Hague Quality Water Intl 60 SERIES manual Iron Filter and Potassium Feeder Installation Guide

Page 25

Iron Filter and Potassium Feeder Installation Guide

Important: The 61AAN is capable of treating a combination of undesirable constituents in the water (iron, manganese, and/or hydrogen sulfide). However, the filter must be applied within the operating limits stated in the WaterMax® Filter Specifications in this manual. Failure to comply with these specifications will degrade performance and possibly cause the control valve to malfunction.

Note: The iron filter should be installed after the pressure tank or water meter and before the water heater or any water softener appliance, unless otherwise recommended. See Figure 6. A minimum 3/4" pipe is required for proper function of the filter. Examine the inlet piping to make sure the pipe is not plugged with lime or iron. If the piping is plugged, it must be cleaned or replaced.

Figure 6: Iron Filter and Potassium Feeder Placement

Installation Tip: To install the filter, follow steps 1–10 of Installation Steps and Start-Up Procedures, excluding Step 4—Connect the Brine Tank. Instead, connect the potassium permanganate feeder as outlined on the following page.

Caution: Do not adjust the float assembly. This feeder is preset for a 4-ounce feed of potassium permanganate. Use care when working with potassium permanganate. Follow instructions printed on the cover of the feeder as well as the instructions on the potassium permanganate container.

WaterMax 60 Series Owner’s Manual

11/10/2008

25

Image 25

Contents Series Number Owner Pays for Year Limited WarrantyContents For Owner’s Reference General InformationSix-Button Controller Getting Maximum Efficiency From the ApplianceController Part Function Six-Button Controller,Set Time of Day Customer SettingsSet Regeneration Time Set Number of PeopleIron Type Description Checklist Before InstallationDo Not PrecautionsPrepare the Placement Area Installation Steps and Start-Up ProceduresInstallation Steps and Start-Up Procedures, Check for Leaks Set Up the ControllerPlug in the Transformer Add Water to the Brine TankBypass Valve Complete the InstallationBlending Valve Setting and Using the ControllerRegenerate Button Meaning Possible Values Comments Service SettingsDisplay Meaning Possible Values Comments Service Settings,See 72-96 Hour Operating Modes Mode 1-Timer Mode62AKQ Mode 1 Timer Mode Setting ChartNA, See Mode 1 Setting Chart Mode 2 Demand Delayed Mode Setting ChartModes 1 Salt DepthsReplenishment Procedure 62AJQ Replenishment ProcedureTools and Materials Needed Add Replenishment Media 62AJQ Replenishment Procedure,Refill Tank With Water Replace Fill PlugRegeneration Cycle Frequency Worksheet 61AAN WaterMax Iron Filter Sizing FormulaDetermine Monthly Usage Water ExampleIron Filter and Potassium Feeder Placement Iron Filter and Potassium Feeder Installation GuideStart-Up Procedures for 4-oz Potassium Permanganate Feeder Cabinet and Cover Assemblies Assembly and PartsIncorrect Correct Brine Tank Assembly Assembly and Parts,Description Quantity Cabinet and AssembliesInjector Assembly Injector AssemblyScreen 93810 Injector93223 Injector ThroatBypass Assembly Bypass AssemblyPiston Assembly HousingSensor Wire AssemblyDrive End Cap Assembly Drive End Cap Assembly90217 Valve HousingDrive Motor 93238 Drive GearConcave side Static O-Ring Brine Valve Housing Assembly90843 0.5 gpm BrineFlow Control End CapH2086 Drain Line Drain End Cap AssemblyRetainer Safety Shutoff Assembly Safety Shutoff AssemblySafety Shutoff Valve Elbow Installation Safety Shutoff Valve Elbow InstallationFill Plug Fill Plug AssemblyProblem Possible Cause Solution TroubleshootingTroubleshooting, Efficiency Statements Reading Model NumbersNumber or Letter Letter Media TypeSeries 63MAQ1 63BEQ1,2 63MXQ1 WaterMax Water Conditioner Specifications62AMQ1 62APQ1 62AJQ3Filter Purpose WaterMax Filter SpecificationsCertificates Certificates, Certificates, Page Page Series