Xantrex Technology XMP 2600 specification

Commands and Queries Reference			Alphabetical reference
RIPL?	return the current programmed output ripple for the Power Module.
	The result is two decimal numbers: the first being the level (0t o 2)
	and the second being the frequency (1 to 7).
	Syntax:	RIPL?
	Parameters	none
	Category	Settings	Type: Sequential
ROM?	return a string identifying the XMP 2600. The result is “XMP 2600
	x.xx dd/mm/yy” where: x.xx is the firmware revision code and
	dd/mm/yy is the firmware date code.
	Syntax	ROM?
	Parameters	none
	Category	System	Type: Sequential
SEQ	start / stop sequence program execution.
	Syntax	SEQ <int>
	Parameters	a value of “0” will stop and a value of “1” will start
		the Sequence Program.
	Category	System	Type: Sequential
SEQ?	return the current state of the Sequence Program. The result is a single
	decimal number of value “0” if the program is not running. If the
	program is running then the result will have two elements: the first is
	the number (1 to 99) of the step being executed and the second is the
	amount of time left until the step’s operation will be performed
	(h:mm:ss).
	Syntax	SEQ?
	Parameters	none
	Category	System	Type: Sequential
SEQCLR	clear all Sequence Program Steps (only if program is not running).
	Syntax	SEQCLR
	Parameters	none
	Category	System	Type: Sequential

XMP 2600 Programming Manual rev. 1.1

59

Image 72

Xantrex Technology XMP 2600 manual Result is two decimal numbers the first being the level 0t o

Contents

Xantrex Multiple Output Power System XMP XMP Limited What does this warranty cover and how long does it How do you get service?Warranty Last? What does this warranty not cover? Disclaimer Product Information About Your Power Supply Information Safety Summary Description Power Supply SymbolsPower Supply Grounding Input Mains Voltage Rating Output VoltagesDo Not Open The Unit Air Inlets And Air Outlet Nonoperative Modules Regulatory Approvals and Safety Agency Compliance Safety Agency CompliancePower Supply Safety Regulatory Approvals About this manual Chapters TerminologyWho should use this manual Table of contents Basic Programming Commands and Queries Reference Error Codes summary Byte 1Interfacing XMP Gpib interface Serial interface ACK Programming messages formats Listening Formats Talking Formats Response Data Separator How to communicate with the XMP Using the comm. channelsUsing the Gpib bus Using an RS232 link Recovering from communication halts Using queriesUsing commands Programming the XMP Recommendations on using the XMP Initialize the XMP Enforce power-on conditions Setup the XMP 2600 status systemQuery installed Power Modules Identify the XMP Setup system level protection shutdown features Initial setup of the Power Modules Protection setup Output settingsActivation Status reporting Using advanced features Handling SRQ and the IEEE488.2 Status StructuresOn-going usage of the XMP Use queries Event enable registers Status registersEvent registers Mask registers Main status byte Main controller eventsOutput message Queue Responding to SRQ events Summary of power modules status Power modules status structureRemote communication time out Primary engine status structure What happens when power is turned on Error CodeFaults Register Events Register Usage Guidelines Basic setup and usage Output Setup Power Module output rating Overview of output setup parameters Output settings Output controlOutput activation Globally enabling the outputs Voltage / current mode Current limiting schemesFoldback Polarity and disconnect relays Reprogramming Delay RetryShutdown on current limit Linear foldback Basic Programming Setting the window thresholds Workpoint window warningUsage guidelines Enabling the window thresholds Using the events mechanism Using the warningsVoltage mode example Checking the status Protection using the workpoint window Load protectionAdditional usages OVP Arm, trigger, sync and ramp Trigger mechanismSet output to stored values Toggle the output state on/off Sync output What is output ramping? Output ramping Output ramping setup Synchronization of operationsOutput ramping initiation Simultaneous operations Using hardware Trig and Sync to serialize operations Output on/offOther operations Sequential Operations Using software OPC mechanism to serialize operations Controller notification of Operation Complete Commands to program shutdown grouping Selective shutdownShutdown grouping single, group, global Different shutdown grouping of modules Shutdown on non-fault events Responding to communication time out eventsComm. time out Turn-on and reset behavior Time out events as reflected in the status structure Ieee 488.1 BUS Commands System Commands QueriesCategories Reset GlblGLBL? Gpib Settings Commands Queries Output Control Protection Commands Queries Trigger Sync Commands QueriesRead-Back Queries Status Reporting Commands Queries Synch Alphabetical reference Mnemonic Parameters None Category System Type Sequential PRE Stores settings of all the Power Modules same as STO command Result register Syntax Return two decimal numbers, in the range 0 to 255. Each bit Cmask Close relay and a value of 1 is returned for an open relay Remove a user message from the XMP 2600 front panel display Set-up the operating mode of the XMP 2600. Re-calculate rqs Response is a series of values one for each installed Power Return output Current measurement of the Power Module. Return the state of the XMP 2600 Local Lock Flag. a value Ocrst Decimal value in the range 0 to Syntax Presence of the Polarity Reversal Relay Option Parameters None Category Settings Type Sequential Master mainframe. For the XMP 2600 this value is String in the following format mssnnn where m=minutes Result is two decimal numbers the first being the level 0t o SN? = Goto = OFF= Stop Module. Result is a decimal number in the range 0 to Shut-down when a remote communication time out occurs. Time out feature Syntax Minus sigh Syntax VLIM? Vset Commands and Queries Reference Ieee 488.2 compatible Status Structures Events Register Faults Register Error CodeEvents Enable Register Output Register Events Filtering Positive Mask Register Events Filtering Negative Mask Register Standard Event Status Register read with *ESR? PON CME EXE DDE QYE OPC Primary Status Register read with PSR? Primary Event Status Register read with PER? Status Byte Register read with *STB? Primerr Power Modules Self Test Results Byte Main Controller Error Codes summary Power Modules Errors Reported by the Power ModuleErrors Detected by the Main Controller Main Power Modules Communications errors RS232 Communications errors Gpib Communications errorsParser and Execution errors Status reporting Xantrex Technology Inc