Harman-Kardon AVR 145 owner manual Using the Tuner, Audio Input Selection, Video Input Selection

Page 33

INDEPENDENT, the AVR 145 will change the speaker size configuration to the one you programmed for the source. If you selected a surround mode for the source, the AVR 145 will switch to that mode.

The source name will appear in the upper line of the front-panel display. If you retitled the source, only the new title will appear. Otherwise, the audio input assigned to the source (analog or one of the digital audio inputs) will also appear. The surround mode will be displayed on the lower line. The same information will also appear on screen in the semi-OSD, unless you have set the semi-OSD to OFF in the System Setup menu.

Audio Input Selection

The AVR 145 is programmed at the factory to use the analog audio inputs for each source (except for the DVD and Video 2 sources, which default to Coax 1 and Optical 1). To assign a digital audio input to a source (if you have not done so using the Input Setup menu during Initial Setup), press the Digital Button on the remote or front panel. The current audio input selection will flash in the display, and you may press the ⁄/¤ (or ‹/› on the front panel) Buttons to scroll through the audio inputs. When the desired input appears, press the Set Button to select it.

Figure 53 – Digital Input Selection

If the Auto Poll feature has been left ON in the Input Setup menu, and if a digital audio input has been assigned to the source, the AVR 145 will first check the digital audio input for a signal. If a signal is present, the AVR 145 will select the digital audio input. If no signal is present, the AVR 145 will switch to the analog audio inputs for the source.

Video Input Selection

When a source is selected, the AVR 145 switches to a video input as follows:

The COMPONENT IN line of the Input Setup menu indicates which of the two component video inputs on the AVR 145 is assigned to each source. All of the sources listed in the left column of the Source Indicators display on the front panel are assigned to the Component Video 2 inputs by default, and the sources listed in the right column default to the Component Video 1 sources. This list appears in Figure 54.

 

DIGITAL

LOGIC 7

VID 1

DVD

 

PRO LOGIC

 

VID 2

CD

 

3 STEREO

DSP

VID 3

FMAM

 

 

 

 

 

5 7 CH. STEREO

 

TAPE

 

 

 

 

 

SURR. OFF

 

6 8 CH

 

 

 

 

 

 

 

 

Figure 54 – Front-Panel Input Indicators

You may reassign either component video input to another source, but there is no option to disable the component video inputs for any source. If a signal is present at the component video input assigned to that

OPERATION

source, it will be selected. If your device is not using component video, make sure that other devices connected to the component video inputs are turned off.

If no signal is present at the component video input, then the S-video or composite video input for the source will be selected. It is not possible to reassign the S-video or composite video inputs to other sources.

For audio-only sources, such as the tuner or CD inputs, when no component video signal is present, the last-used video source will be selected.

6-Channel Direct Inputs

If you wish to hear audio through the 6-Channel Direct Inputs together with video, then connect your multichannel player to the Component Video 1 Inputs (the default for the 6-Channel Inputs), and the correct audio and video inputs will be selected when you select 6CH as your source. If your multichannel player uses S-video or composite video connections, you will first need to select the source you connected the video output to (e.g., DVD), and then select the 6CH source.

Figure 55 – 6-Channel Input Selector

NOTE: The 6-Channel Inputs pass the incoming signals directly to the volume control, without digitizing or processing them. Therefore, you will need to configure bass management settings (i.e., speaker size, delay and output level) on your source device so that they match the settings you programmed using the Manual Setup menu. Consult the owner’s guide for your multi- channel player for more information.

Using the Tuner

The AVR 145’s built-in tuner may be selected in one of three ways:

1.Press the Source Selector Button on the front panel repeatedly until the tuner is selected. The last-used band (AM or FM) will be active.

2.Press the Tuner Band Button (marked AM/FM). Press this button again to switch bands.

3.Press the Tuner Input Selector (marked AM/FM) on the remote. Press this button again to switch bands.

Figure 56 – Tuner Input Selection

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents AVR Table of Contents Safety Information When replacement parts are required, beTime Important Safety Information Thank you for choosing Harman Kardon IntroductionAudio Section Surround ModesAudio Inputs Supplied AccessoriesAudio/Video Inputs With S-Video Digital Audio InputsFRONT-PANEL Controls Switch Select Surround Tuning Preset Stations Headphone DigitalMessage Display Source Video InputsREAR-PANEL Connections Video Coaxial Digital RS-232 Inputs Inputs 1 DMP Input Reset ModeMonitor Bridge RS-232 AM AntennaRemote Control Functions Video 3 Controls televisions and other video displaysBridge/DMP Controls an iPod docked in The Bridge AM/FM Remote Control Functions Surround Modes Introduction to Home TheaterTypical Home Theater System Multichannel AudioConnections Connecting Source Devices to the AVRTypes of Cables Speaker CablesDigital Audio Audio ConnectionsVideo Connections Analog AudioFM antenna uses a 75-ohm F-connector AntennasRS-232 Serial Port SUB Speaker PlacementStep One Connect the Speakers InstallationStep Three Connect the Antennas Step Four Connect the Source ComponentsVideo 1 Source Video 2 Source Installation StepsVideo 3 Source TapeStep Six Plug in AC Power Step Five Connect Video DisplayStep Seven Insert Batteries in Remote Turn on your source device Enter a code from aboveTape Cassette Two steps are required the first time you turn on the AVR Step Nine Turn On the AVRInitial Setup Using the On-Screen Menu SystemStep One Determine Speaker Size Step Two Measure Speaker Distances Step Three Manual Setup MenuSpeaker Size Menu Press the Set Button to display the Speaker Size submenuSpeaker Crossover Menu Speaker/Channel Input IndicatorsStep Four EzSet Output Level Calibration Delay Adjust MenuStep Five Configure Sources This is the last step in the configuration processAdvanced users may rerun EzSet for each mode individually You are now ready to begin enjoying your new receiver Volume Control Sleep TimerOperation Turning On the AVRMute Function HeadphonesTone Controls Source SelectionAudio Input Selection Using the TunerVideo Input Selection Channel Direct InputsUse the Numeric Keys to enter the desired preset number Using TheBridgeTMRecording Radio stations may be selected in one of four waysAdvanced Functions Selecting a Surround ModeAnalog Audio Signals Digital Audio SignalsAudio Processing and Surround Sound Surround Select Menu Screen Night Mode Dolby Surround SettingsDefault Modes UpsamplingSee below Surround Mode Description Incoming Bitstream or SignalVariants are available Dolby Digital 2.0 orSee below DTS Neo6Presentation DTS Neo6 96kHz processing LogicUsing the Remote Control With the Test Tone Setting Channel Output Levels ManuallyUsing the Front-Panel Controls Using the Full-OSD MenuSystem Settings Dim Function Advanced Remote Control FunctionsPunch-Through Programming MacrosProcessor Reset Resetting the RemoteMemory Press the Surround Button to erase the macroTroubleshooting Guide DTS AVR 145 Technical SpecificationsTable A1 Source Input Setting Defaults Appendix default settings, worksheets, remote product codesTable A2 Speaker/Channel Setting Defaults Table A3 Delay Setting DefaultsTable A5 Speaker/Channel Settings Table A4 Source Input SettingsVideo Bridge/DMP Tape Tuner Channel Title Video InputTable A6 Remote Control Codes Table A7 System SettingsVideo Cable, Satellite Remote Control Function List Reference DVD CD/CD-R FAV Aiwa Logik Teknika Aiwa Realistic Adcom RCX Alphastar ABC Rembrant

AVR 145 specifications

The Harman-Kardon AVR 145 is a compact yet powerful audio/video receiver designed to deliver an exceptional home theater experience. Launched to meet the needs of both music enthusiasts and movie lovers, the AVR 145 combines advanced technology with user-friendly features, making it a popular choice for those seeking quality sound and versatility.

One of the standout features of the AVR 145 is its impressive power output. The receiver delivers up to 50 watts per channel at 8 ohms, allowing it to produce rich and immersive audio across various media formats. This output ensures that even the most bass-heavy soundtracks and delicate dialogue are rendered with clarity and precision, enhancing the overall listening experience.

Harman-Kardon is known for its commitment to quality sound, and the AVR 145 is no exception. It supports multiple audio formats, including Dolby Digital and DTS, which provide surround sound capabilities that make movies feel like a cinematic experience at home. The receiver also includes High Definition Multimedia Interface (HDMI) inputs, supporting high-resolution video signals while simplifying connectivity between devices.

In terms of connectivity, the AVR 145 is equipped with several inputs and outputs, allowing users to connect multiple audio and video sources. It features composite video, component video, and multiple optical and coaxial digital audio inputs, making it compatible with various devices such as DVD players, game consoles, and media streaming devices. This versatility ensures that users can easily integrate the AVR 145 into their existing entertainment systems.

The user interface of the AVR 145 is thoughtfully designed, making it easy for users to navigate through settings and inputs. The built-in on-screen display offers a straightforward setup experience, and the remote control is intuitive for effortless operation. Additionally, the receiver includes a stereo mode for those who prefer a two-channel audio experience, catering to both modern surround sound setups and traditional stereo configurations.

Another notable characteristic of the AVR 145 is its compact design. With a sleek and elegant appearance, it fits seamlessly into any home entertainment setup without taking up excessive space. This aesthetic appeal, combined with its robust performance, positions the AVR 145 as a brilliant choice for anyone looking to enhance their audio experience without the bulk.

In summary, the Harman-Kardon AVR 145 stands out as a remarkable A/V receiver that combines powerful performance, versatile connectivity, and user-friendly design. Whether for movies, music, or gaming, it is an excellent addition to any home theater system, providing a reliable and high-quality audio experience for years to come.
Top Page Image Contents