Harman-Kardon AVR 145 Advanced Remote Control Functions, Dim Function, Punch-Through Programming

Page 43

ADVANCED FUNCTIONS

OSD BACKGROUND: This setting allows you to choose between a blue or black background for the full-OSD menus.

NOTE: It isn’t possible to view video sources while the full-OSD menus are displayed.

Dim Function

Some people find the front-panel messages to be distracting and would prefer to dim them or turn them off altogether.

To dim the display:

1.Press the Dim Button on the remote. Each button press will cycle through the three settings of:

VFD FULL: Normal brightness

VFD HALF: Display is dimmed but still visible; the light inside the vol- ume knob goes dark

VFD OFF: Display goes completely dark except for Power Indicator to remind you that the receiver is turned on

2.Press the Set Button on the front panel and hold it for about five sec- onds. A message indicating the current brightness setting (see above) will appear in the display. Use the front-panel ‹/› Buttons to change the setting.

Advanced Remote Control Functions

The AVR 145 remote control not only operates the AVR 145, but it also serves as a universal remote that may be programmed to operate many of your other home theater components, as described in the Installation section. Each time you select one of your other components, the AVR remote switches to the control functions for that component. Since many buttons will have unique functions for each component, you may wish to refer to the Function List in the Appendix for assistance in oper- ating your other components. The function of each button will not nec- essarily correspond to the label printed on the button.

Punch-Through Programming

The AVR 145 remote allows you to select one component for the remote to operate, while simultaneously setting certain groups of con- trols to operate another component. For example, while using the AVR to control surround modes and other audio functions, you may wish to operate the transport controls of your DVD player. Or while using the remote to control video functions on your TV, you may wish to use your cable box to change channels and the AVR to control the volume.

All of this is possible using punch-through programming.

NOTE: It is not necessary to program the remote to control your DVD player’s transport controls while the AVR is in use, as the remote is preprogrammed at the factory with this function.

To program punch-through control while operating any device:

1. Simultaneously press and hold the Input Selector (or AVR selector) for

the main device the remote will be operating and the Mute button until the LED flashes and the remote enters program mode.

2.Select the type of punch-through programming.

a)To program volume control punch-through, press the Volume Up Button.

b)To program channel control punch-through, press the Volume Down Button.

c)To program transport control punch-through, press the Play Button.

3.Press the Input Selector (or AVR selector) for the device whose vol- ume, channel or transport controls you would like to be active while operating the device you selected in the first step. The LED will flash green to confirm the programming.

For example, if you wish to watch your TV (programmed into the Video 3 button) while changing channels using your cable box (Video 2), you would first press the Video 3 and Mute buttons until the LED flashed.

You would then press the Play Button, followed by the Video 2 button.

To undo punch-through programming, follow the same steps as above, but press the same Input (or AVR) Selector in steps 1 and 3.

Macros

Macros are used to program sequences of up to nineteen commands that are executed with a single button press. Macros are well-suited for power on and off commands, or to send out a favorite multi-digit chan- nel number with one button press, or to have the ability to send out a code sequence to control another device while the remote is operating one device but with more flexibility than the built-in punch-through con- trols.

Some commands may not be programmed into macros: Mute, Dim, Channel Up/Down, any of the surround mode commands.

NOTE: Use caution when programming complicated macros. It isn’t possible to program a pause or delay before sending com- mands after Power On, and the component may not be ready to respond to commands instantaneously after powering on.

To program, or “record” a macro, follow these steps:

1.Simultaneously press one of the four Macro Buttons or the Power On Button and the Mute Button at the same time to enter program mode.

2.Press the Input (or AVR) Selector for each device before you enter commands to be transmitted to that device. This step counts as one of the 19 commands allowed for each macro.

3.For the Power On command, do not press the Power On button. Press the Mute Button instead.

4.Press the Power Off Button to program the Power Off command.

5.Press the Sleep Button to end the programming process.

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents AVR Table of Contents When replacement parts are required, be Safety InformationTime Important Safety Information Surround Modes IntroductionThank you for choosing Harman Kardon Audio SectionDigital Audio Inputs Supplied AccessoriesAudio Inputs Audio/Video Inputs With S-VideoFRONT-PANEL Controls Video Inputs Surround Tuning Preset Stations Headphone DigitalSwitch Select Message Display SourceREAR-PANEL Connections Bridge RS-232 AM Antenna Inputs Inputs 1 DMP Input Reset ModeVideo Coaxial Digital RS-232 MonitorVideo 3 Controls televisions and other video displays Remote Control FunctionsBridge/DMP Controls an iPod docked in The Bridge AM/FM Remote Control Functions Multichannel Audio Introduction to Home TheaterSurround Modes Typical Home Theater SystemSpeaker Cables Connecting Source Devices to the AVRConnections Types of CablesAnalog Audio Audio ConnectionsDigital Audio Video ConnectionsAntennas FM antenna uses a 75-ohm F-connectorRS-232 Serial Port SUB Speaker PlacementStep Four Connect the Source Components InstallationStep One Connect the Speakers Step Three Connect the AntennasVideo 1 Source Tape Installation StepsVideo 2 Source Video 3 SourceStep Five Connect Video Display Step Six Plug in AC PowerStep Seven Insert Batteries in Remote Enter a code from above Turn on your source deviceTape Cassette Two steps are required the first time you turn on the AVR Step Nine Turn On the AVRUsing the On-Screen Menu System Initial SetupStep One Determine Speaker Size Press the Set Button to display the Speaker Size submenu Step Three Manual Setup MenuStep Two Measure Speaker Distances Speaker Size MenuSpeaker Crossover Menu Speaker/Channel Input IndicatorsStep Four EzSet Output Level Calibration Delay Adjust MenuThis is the last step in the configuration process Step Five Configure SourcesAdvanced users may rerun EzSet for each mode individually You are now ready to begin enjoying your new receiver Turning On the AVR Sleep TimerVolume Control OperationSource Selection HeadphonesMute Function Tone ControlsChannel Direct Inputs Using the TunerAudio Input Selection Video Input SelectionRadio stations may be selected in one of four ways Using TheBridgeTMUse the Numeric Keys to enter the desired preset number RecordingAdvanced Functions Selecting a Surround ModeDigital Audio Signals Analog Audio SignalsAudio Processing and Surround Sound Surround Select Menu Screen Upsampling Dolby Surround SettingsNight Mode Default ModesDolby Digital 2.0 or Surround Mode Description Incoming Bitstream or SignalSee below Variants are available96kHz processing Logic DTS Neo6See below Presentation DTS Neo6Using the Full-OSD Menu Setting Channel Output Levels ManuallyUsing the Remote Control With the Test Tone Using the Front-Panel ControlsSystem Settings Macros Advanced Remote Control FunctionsDim Function Punch-Through ProgrammingPress the Surround Button to erase the macro Resetting the RemoteProcessor Reset MemoryTroubleshooting Guide DTS AVR 145 Technical SpecificationsTable A3 Delay Setting Defaults Appendix default settings, worksheets, remote product codesTable A1 Source Input Setting Defaults Table A2 Speaker/Channel Setting DefaultsVideo Input Table A4 Source Input SettingsTable A5 Speaker/Channel Settings Video Bridge/DMP Tape Tuner Channel TitleTable A7 System Settings Table A6 Remote Control CodesVideo Cable, Satellite Remote Control Function List Reference DVD CD/CD-R FAV Aiwa Logik Teknika Aiwa Realistic Adcom RCX Alphastar ABC Rembrant

AVR 145 specifications

The Harman-Kardon AVR 145 is a compact yet powerful audio/video receiver designed to deliver an exceptional home theater experience. Launched to meet the needs of both music enthusiasts and movie lovers, the AVR 145 combines advanced technology with user-friendly features, making it a popular choice for those seeking quality sound and versatility.

One of the standout features of the AVR 145 is its impressive power output. The receiver delivers up to 50 watts per channel at 8 ohms, allowing it to produce rich and immersive audio across various media formats. This output ensures that even the most bass-heavy soundtracks and delicate dialogue are rendered with clarity and precision, enhancing the overall listening experience.

Harman-Kardon is known for its commitment to quality sound, and the AVR 145 is no exception. It supports multiple audio formats, including Dolby Digital and DTS, which provide surround sound capabilities that make movies feel like a cinematic experience at home. The receiver also includes High Definition Multimedia Interface (HDMI) inputs, supporting high-resolution video signals while simplifying connectivity between devices.

In terms of connectivity, the AVR 145 is equipped with several inputs and outputs, allowing users to connect multiple audio and video sources. It features composite video, component video, and multiple optical and coaxial digital audio inputs, making it compatible with various devices such as DVD players, game consoles, and media streaming devices. This versatility ensures that users can easily integrate the AVR 145 into their existing entertainment systems.

The user interface of the AVR 145 is thoughtfully designed, making it easy for users to navigate through settings and inputs. The built-in on-screen display offers a straightforward setup experience, and the remote control is intuitive for effortless operation. Additionally, the receiver includes a stereo mode for those who prefer a two-channel audio experience, catering to both modern surround sound setups and traditional stereo configurations.

Another notable characteristic of the AVR 145 is its compact design. With a sleek and elegant appearance, it fits seamlessly into any home entertainment setup without taking up excessive space. This aesthetic appeal, combined with its robust performance, positions the AVR 145 as a brilliant choice for anyone looking to enhance their audio experience without the bulk.

In summary, the Harman-Kardon AVR 145 stands out as a remarkable A/V receiver that combines powerful performance, versatile connectivity, and user-friendly design. Whether for movies, music, or gaming, it is an excellent addition to any home theater system, providing a reliable and high-quality audio experience for years to come.
Top Page Image Contents