 and 10 seconds, or select OFF if you prefer to leave the displays either on or dimmed at all times.

VOLUME DEFAULT and DEFAULT VOL SET: These two settings are used together to program a volume level the AVR will always switch to when turned on. This feature avoids overtaxing the system in case the last user turned the volume very high.

Press the OSD Button to remove the display from the screen so that you may adjust the volume to a desired level while a source is playing. Make a note of the number that appears in the display, and return to the SYSTEM SETUP menu. At the DEFAULT VOL SET line, select the desired volume setting, and activate the feature by setting VOLUME DEFAULT to ON.

NOTE: Although volume is normally displayed 0.5dB incre- ments, the default volume setting only allows whole numbers.

SEMI OSD TIME OUT: At this line you may program the amount of time (2 to 5 seconds) the two-line semi-OSD on-screen messages remain, or you may deactivate the semi-OSD display altogether if you find it distracting. The same messages will continue to appear on the front panel of the receiver.

FULL OSD TIME OUT: At this line you may program the amount of time (20, 30, 40 or 50 seconds) the full-OSD menus remain visible on screen. The full-OSD system may not be deactivated.

DEFAULT SURR MODE: This setting determines how the AVR 145 will handle Dolby Digital and DTS sources. For the purposes of this setting, the “default surround mode” means the mode encoded in the program, such as Dolby Digital 5.1. With this setting ON, the receiver will always use the default surround mode in the program. When this setting is changed to OFF, the receiver will use the surround mode you selected the last time this type of audio stream was detected.

As an example, the Default Surround Mode setting can be beneficial when used with Dolby Digital 2.0 programs, such as the ones broadcast on many channels of some cable and satellite television systems. If you would prefer to play these programs in the Dolby Pro Logic II Movie surround mode, then set DEFAULT SURR MODE to OFF, and select your desired surround mode the first time a Dolby Digital 2.0 program is played. Dolby Digital 5.1 programs will still be played in 5.1-channel mode.

NOTE: For PCM and analog sources, the factory default sur- round mode is Logic 7 Music. In general, the receiver will use the surround mode selected the last time that type of signal was received.

42

Page 41 Page 43
Image 42
Page 41 Page 43
Contents AVR Table of Contents Safety Information When replacement parts are required, beTime Important Safety Information Audio Section IntroductionThank you for choosing Harman Kardon Surround ModesAudio/Video Inputs With S-Video Supplied AccessoriesAudio Inputs Digital Audio InputsFRONT-PANEL Controls Message Display Source Surround Tuning Preset Stations Headphone DigitalSwitch Select Video InputsREAR-PANEL Connections Monitor Inputs Inputs 1 DMP Input Reset ModeVideo Coaxial Digital RS-232 Bridge RS-232 AM AntennaRemote Control Functions Video 3 Controls televisions and other video displaysBridge/DMP Controls an iPod docked in The Bridge AM/FM Remote Control Functions Typical Home Theater System Introduction to Home TheaterSurround Modes Multichannel AudioTypes of Cables Connecting Source Devices to the AVRConnections Speaker CablesVideo Connections Audio ConnectionsDigital Audio Analog AudioFM antenna uses a 75-ohm F-connector AntennasRS-232 Serial Port Speaker Placement SUBStep Three Connect the Antennas InstallationStep One Connect the Speakers Step Four Connect the Source ComponentsVideo 1 Source Video 3 Source Installation StepsVideo 2 Source TapeStep Six Plug in AC Power Step Five Connect Video DisplayStep Seven Insert Batteries in Remote Turn on your source device Enter a code from aboveTape Cassette Step Nine Turn On the AVR Two steps are required the first time you turn on the AVRInitial Setup Using the On-Screen Menu SystemStep One Determine Speaker Size Speaker Size Menu Step Three Manual Setup MenuStep Two Measure Speaker Distances Press the Set Button to display the Speaker Size submenuSpeaker/Channel Input Indicators Speaker Crossover MenuDelay Adjust Menu Step Four EzSet Output Level CalibrationStep Five Configure Sources This is the last step in the configuration processAdvanced users may rerun EzSet for each mode individually You are now ready to begin enjoying your new receiver Operation Sleep TimerVolume Control Turning On the AVRTone Controls HeadphonesMute Function Source SelectionVideo Input Selection Using the TunerAudio Input Selection Channel Direct InputsRecording Using TheBridgeTMUse the Numeric Keys to enter the desired preset number Radio stations may be selected in one of four waysSelecting a Surround Mode Advanced FunctionsAnalog Audio Signals Digital Audio SignalsAudio Processing and Surround Sound Surround Select Menu Screen Default Modes Dolby Surround SettingsNight Mode UpsamplingVariants are available Surround Mode Description Incoming Bitstream or SignalSee below Dolby Digital 2.0 orPresentation DTS Neo6 DTS Neo6See below 96kHz processing LogicUsing the Front-Panel Controls Setting Channel Output Levels ManuallyUsing the Remote Control With the Test Tone Using the Full-OSD MenuSystem Settings Punch-Through Programming Advanced Remote Control FunctionsDim Function MacrosMemory Resetting the RemoteProcessor Reset Press the Surround Button to erase the macroTroubleshooting Guide AVR 145 Technical Specifications DTSTable A2 Speaker/Channel Setting Defaults Appendix default settings, worksheets, remote product codesTable A1 Source Input Setting Defaults Table A3 Delay Setting DefaultsVideo Bridge/DMP Tape Tuner Channel Title Table A4 Source Input SettingsTable A5 Speaker/Channel Settings Video InputTable A6 Remote Control Codes Table A7 System SettingsVideo Cable, Satellite Remote Control Function List Reference DVD CD/CD-R FAV Aiwa Logik Teknika Aiwa Realistic Adcom RCX Alphastar ABC Rembrant

AVR 145 specifications

The Harman-Kardon AVR 145 is a compact yet powerful audio/video receiver designed to deliver an exceptional home theater experience. Launched to meet the needs of both music enthusiasts and movie lovers, the AVR 145 combines advanced technology with user-friendly features, making it a popular choice for those seeking quality sound and versatility.

One of the standout features of the AVR 145 is its impressive power output. The receiver delivers up to 50 watts per channel at 8 ohms, allowing it to produce rich and immersive audio across various media formats. This output ensures that even the most bass-heavy soundtracks and delicate dialogue are rendered with clarity and precision, enhancing the overall listening experience.

Harman-Kardon is known for its commitment to quality sound, and the AVR 145 is no exception. It supports multiple audio formats, including Dolby Digital and DTS, which provide surround sound capabilities that make movies feel like a cinematic experience at home. The receiver also includes High Definition Multimedia Interface (HDMI) inputs, supporting high-resolution video signals while simplifying connectivity between devices.

In terms of connectivity, the AVR 145 is equipped with several inputs and outputs, allowing users to connect multiple audio and video sources. It features composite video, component video, and multiple optical and coaxial digital audio inputs, making it compatible with various devices such as DVD players, game consoles, and media streaming devices. This versatility ensures that users can easily integrate the AVR 145 into their existing entertainment systems.

The user interface of the AVR 145 is thoughtfully designed, making it easy for users to navigate through settings and inputs. The built-in on-screen display offers a straightforward setup experience, and the remote control is intuitive for effortless operation. Additionally, the receiver includes a stereo mode for those who prefer a two-channel audio experience, catering to both modern surround sound setups and traditional stereo configurations.

Another notable characteristic of the AVR 145 is its compact design. With a sleek and elegant appearance, it fits seamlessly into any home entertainment setup without taking up excessive space. This aesthetic appeal, combined with its robust performance, positions the AVR 145 as a brilliant choice for anyone looking to enhance their audio experience without the bulk.

In summary, the Harman-Kardon AVR 145 stands out as a remarkable A/V receiver that combines powerful performance, versatile connectivity, and user-friendly design. Whether for movies, music, or gaming, it is an excellent addition to any home theater system, providing a reliable and high-quality audio experience for years to come.
Top Page Image Contents