Xantrex Technology XMP 2600 instruction

Commands and Queries Reference		Alphabetical reference
TOEN?	queries the	current state of the remote	communication time out
	feature.
	Syntax	TOEN?
	Parameters	none
	Category	System	Type: Sequential
TOGRP	defines the	group of channels to be shut-down when a remote
	communication time out occurs.
	Syntax	TOGRP <int>,<int>
	Parameters	the two integers are (respectively) the high and low
		parts of a 16 bits word where each bit represent a
		Power Module. If the bit value is “0” then that
		Power Module is not part of the group. If the bit
		value is “1” then that Power Module is part of the
		group of modules that will shut-down on remote
		communication time out.
	Category	System	Type: Sequential

Do not change the group members while a remote communication time out event is valid. Changing the group members while the event is valid will not change the state of the output of the modules being removed from or added to the group.

TOGRP?	return the current definition of the group of Power Modules that will
	shut-down when a remote communication time out occurs. The
	response is made up of two decimal numbers (each in the range 0 to
	255) being the high (sent first) and low parts of a 16 bits word. Each
	bit in the response represents the membership of a Power Module in
	the group (see TOGRP command for details on bit values).
	Syntax		TOGRP?
	Parameters		none
	Category		System	Type: Sequential
TORST	resets the remote communication time out event: clears the status bit
	and performs the operation defined with the TOEN command. The
	operation performed will be:
	0	= none.
	1	= restore output state of group (see TOGRP) members.
	2	= none.
	3	= stop the sequence program.
	4	= recall from area 8.
	5	= stop the sequence program then recall from area 8.
	Syntax		TORST
	Parameters		none
	Category		System	Type: Overlapped

XMP 2600 Programming Manual rev. 1.1

63

Image 76

Xantrex Technology XMP 2600 manual Shut-down when a remote communication time out occurs

Contents

Xantrex Multiple Output Power System XMP XMP Limited What does this warranty cover and how long does it How do you get service?Warranty Last? What does this warranty not cover? Disclaimer Product Information About Your Power Supply Information Description Power Supply Symbols Safety SummaryPower Supply Grounding Input Mains Voltage Rating Output VoltagesDo Not Open The Unit Air Inlets And Air Outlet Nonoperative Modules Regulatory Approvals and Safety Agency Compliance Safety Agency CompliancePower Supply Safety Regulatory Approvals Chapters Terminology About this manualWho should use this manual Table of contents Basic Programming Commands and Queries Reference Error Codes summary Byte 1Interfacing XMP Gpib interface Serial interface ACK Programming messages formats Listening Formats Talking Formats Response Data Separator How to communicate with the XMP Using the comm. channelsUsing the Gpib bus Using an RS232 link Recovering from communication halts Using queriesUsing commands Programming the XMP Recommendations on using the XMP Initialize the XMP Enforce power-on conditions Setup the XMP 2600 status systemQuery installed Power Modules Identify the XMP Setup system level protection shutdown features Initial setup of the Power Modules Protection setup Output settingsActivation Status reporting Using advanced features Handling SRQ and the IEEE488.2 Status StructuresOn-going usage of the XMP Use queries Event enable registers Status registersEvent registers Mask registers Main status byte Main controller eventsOutput message Queue Responding to SRQ events Summary of power modules status Power modules status structureRemote communication time out Primary engine status structure What happens when power is turned on Error CodeFaults Register Events Register Usage Guidelines Basic setup and usage Output Setup Power Module output rating Overview of output setup parameters Output settings Output controlOutput activation Globally enabling the outputs Voltage / current mode Current limiting schemesFoldback Polarity and disconnect relays Reprogramming Delay RetryShutdown on current limit Linear foldback Basic Programming Setting the window thresholds Workpoint window warningUsage guidelines Enabling the window thresholds Using the events mechanism Using the warningsVoltage mode example Checking the status Protection using the workpoint window Load protectionAdditional usages OVP Arm, trigger, sync and ramp Trigger mechanismSet output to stored values Toggle the output state on/off Sync output What is output ramping? Output ramping Output ramping setup Synchronization of operationsOutput ramping initiation Simultaneous operations Using hardware Trig and Sync to serialize operations Output on/offOther operations Sequential Operations Using software OPC mechanism to serialize operations Controller notification of Operation Complete Commands to program shutdown grouping Selective shutdownShutdown grouping single, group, global Different shutdown grouping of modules Responding to communication time out events Shutdown on non-fault eventsComm. time out Turn-on and reset behavior Time out events as reflected in the status structure System Commands Queries Ieee 488.1 BUS CommandsCategories Reset GlblGLBL? Gpib Settings Commands Queries Output Control Protection Trigger Sync Commands Queries Commands QueriesRead-Back Queries Status Reporting Commands Queries Synch Alphabetical reference Mnemonic Parameters None Category System Type Sequential PRE Stores settings of all the Power Modules same as STO command Result register Syntax Return two decimal numbers, in the range 0 to 255. Each bit Cmask Close relay and a value of 1 is returned for an open relay Remove a user message from the XMP 2600 front panel display Set-up the operating mode of the XMP 2600. Re-calculate rqs Response is a series of values one for each installed Power Return output Current measurement of the Power Module. Return the state of the XMP 2600 Local Lock Flag. a value Ocrst Decimal value in the range 0 to Syntax Presence of the Polarity Reversal Relay Option Parameters None Category Settings Type Sequential Master mainframe. For the XMP 2600 this value is String in the following format mssnnn where m=minutes Result is two decimal numbers the first being the level 0t o SN? = OFF = Goto= Stop Module. Result is a decimal number in the range 0 to Shut-down when a remote communication time out occurs. Time out feature Syntax Minus sigh Syntax VLIM? Vset Commands and Queries Reference Ieee 488.2 compatible Status Structures Events Register Faults Register Error CodeEvents Enable Register Output Register Events Filtering Positive Mask Register Events Filtering Negative Mask Register Standard Event Status Register read with *ESR? PON CME EXE DDE QYE OPC Primary Status Register read with PSR? Primary Event Status Register read with PER? Status Byte Register read with *STB? Primerr Power Modules Self Test Results Byte Main Controller Error Codes summary Power Modules Errors Reported by the Power ModuleErrors Detected by the Main Controller Main Power Modules Communications errors Gpib Communications errors RS232 Communications errorsParser and Execution errors Status reporting Xantrex Technology Inc