Brother 2340CV II. Preparation before threading, Thread tree, Thread spool, Needle position

Page 10

II. Preparation before threading

Thread tree

4

Raise the telescoping thread tree to its highest position.

1

Make sure that the thread holders are in alignment above

the spool pins as illustrated left.

 

 

1Thread holder on thread tree

 

2Spool pin

 

3Spool cushion

2

4Correct position

 

3

 

Thread spool

The procedure for placing the spool of thread on the spool pin differs according to the shape of the spool.

Type A

1

2

3

If you are sewing with loosely spun nylon thread, we recom- mend that you cover the spool with the net supplied to prevent the thread from slipping off the spool.

Adapt the net to the shape of the spool.

1Spool support

2Spool cushion

3Net

Type B

3

 

1Spool support

1

2Spool mat

3Spool cap

 

2

Needle position

(1)

(2)

(1)Turn off the main power switch for safety.

(2)Set the needle bar in its highest position by turning the handwheel toward you.

Turn the handwheel to find the easiest position for threading.

8

Image 10
Contents English Español Important Safety Instructions English Page Names of parts and their functions Accessories includedCleaning brush X75906001 Hexagonal wrench Needle set Schmetz 130/705HTurning direction of motor Powering the machineHow to attach and remove the presser foot Opening and closing the front coverStitch length Instructions for the differential feed mechanismPresser foot pressure 10mm 3/8 inchTo remove the needle How to check the needleNeedle To insert the needleThread tree Spool pins as illustrated leftII. Preparation before threading Thread spoolThreading the left needle III. ThreadingNeedle threading Threading the center needleLooper threading Threading IV. Types of stitchesTri-cover stitch Three needles four threads cover stitch Left needle dial Center needle dialTwo needles three threads cover stitch Needles and threadingMm 15/64 inch Wide Tension adjustmentsBalanced tension Needle and threading Removing the fabric from the machine SewingSewing flat fabric for example, trial sewing 2Raise the presser footDo not take the seam Beginning and end of the stitching Sewing a cover stitchSewing tubular garments for example, cuffs Will prevent the seam from tearingPlain stitching Hem stitching StitchesCircular hemming VII. Machine specifications VI. MaintenanceChange the light bulb Notas Sobre EL Motor Nombres de las partes y sus funciones Accesorios incluidosAbre y cierre de la tapa delantera Encendido de la máquinaPara cambiar la dirección del motor Cómo colocar y retirar el prensatelasLargo de puntada Presión del prensatelas Para introducir la aguja AgujaPara sacar la aguja Descripción de la agujaCarrete de hilo II. Preparación antes del enhebradoArbol del hilo Posición de la agujaEnhebrado de la aguja izquierda III. EnhebradoEnhebrado de la aguja Enhebrado de la aguja centralEnhebrado del áncora IV. Tipos de puntadas Puntada de recubierto de dos agujas con tres hilos Agujas y enhebradoDisco de la aguja Disco de la aguja central Mm AnchaTensión ajustada 1Aguja central Retirada del tejido de la máquina CosturaCostura de tejido plano por ejemplo, costura de prueba 2Suba el prensatelasNo retire la costura 4Tire del tejido lentamente en la dirección de la flecha conCostura de puntada de recubierto Costura de prendas tubulares por ejemplo, puñosPuntada básica Puntada de dobladillo Dobladillo de camisetas Puntadas Puntada simpleDobladillo circular VII. Especificaciones de la máquina VI. MantenimientoCambio de la bombilla de luz English / Español 884-500 XB1148-001 0308