Harman-Kardon AVR 145 owner manual Important Safety Information

Page 4

SAFETY INFORMATION

Important Safety Information

Verify Line Voltage Before Use

Your AVR 145 has been designed for use with 120-volt AC current. Connection to a line voltage other than that for which it is intended can create a safety and fire hazard and may damage the unit.

If you have any questions about the voltage requirements for your specific model, or about the line voltage in your area, contact your selling dealer before plugging the unit into a wall outlet.

unit’s feet may leave marks on certain wood or veneer materials. Use caution when placing the unit on soft woods or other materials that may be damaged by heat or heavy objects. Some surface finishes may be particularly sensitive to absorbing such marks, due to a variety of factors beyond Harman Kardon's con- trol, including the nature of the finish, cleaning materials used, and normal heat and vibration caused by the use of the product, or other factors. We recommend that caution be exercised in choosing an installation location for the component and in normal maintenance practices, as your warranty will not cover this type of damage to furniture.

Do Not Use Extension Cords

To avoid safety hazards, use only the power cord attached to your unit. We do not recommend that extension cords be used with this product. As with all electrical devices, do not run power cords under rugs or carpets or place heavy objects on them. Damaged power cords should be replaced immediately by an authorized service center with a cord meeting factory specifications.

Handle the AC Power Cord Gently

When disconnecting the power cord from an AC outlet, always pull the plug; never pull the cord. If you do not intend to use the unit for any considerable length of time, disconnect the plug from the AC outlet.

Do Not Open the Cabinet

There are no user-serviceable components inside this product. Opening the cabinet may present a shock hazard, and any modification to the product will void your guarantee. If water or any metal object such as a paper clip, wire or staple acciden- tally falls inside the unit, disconnect it from the AC power source immediately, and consult an authorized service center.

CATV or Antenna Grounding

If an outside antenna or cable system is connected to this product, be certain that it is grounded so as to provide some protection against voltage surges and static charges. Section 810 of the National Electrical Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conduc- tors, location of antenna discharge unit, connection to grounding electrodes and requirements of the grounding electrode.

NOTE TO CATV SYSTEM INSTALLER: This reminder is provided to call the CATV (cable TV) system installer’s attention to article 820-40 of the NEC, which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as possible.

Installation Location

•To ensure proper operation and to avoid the potential for safety hazards, place the unit on a firm and level surface. When placing the unit on a shelf, be certain that the shelf and any mounting hardware can support the weight of the product.

•Make certain that proper space is provided both above and below the unit for ventilation. If this product will be installed in a cabinet or other enclosed area, make certain that there is sufficient air movement within the cabinet. Under some circumstances, a fan may be required.

•Do not place the unit directly on a carpeted surface.

•Avoid installation in extremely hot or cold locations, or in an area that is exposed to direct sunlight or heating equipment.

•Avoid moist or humid locations.

•Do not obstruct the ventilation slots on the top of the unit, or place objects directly over them.

•Due to the weight of the AVR 145 and the heat generated by the amplifiers, there is the remote possibility that the rubber padding on the bottom of the

4

Cleaning

When the unit gets dirty, wipe it with a clean, soft, dry cloth. If necessary, and only after unplugging the AC power cord, wipe it with a soft cloth dampened with mild soapy water, then a fresh cloth with clean water. Wipe it dry immediately with a dry cloth. NEVER use benzene, aerosol cleaners, thinner, alcohol or any other volatile cleaning agent. Do not use abrasive cleaners, as they may damage the finish of metal parts. Avoid spraying insecticide near the unit.

Moving the Unit

Before moving the unit, be certain to disconnect any interconnection cords with other components, and make certain that you disconnect the unit from the AC out- let.

Important Information for the User

This equipment has been tested and found to comply with the limits for a Class-B digital device, pursuant to Part 15 of the FCC Rules. The limits are designed to pro- vide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio-frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interfer- ence to radio communication. However, there is no guarantee that harmful interfer- ence will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept interference received, including interference that may cause undesired operation.

NOTE: Changes or modifications may cause this unit to fail to comply with Part 15 of the FCC Rules and may void the user’s authority to operate the equipment.

Unpacking

The carton and shipping materials used to protect your new receiver during ship- ment were specially designed to cushion it from shock and vibration. We suggest that you save the carton and packing materials for use in shipping if you move, or should the unit ever need repair.

To minimize the size of the carton in storage, you may wish to flatten it. This is done by carefully slitting the tape seams on the bottom and collapsing the carton. Other card- board inserts may be stored in the same manner. Packing materials that cannot be col- lapsed should be saved along with the carton in a plastic bag.

If you do not wish to save the packaging materials, please note that the carton and other sections of the shipping protection are recyclable. Please respect the environ- ment and discard those materials at a local recycling center.

It is important that you remove the protective plastic film from the front-panel lens. Leaving the film in place will affect the performance of your remote control.

Page 3 Page 5
Image 4
Page 3 Page 5
Contents AVR Table of Contents When replacement parts are required, be Safety InformationTime Important Safety Information Introduction Thank you for choosing Harman KardonAudio Section Surround ModesSupplied Accessories Audio InputsAudio/Video Inputs With S-Video Digital Audio InputsFRONT-PANEL Controls Surround Tuning Preset Stations Headphone Digital Switch SelectMessage Display Source Video InputsREAR-PANEL Connections Inputs Inputs 1 DMP Input Reset Mode Video Coaxial Digital RS-232Monitor Bridge RS-232 AM AntennaVideo 3 Controls televisions and other video displays Remote Control FunctionsBridge/DMP Controls an iPod docked in The Bridge AM/FM Remote Control Functions Introduction to Home Theater Surround ModesTypical Home Theater System Multichannel AudioConnecting Source Devices to the AVR ConnectionsTypes of Cables Speaker CablesAudio Connections Digital AudioVideo Connections Analog AudioAntennas FM antenna uses a 75-ohm F-connectorRS-232 Serial Port Speaker Placement SUBInstallation Step One Connect the SpeakersStep Three Connect the Antennas Step Four Connect the Source ComponentsVideo 1 Source Installation Steps Video 2 SourceVideo 3 Source TapeStep Five Connect Video Display Step Six Plug in AC PowerStep Seven Insert Batteries in Remote Enter a code from above Turn on your source deviceTape Cassette Step Nine Turn On the AVR Two steps are required the first time you turn on the AVRUsing the On-Screen Menu System Initial SetupStep One Determine Speaker Size Step Three Manual Setup Menu Step Two Measure Speaker DistancesSpeaker Size Menu Press the Set Button to display the Speaker Size submenuSpeaker/Channel Input Indicators Speaker Crossover MenuDelay Adjust Menu Step Four EzSet Output Level CalibrationThis is the last step in the configuration process Step Five Configure SourcesAdvanced users may rerun EzSet for each mode individually You are now ready to begin enjoying your new receiver Sleep Timer Volume ControlOperation Turning On the AVRHeadphones Mute FunctionTone Controls Source SelectionUsing the Tuner Audio Input SelectionVideo Input Selection Channel Direct InputsUsing TheBridgeTM Use the Numeric Keys to enter the desired preset numberRecording Radio stations may be selected in one of four waysSelecting a Surround Mode Advanced FunctionsDigital Audio Signals Analog Audio SignalsAudio Processing and Surround Sound Surround Select Menu Screen Dolby Surround Settings Night ModeDefault Modes UpsamplingSurround Mode Description Incoming Bitstream or Signal See belowVariants are available Dolby Digital 2.0 orDTS Neo6 See belowPresentation DTS Neo6 96kHz processing LogicSetting Channel Output Levels Manually Using the Remote Control With the Test ToneUsing the Front-Panel Controls Using the Full-OSD MenuSystem Settings Advanced Remote Control Functions Dim FunctionPunch-Through Programming MacrosResetting the Remote Processor ResetMemory Press the Surround Button to erase the macroTroubleshooting Guide AVR 145 Technical Specifications DTSAppendix default settings, worksheets, remote product codes Table A1 Source Input Setting DefaultsTable A2 Speaker/Channel Setting Defaults Table A3 Delay Setting DefaultsTable A4 Source Input Settings Table A5 Speaker/Channel SettingsVideo Bridge/DMP Tape Tuner Channel Title Video InputTable A7 System Settings Table A6 Remote Control CodesVideo Cable, Satellite Remote Control Function List Reference DVD CD/CD-R FAV Aiwa Logik Teknika Aiwa Realistic Adcom RCX Alphastar ABC Rembrant

AVR 145 specifications

The Harman-Kardon AVR 145 is a compact yet powerful audio/video receiver designed to deliver an exceptional home theater experience. Launched to meet the needs of both music enthusiasts and movie lovers, the AVR 145 combines advanced technology with user-friendly features, making it a popular choice for those seeking quality sound and versatility.

One of the standout features of the AVR 145 is its impressive power output. The receiver delivers up to 50 watts per channel at 8 ohms, allowing it to produce rich and immersive audio across various media formats. This output ensures that even the most bass-heavy soundtracks and delicate dialogue are rendered with clarity and precision, enhancing the overall listening experience.

Harman-Kardon is known for its commitment to quality sound, and the AVR 145 is no exception. It supports multiple audio formats, including Dolby Digital and DTS, which provide surround sound capabilities that make movies feel like a cinematic experience at home. The receiver also includes High Definition Multimedia Interface (HDMI) inputs, supporting high-resolution video signals while simplifying connectivity between devices.

In terms of connectivity, the AVR 145 is equipped with several inputs and outputs, allowing users to connect multiple audio and video sources. It features composite video, component video, and multiple optical and coaxial digital audio inputs, making it compatible with various devices such as DVD players, game consoles, and media streaming devices. This versatility ensures that users can easily integrate the AVR 145 into their existing entertainment systems.

The user interface of the AVR 145 is thoughtfully designed, making it easy for users to navigate through settings and inputs. The built-in on-screen display offers a straightforward setup experience, and the remote control is intuitive for effortless operation. Additionally, the receiver includes a stereo mode for those who prefer a two-channel audio experience, catering to both modern surround sound setups and traditional stereo configurations.

Another notable characteristic of the AVR 145 is its compact design. With a sleek and elegant appearance, it fits seamlessly into any home entertainment setup without taking up excessive space. This aesthetic appeal, combined with its robust performance, positions the AVR 145 as a brilliant choice for anyone looking to enhance their audio experience without the bulk.

In summary, the Harman-Kardon AVR 145 stands out as a remarkable A/V receiver that combines powerful performance, versatile connectivity, and user-friendly design. Whether for movies, music, or gaming, it is an excellent addition to any home theater system, providing a reliable and high-quality audio experience for years to come.
Top Page Image Contents