Harman-Kardon AVR 145 owner manual You are now ready to begin enjoying your new receiver

Page 30

INITIAL SETUP

you to select the correct source device even when you have forgotten which physical connections you used.

Move the cursor down to the TITLE line and press the Set Button. A block cursor will blink.

The remaining lines in the Input Setup menu activate the tone controls, and may be skipped at this time. We recommend leaving the tone con- trols at their factory defaults for most listening, in order to enjoy the sound mix created by your favorite movie and music artists. However, if your room or speakers have unusual characteristics, or simply as a mat- ter of personal preference, see the Tone Controls section on page 32 for more information.

You are now ready to begin enjoying your new receiver!

Figure 43 – Retitling a Source Input

Now you may use the ⁄/¤ Buttons to scroll through the alphabet in upper and lower case, as well as numbers and a variety of punctuation marks. When you have selected the desired character, press the › Button to move to the next space. You may also press the › Button to leave a blank. Press the Set Button when you have finished spelling out the new display name for the source.

COMPONENT IN: If you connected the source to one of the two compo- nent video inputs, make sure the correct set of inputs is displayed at this line. If it isn’t, move the cursor to this line, and then press the › Button to change the setting.

AUDIO IN: By default, the analog audio inputs are assigned to all sources at the factory other than the DVD and Video 2 sources, which default to Coax 1 and Optical 1, respectively. If you used a digital audio connection for the source, you will need to change this setting to assign the correct digital audio input to the source, even if you also connected the analog audio outputs of the source to the receiver. Move the cursor to this line, and press the ‹/› Buttons until the correct digital input appears.

AUTO POLL: The Auto Poll feature is used when both an analog audio and digital audio connection have been made for one source device. If for some reason no digital signal is available, the AVR 145 will switch to the analog inputs for the source. This situation can occur with some cable or satellite television broadcasts, where some channels are broad- cast with digital audio and others with analog audio.

For some sources, the Auto Poll feature is unnecessary and may be undesirable. For example, if your DVD player is stopped, you may not want to use the analog audio signal or you may have decided not to connect analog audio. Move the cursor to this line, and press the ‹/› Buttons until OFF appears, disabling the Auto Poll feature. With Auto Poll turned off, the receiver will only check for a signal at the audio input assigned to the source.

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents AVR Table of Contents Safety Information When replacement parts are required, beTime Important Safety Information Audio Section IntroductionThank you for choosing Harman Kardon Surround ModesAudio/Video Inputs With S-Video Supplied AccessoriesAudio Inputs Digital Audio InputsFRONT-PANEL Controls Message Display Source Surround Tuning Preset Stations Headphone DigitalSwitch Select Video InputsREAR-PANEL Connections Monitor Inputs Inputs 1 DMP Input Reset ModeVideo Coaxial Digital RS-232 Bridge RS-232 AM AntennaRemote Control Functions Video 3 Controls televisions and other video displaysBridge/DMP Controls an iPod docked in The Bridge AM/FM Remote Control Functions Typical Home Theater System Introduction to Home TheaterSurround Modes Multichannel AudioTypes of Cables Connecting Source Devices to the AVRConnections Speaker CablesVideo Connections Audio ConnectionsDigital Audio Analog AudioFM antenna uses a 75-ohm F-connector AntennasRS-232 Serial Port Speaker Placement SUBStep Three Connect the Antennas InstallationStep One Connect the Speakers Step Four Connect the Source ComponentsVideo 1 Source Video 3 Source Installation StepsVideo 2 Source TapeStep Six Plug in AC Power Step Five Connect Video DisplayStep Seven Insert Batteries in Remote Turn on your source device Enter a code from aboveTape Cassette Step Nine Turn On the AVR Two steps are required the first time you turn on the AVRInitial Setup Using the On-Screen Menu SystemStep One Determine Speaker Size Speaker Size Menu Step Three Manual Setup MenuStep Two Measure Speaker Distances Press the Set Button to display the Speaker Size submenuSpeaker/Channel Input Indicators Speaker Crossover MenuDelay Adjust Menu Step Four EzSet Output Level CalibrationStep Five Configure Sources This is the last step in the configuration processAdvanced users may rerun EzSet for each mode individually You are now ready to begin enjoying your new receiver Operation Sleep TimerVolume Control Turning On the AVRTone Controls HeadphonesMute Function Source SelectionVideo Input Selection Using the TunerAudio Input Selection Channel Direct InputsRecording Using TheBridgeTMUse the Numeric Keys to enter the desired preset number Radio stations may be selected in one of four waysSelecting a Surround Mode Advanced FunctionsAnalog Audio Signals Digital Audio SignalsAudio Processing and Surround Sound Surround Select Menu Screen Default Modes Dolby Surround SettingsNight Mode UpsamplingVariants are available Surround Mode Description Incoming Bitstream or SignalSee below Dolby Digital 2.0 orPresentation DTS Neo6 DTS Neo6See below 96kHz processing LogicUsing the Front-Panel Controls Setting Channel Output Levels ManuallyUsing the Remote Control With the Test Tone Using the Full-OSD MenuSystem Settings Punch-Through Programming Advanced Remote Control FunctionsDim Function MacrosMemory Resetting the RemoteProcessor Reset Press the Surround Button to erase the macroTroubleshooting Guide AVR 145 Technical Specifications DTSTable A2 Speaker/Channel Setting Defaults Appendix default settings, worksheets, remote product codesTable A1 Source Input Setting Defaults Table A3 Delay Setting DefaultsVideo Bridge/DMP Tape Tuner Channel Title Table A4 Source Input SettingsTable A5 Speaker/Channel Settings Video InputTable A6 Remote Control Codes Table A7 System SettingsVideo Cable, Satellite Remote Control Function List Reference DVD CD/CD-R FAV Aiwa Logik Teknika Aiwa Realistic Adcom RCX Alphastar ABC Rembrant

AVR 145 specifications

The Harman-Kardon AVR 145 is a compact yet powerful audio/video receiver designed to deliver an exceptional home theater experience. Launched to meet the needs of both music enthusiasts and movie lovers, the AVR 145 combines advanced technology with user-friendly features, making it a popular choice for those seeking quality sound and versatility.

One of the standout features of the AVR 145 is its impressive power output. The receiver delivers up to 50 watts per channel at 8 ohms, allowing it to produce rich and immersive audio across various media formats. This output ensures that even the most bass-heavy soundtracks and delicate dialogue are rendered with clarity and precision, enhancing the overall listening experience.

Harman-Kardon is known for its commitment to quality sound, and the AVR 145 is no exception. It supports multiple audio formats, including Dolby Digital and DTS, which provide surround sound capabilities that make movies feel like a cinematic experience at home. The receiver also includes High Definition Multimedia Interface (HDMI) inputs, supporting high-resolution video signals while simplifying connectivity between devices.

In terms of connectivity, the AVR 145 is equipped with several inputs and outputs, allowing users to connect multiple audio and video sources. It features composite video, component video, and multiple optical and coaxial digital audio inputs, making it compatible with various devices such as DVD players, game consoles, and media streaming devices. This versatility ensures that users can easily integrate the AVR 145 into their existing entertainment systems.

The user interface of the AVR 145 is thoughtfully designed, making it easy for users to navigate through settings and inputs. The built-in on-screen display offers a straightforward setup experience, and the remote control is intuitive for effortless operation. Additionally, the receiver includes a stereo mode for those who prefer a two-channel audio experience, catering to both modern surround sound setups and traditional stereo configurations.

Another notable characteristic of the AVR 145 is its compact design. With a sleek and elegant appearance, it fits seamlessly into any home entertainment setup without taking up excessive space. This aesthetic appeal, combined with its robust performance, positions the AVR 145 as a brilliant choice for anyone looking to enhance their audio experience without the bulk.

In summary, the Harman-Kardon AVR 145 stands out as a remarkable A/V receiver that combines powerful performance, versatile connectivity, and user-friendly design. Whether for movies, music, or gaming, it is an excellent addition to any home theater system, providing a reliable and high-quality audio experience for years to come.
Top Page Image Contents