Harman-Kardon AVR 145 owner manual Step Four EzSet Output Level Calibration, Delay Adjust Menu

Page 28

INITIAL SETUP

The LFE line sets the frequency for a low-pass filter that determines what information is sent to the subwoofer for playback. Since the sub- woofer output combines low-frequency information for all channels, in order to make sure that no information is lost due to different speakers having different capabilities, the subwoofer filter should be matched to the highest crossover frequency used for any speaker group.

Looking at each of your three speaker-group settings in this menu, determine which group is set to the highest frequency. Move the cursor to the LFE line, and use the ‹/› Buttons to select that speaker group. If all three speaker groups have the same setting, you may leave the LFE filter to its factory default of the LEFT/RIGHT speaker group.

Move the cursor to the BACK TO MANUAL SETUP line and press the Set Button to return to the Manual Setup menu.

Delay Adjust Menu

As explained above in Step Two – Measure Speaker Distances, some- times the speakers are placed at different distances from the listening position, which can muddy the sound, as sounds are heard earlier or later than desired.

Even if all of your speakers are placed the same distance from the lis- tening position, you should not skip this menu.

On the Manual Setup menu, move the cursor to the DELAY ADJUST line and press the Set Button to display the Delay Adjust menu.

Figure 40 – Delay Adjust Menu Screen

This menu requires you to enter the distance from each speaker to the listening position, which you measured in Step Two – Measure Speaker Distances.

The default unit of measurement is in feet. If you wish to change the unit to meters, move the cursor down to the UNIT line, and use the ‹/› Buttons to change the unit to METER.

Use the ⁄/¤ Buttons to move the cursor to the FL (front left) line; then use the ‹/› Buttons to change the measurement as needed. Use the ⁄/¤ Buttons to move to each speaker in turn – CEN (center), FR (front right), SR (surround right), SL (surround left) and SUB (subwoofer).

DELAY RESET: This line is used if you wish to reset all of the speaker delay settings to the factory default of 10 feet (3.0 meters) at once. Use the ‹/› Buttons to change the setting of OFF to ON. If you change any speaker’s setting, this line will automatically revert to OFF.

A/V SYNC DELAY: This line allows you to compensate for a situation in which one of your source devices, or your video display, introduces a significant amount of video processing that causes the audio and video parts of the signal to get out of sync. This is known as a “lip sync” prob- lem. You may delay the audio for all channels by up to 80 milliseconds to compensate.

NOTE: We recommend that you adjust the A/V Sync Delay using the Delay Button on the remote, rather than in this menu, so that you can view the picture while adjusting the audio delay. With the program playing, press the Delay Button, and the A/V SYNC DELAY message will appear on the front panel and in the semi-OSD display. Press the Set Button to display the current delay setting, and use the ‹/› Buttons to adjust the setting until the synchronization issue is resolved.

Move the cursor to the BACK TO MANUAL SETUP line and press the Set Button to return to the Manual Setup menu, or simply press the OSD Button to exit the menu system.

Step Four – EzSet Output Level Calibration

This is an important step in the configuration process, and should not be skipped.

By now you should have connected all of your speakers and sources and your video display. You should have turned on the receiver and used the Manual Setup menus to program each of your speakers as Large or Small.

Sit in the listening position with the remote control, and make sure to eliminate external noises for the few minutes needed to run the EzSet procedure.

Use the volume control buttons on the remote to adjust the volume to –15dB.

Now point the remote at the receiver and press the SPL Button until the LED blinks, then press the “5” Key. The procedure works best if you hold the remote at about ear level, pointed toward the receiver. Try not to tilt the remote out of line with the IR receiver on the AVR’s front panel.

Figure 41 – EzSet (SPL) Button

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents AVR Table of Contents When replacement parts are required, be Safety InformationTime Important Safety Information Introduction Thank you for choosing Harman KardonAudio Section Surround ModesSupplied Accessories Audio InputsAudio/Video Inputs With S-Video Digital Audio InputsFRONT-PANEL Controls Surround Tuning Preset Stations Headphone Digital Switch SelectMessage Display Source Video InputsREAR-PANEL Connections Inputs Inputs 1 DMP Input Reset Mode Video Coaxial Digital RS-232Monitor Bridge RS-232 AM AntennaVideo 3 Controls televisions and other video displays Remote Control FunctionsBridge/DMP Controls an iPod docked in The Bridge AM/FM Remote Control Functions Introduction to Home Theater Surround ModesTypical Home Theater System Multichannel AudioConnecting Source Devices to the AVR ConnectionsTypes of Cables Speaker CablesAudio Connections Digital AudioVideo Connections Analog AudioAntennas FM antenna uses a 75-ohm F-connectorRS-232 Serial Port Speaker Placement SUBInstallation Step One Connect the SpeakersStep Three Connect the Antennas Step Four Connect the Source ComponentsVideo 1 Source Installation Steps Video 2 SourceVideo 3 Source TapeStep Five Connect Video Display Step Six Plug in AC PowerStep Seven Insert Batteries in Remote Enter a code from above Turn on your source deviceTape Cassette Step Nine Turn On the AVR Two steps are required the first time you turn on the AVRUsing the On-Screen Menu System Initial SetupStep One Determine Speaker Size Step Three Manual Setup Menu Step Two Measure Speaker DistancesSpeaker Size Menu Press the Set Button to display the Speaker Size submenuSpeaker/Channel Input Indicators Speaker Crossover MenuDelay Adjust Menu Step Four EzSet Output Level CalibrationThis is the last step in the configuration process Step Five Configure SourcesAdvanced users may rerun EzSet for each mode individually You are now ready to begin enjoying your new receiver Sleep Timer Volume ControlOperation Turning On the AVRHeadphones Mute FunctionTone Controls Source SelectionUsing the Tuner Audio Input SelectionVideo Input Selection Channel Direct InputsUsing TheBridgeTM Use the Numeric Keys to enter the desired preset numberRecording Radio stations may be selected in one of four waysSelecting a Surround Mode Advanced FunctionsDigital Audio Signals Analog Audio SignalsAudio Processing and Surround Sound Surround Select Menu Screen Dolby Surround Settings Night ModeDefault Modes UpsamplingSurround Mode Description Incoming Bitstream or Signal See belowVariants are available Dolby Digital 2.0 orDTS Neo6 See belowPresentation DTS Neo6 96kHz processing LogicSetting Channel Output Levels Manually Using the Remote Control With the Test ToneUsing the Front-Panel Controls Using the Full-OSD MenuSystem Settings Advanced Remote Control Functions Dim FunctionPunch-Through Programming MacrosResetting the Remote Processor ResetMemory Press the Surround Button to erase the macroTroubleshooting Guide AVR 145 Technical Specifications DTSAppendix default settings, worksheets, remote product codes Table A1 Source Input Setting DefaultsTable A2 Speaker/Channel Setting Defaults Table A3 Delay Setting DefaultsTable A4 Source Input Settings Table A5 Speaker/Channel SettingsVideo Bridge/DMP Tape Tuner Channel Title Video InputTable A7 System Settings Table A6 Remote Control CodesVideo Cable, Satellite Remote Control Function List Reference DVD CD/CD-R FAV Aiwa Logik Teknika Aiwa Realistic Adcom RCX Alphastar ABC Rembrant

AVR 145 specifications

The Harman-Kardon AVR 145 is a compact yet powerful audio/video receiver designed to deliver an exceptional home theater experience. Launched to meet the needs of both music enthusiasts and movie lovers, the AVR 145 combines advanced technology with user-friendly features, making it a popular choice for those seeking quality sound and versatility.

One of the standout features of the AVR 145 is its impressive power output. The receiver delivers up to 50 watts per channel at 8 ohms, allowing it to produce rich and immersive audio across various media formats. This output ensures that even the most bass-heavy soundtracks and delicate dialogue are rendered with clarity and precision, enhancing the overall listening experience.

Harman-Kardon is known for its commitment to quality sound, and the AVR 145 is no exception. It supports multiple audio formats, including Dolby Digital and DTS, which provide surround sound capabilities that make movies feel like a cinematic experience at home. The receiver also includes High Definition Multimedia Interface (HDMI) inputs, supporting high-resolution video signals while simplifying connectivity between devices.

In terms of connectivity, the AVR 145 is equipped with several inputs and outputs, allowing users to connect multiple audio and video sources. It features composite video, component video, and multiple optical and coaxial digital audio inputs, making it compatible with various devices such as DVD players, game consoles, and media streaming devices. This versatility ensures that users can easily integrate the AVR 145 into their existing entertainment systems.

The user interface of the AVR 145 is thoughtfully designed, making it easy for users to navigate through settings and inputs. The built-in on-screen display offers a straightforward setup experience, and the remote control is intuitive for effortless operation. Additionally, the receiver includes a stereo mode for those who prefer a two-channel audio experience, catering to both modern surround sound setups and traditional stereo configurations.

Another notable characteristic of the AVR 145 is its compact design. With a sleek and elegant appearance, it fits seamlessly into any home entertainment setup without taking up excessive space. This aesthetic appeal, combined with its robust performance, positions the AVR 145 as a brilliant choice for anyone looking to enhance their audio experience without the bulk.

In summary, the Harman-Kardon AVR 145 stands out as a remarkable A/V receiver that combines powerful performance, versatile connectivity, and user-friendly design. Whether for movies, music, or gaming, it is an excellent addition to any home theater system, providing a reliable and high-quality audio experience for years to come.
Top Page Image Contents