Xantrex Technology XMP 2600 instruction

Commands and Queries Reference			Alphabetical reference
*SAV	stores settings of all the Power Modules (same as STO command).
	Syntax	*SAV <int>
	Parameters	a decimal number in the range 0 to 9 specifying the
		storage number the XMP 2600 will store the settings
		in.
	Category	System	Type: Sequential
*SDS	initialize the contents of a storage area (causing it to be empty).
	Syntax	*SDS <int>
	Parameters	a decimal number in the range 0 to 9 specifying the
		storage number the XMP 2600 will initialize.
	Category	System	Type: Sequential
*SRE	assign new	value to the Service Request Enable Register. Re-
	calculates <rqs>.
	Syntax	*SRE <int>
	Parameters	the value to be assigned to the Register - a decimal
		number in the range 0 to 255 representing bits in the
		Register.
	Category	Status	Type: Sequential
*SRE?	return the value of the Service Request Enable Register. The value
	returned is a decimal number in the range 0 to 255 representing the
	bits of the Register.
	Syntax	*SRE?
	Parameters	none
	Category	Status	Type: Sequential
*STB?	return the value of the Status Byte Register. The value returned is a
	decimal number in the range 0 to 255 representing the bits of the
	Register.
	Syntax	*STB?
	Parameters	none
	Category	Status	Type: Sequential
*TRG	toggles the state of the Global Output Enable Flag.
	Syntax	*TRG
	Parameters	none
	Category	Trigger and Sync	Type: Sequential

XMP 2600 Programming Manual rev. 1.1

43

Image 56

Xantrex Technology XMP 2600 manual Stores settings of all the Power Modules same as STO command

Contents

Xantrex Multiple Output Power System XMP XMP Limited What does this warranty cover and how long does it How do you get service?Warranty Last? What does this warranty not cover? Disclaimer Product Information About Your Power Supply Information Power Supply Grounding Safety SummaryDescription Power Supply Symbols Input Mains Voltage Rating Output VoltagesDo Not Open The Unit Air Inlets And Air Outlet Nonoperative Modules Regulatory Approvals and Safety Agency Compliance Safety Agency CompliancePower Supply Safety Regulatory Approvals Who should use this manual About this manualChapters Terminology Table of contents Basic Programming Commands and Queries Reference Error Codes summary Byte 1Interfacing XMP Gpib interface Serial interface ACK Programming messages formats Listening Formats Talking Formats Response Data Separator How to communicate with the XMP Using the comm. channelsUsing the Gpib bus Using an RS232 link Recovering from communication halts Using queriesUsing commands Programming the XMP Recommendations on using the XMP Initialize the XMP Enforce power-on conditions Setup the XMP 2600 status systemQuery installed Power Modules Identify the XMP Setup system level protection shutdown features Initial setup of the Power Modules Protection setup Output settingsActivation Status reporting Using advanced features Handling SRQ and the IEEE488.2 Status StructuresOn-going usage of the XMP Use queries Event enable registers Status registersEvent registers Mask registers Main status byte Main controller eventsOutput message Queue Responding to SRQ events Summary of power modules status Power modules status structureRemote communication time out Primary engine status structure What happens when power is turned on Error CodeFaults Register Events Register Usage Guidelines Basic setup and usage Output Setup Power Module output rating Overview of output setup parameters Output settings Output controlOutput activation Globally enabling the outputs Voltage / current mode Current limiting schemesFoldback Polarity and disconnect relays Reprogramming Delay RetryShutdown on current limit Linear foldback Basic Programming Setting the window thresholds Workpoint window warningUsage guidelines Enabling the window thresholds Using the events mechanism Using the warningsVoltage mode example Checking the status Protection using the workpoint window Load protectionAdditional usages OVP Arm, trigger, sync and ramp Trigger mechanismSet output to stored values Toggle the output state on/off Sync output What is output ramping? Output ramping Output ramping setup Synchronization of operationsOutput ramping initiation Simultaneous operations Using hardware Trig and Sync to serialize operations Output on/offOther operations Sequential Operations Using software OPC mechanism to serialize operations Controller notification of Operation Complete Commands to program shutdown grouping Selective shutdownShutdown grouping single, group, global Different shutdown grouping of modules Comm. time out Shutdown on non-fault eventsResponding to communication time out events Turn-on and reset behavior Time out events as reflected in the status structure Categories Ieee 488.1 BUS CommandsSystem Commands Queries Reset GlblGLBL? Gpib Settings Commands Queries Output Control Protection Read-Back Queries Commands QueriesTrigger Sync Commands Queries Status Reporting Commands Queries Synch Alphabetical reference Mnemonic Parameters None Category System Type Sequential PRE Stores settings of all the Power Modules same as STO command Result register Syntax Return two decimal numbers, in the range 0 to 255. Each bit Cmask Close relay and a value of 1 is returned for an open relay Remove a user message from the XMP 2600 front panel display Set-up the operating mode of the XMP 2600. Re-calculate rqs Response is a series of values one for each installed Power Return output Current measurement of the Power Module. Return the state of the XMP 2600 Local Lock Flag. a value Ocrst Decimal value in the range 0 to Syntax Presence of the Polarity Reversal Relay Option Parameters None Category Settings Type Sequential Master mainframe. For the XMP 2600 this value is String in the following format mssnnn where m=minutes Result is two decimal numbers the first being the level 0t o SN? = Stop = Goto= OFF Module. Result is a decimal number in the range 0 to Shut-down when a remote communication time out occurs. Time out feature Syntax Minus sigh Syntax VLIM? Vset Commands and Queries Reference Ieee 488.2 compatible Status Structures Events Register Faults Register Error CodeEvents Enable Register Output Register Events Filtering Positive Mask Register Events Filtering Negative Mask Register Standard Event Status Register read with *ESR? PON CME EXE DDE QYE OPC Primary Status Register read with PSR? Primary Event Status Register read with PER? Status Byte Register read with *STB? Primerr Power Modules Self Test Results Byte Main Controller Error Codes summary Power Modules Errors Reported by the Power ModuleErrors Detected by the Main Controller Main Power Modules Communications errors Parser and Execution errors RS232 Communications errorsGpib Communications errors Status reporting Xantrex Technology Inc