Brother 2340CV operation manual Powering the machine, Turning direction of motor

Page 6

Powering the machine

1

2

NOTE: (For U.S.A. only)

This foot controller can be used for sewing machine model 2340CV.

Preparation

•Insert the three-pin plug into the socket on the bottom right side of the machine. Insert the power supply plug into a power outlet.

Main Power and Sewing Light Switch

This switch turns the power and sewing light on or off. To turn on push toward “ – ” mark. To turn off push toward “ ” mark.

1Main Power and Sewing Light Switch

Operation

When the pedal is pressed lightly, the machine runs at a low speed. As the pedal is pressed further, the machine will increase speed. When the pedal is released, the machine stops.

2Foot Controller: Model N

Turning direction of motor

•The motor and hand wheel of this machine turn in a counterclockwise direction (direction of arrow). This is

the same direction as an ordinary home sewing ma- chine.

1Hand wheel

1

Opening and closing the front cover

It is necessary to open the front cover when threading this machine.

• Open the front cover by sliding it to the right and guiding the top toward you.

NOTE:

For your safety, make sure that the front cover is closed when operating the machine.

How to attach and remove the presser foot

	41	1	2
		3
	2

A

B

C 4

CAUTION

Always be sure to turn off the power before carrying out this operation.

•Turn off the main power switch or disconnect the

electric supply plug.

(1)Raise the presser foot lever. 1

(2)Set the needle to its highest position by turning the hand wheel 2 counter clockwise.

(3)Push the button on the presser foot holder and the standard foot will be released. 3 4

(4)Raise the presser foot farther by pushing the presser foot lever upward. Then remove the presser foot and store it in a safe location.

(5)Again, raise the presser foot farther by pushing the presser foot lever upward. Then place a presser foot just under the presser foot holder A so that the groove in the bottom of the presser foot holder B is aligned and catches the bar on the top of the foot C. Then lower the presser foot lever to attach the foot.

4

Image 6

Contents English Español Important Safety Instructions English Page Names of parts and their functions Accessories includedCleaning brush X75906001 Hexagonal wrench Needle set Schmetz 130/705HTurning direction of motor Powering the machineHow to attach and remove the presser foot Opening and closing the front coverStitch length Instructions for the differential feed mechanismPresser foot pressure 10mm 3/8 inchTo remove the needle How to check the needleNeedle To insert the needleThread tree Spool pins as illustrated leftII. Preparation before threading Thread spoolThreading the left needle III. ThreadingNeedle threading Threading the center needleLooper threading Threading IV. Types of stitchesTri-cover stitch Three needles four threads cover stitch Left needle dial Center needle dialTwo needles three threads cover stitch Needles and threadingTension adjustments Mm 15/64 inch WideBalanced tension Needle and threading Removing the fabric from the machine SewingSewing flat fabric for example, trial sewing 2Raise the presser footDo not take the seam Beginning and end of the stitching Sewing a cover stitchSewing tubular garments for example, cuffs Will prevent the seam from tearingStitches Plain stitching Hem stitchingCircular hemming VI. Maintenance VII. Machine specificationsChange the light bulb Notas Sobre EL Motor Nombres de las partes y sus funciones Accesorios incluidosAbre y cierre de la tapa delantera Encendido de la máquinaPara cambiar la dirección del motor Cómo colocar y retirar el prensatelasLargo de puntada Presión del prensatelas Para introducir la aguja AgujaPara sacar la aguja Descripción de la agujaCarrete de hilo II. Preparación antes del enhebradoArbol del hilo Posición de la agujaEnhebrado de la aguja izquierda III. EnhebradoEnhebrado de la aguja Enhebrado de la aguja centralEnhebrado del áncora IV. Tipos de puntadas Puntada de recubierto de dos agujas con tres hilos Agujas y enhebradoMm Ancha Disco de la aguja Disco de la aguja centralTensión ajustada 1Aguja central Retirada del tejido de la máquina CosturaCostura de tejido plano por ejemplo, costura de prueba 2Suba el prensatelasNo retire la costura 4Tire del tejido lentamente en la dirección de la flecha conCostura de puntada de recubierto Costura de prendas tubulares por ejemplo, puñosDobladillo de camisetas Puntadas Puntada simple Puntada básica Puntada de dobladilloDobladillo circular VI. Mantenimiento VII. Especificaciones de la máquinaCambio de la bombilla de luz English / Español 884-500 XB1148-001 0308