Error Codes summary, Controller | Xantrex Technology XMP 2600

Status reporting

Error Codes summary

Error Codes summary

The following is a list of error codes generated by the Power Modules and the main controller of the XMP 2600.

Power

Modules

Errors Reported by the Power Module

1 Processor Watchdog was activated.

7Severe OCP error - output did not shut down.

8Severe OVP error - output did not shut down.

9Test error - VOUT zero test failed.

10Test error - half the full scale VOUT test failed.

11Test error - OVP circuit did not trip.

12Test error - OVP circuit did not reset.

13Output did not shut down.

14Sense lines voltage drop exceeded 4V.

15Current Limit was active following a three seconds period of the output being set to zero voltage during a Retry Foldback.

16Test error - output current was not zero during the output test.

17Internal Communication Time Out.

18Internal Communications buffer overflow.

19output voltage did not drop to zero during the reprogramming period when the relays were operated.

20Internal Communication Checksum error.

21Illegal command in the Internal Communications.

22Internal Communications Command Error.

Errors Detected by the Main Controller

	78	Internal Communications Time Out.
	251	Internal Communications response by the Power Module was in error.
	Errors detected during Channels Scan at Power-On
	240	Internal Communications Time Out - Power Module not installed.
	241	Power Module has failed its self-test.
	242	Internal Communications response by the Power Module was in error.
	244	Power Module did not respond with RDY.
	247	The Power Module reported spec data did not match the internal table.
	Errors detected during Retain or Recall
	248	Internal Communications Time Out - Power Module not installed.
Main	Power Modules Communications errors
Controller	1	Error during channels scan (power-on).
	2	Power Module’s response to status query was in error.
	3	Communications Interrupt Line is asserted and no Power Module responded to
		scan.
	4	Internal communication receive buffer was full.

XMP 2600 Programming Manual rev. 1.1

77

Image 90

Xantrex Technology XMP 2600 manual Error Codes summary, Power Modules Errors Reported by the Power Module, Controller

Contents

Xantrex Multiple Output Power System XMP XMP Warranty Limited What does this warranty cover and how long does itHow do you get service? Last? What does this warranty not cover? Disclaimer Product Information About Your Power Supply Information Safety Summary Description Power Supply SymbolsPower Supply Grounding Do Not Open The Unit Air Inlets And Air Outlet Input Mains Voltage RatingOutput Voltages Nonoperative Modules Power Supply Safety Regulatory Approvals and Safety Agency ComplianceSafety Agency Compliance Regulatory Approvals About this manual Chapters TerminologyWho should use this manual Table of contents Basic Programming Commands and Queries Reference Error Codes summary Byte 1Interfacing XMP Gpib interface Serial interface ACK Programming messages formats Listening Formats Talking Formats Response Data Separator Using the Gpib bus How to communicate with the XMPUsing the comm. channels Using an RS232 link Using commands Recovering from communication haltsUsing queries Programming the XMP Recommendations on using the XMP Initialize the XMP Query installed Power Modules Enforce power-on conditionsSetup the XMP 2600 status system Identify the XMP Setup system level protection shutdown features Initial setup of the Power Modules Activation Protection setupOutput settings Status reporting On-going usage of the XMP Using advanced featuresHandling SRQ and the IEEE488.2 Status Structures Use queries Event registers Event enable registersStatus registers Mask registers Output message Queue Main status byteMain controller events Responding to SRQ events Remote communication time out Summary of power modules statusPower modules status structure Primary engine status structure Faults Register What happens when power is turned onError Code Events Register Usage Guidelines Basic setup and usage Output Setup Power Module output rating Overview of output setup parameters Output activation Output settingsOutput control Globally enabling the outputs Foldback Voltage / current modeCurrent limiting schemes Polarity and disconnect relays Shutdown on current limit Reprogramming DelayRetry Linear foldback Basic Programming Usage guidelines Setting the window thresholdsWorkpoint window warning Enabling the window thresholds Voltage mode example Using the events mechanismUsing the warnings Checking the status Additional usages Protection using the workpoint windowLoad protection OVP Set output to stored values Arm, trigger, sync and rampTrigger mechanism Toggle the output state on/off Sync output What is output ramping? Output ramping Output ramping initiation Output ramping setupSynchronization of operations Simultaneous operations Other operations Using hardware Trig and Sync to serialize operationsOutput on/off Sequential Operations Using software OPC mechanism to serialize operations Controller notification of Operation Complete Shutdown grouping single, group, global Commands to program shutdown groupingSelective shutdown Different shutdown grouping of modules Shutdown on non-fault events Responding to communication time out eventsComm. time out Turn-on and reset behavior Time out events as reflected in the status structure Ieee 488.1 BUS Commands System Commands QueriesCategories GLBL? ResetGlbl Gpib Settings Commands Queries Output Control Protection Commands Queries Trigger Sync Commands QueriesRead-Back Queries Status Reporting Commands Queries Synch Alphabetical reference Mnemonic Parameters None Category System Type Sequential PRE Stores settings of all the Power Modules same as STO command Result register Syntax Return two decimal numbers, in the range 0 to 255. Each bit Cmask Close relay and a value of 1 is returned for an open relay Remove a user message from the XMP 2600 front panel display Set-up the operating mode of the XMP 2600. Re-calculate rqs Response is a series of values one for each installed Power Return output Current measurement of the Power Module. Return the state of the XMP 2600 Local Lock Flag. a value Ocrst Decimal value in the range 0 to Syntax Presence of the Polarity Reversal Relay Option Parameters None Category Settings Type Sequential Master mainframe. For the XMP 2600 this value is String in the following format mssnnn where m=minutes Result is two decimal numbers the first being the level 0t o SN? = Goto = OFF= Stop Module. Result is a decimal number in the range 0 to Shut-down when a remote communication time out occurs. Time out feature Syntax Minus sigh Syntax VLIM? Vset Commands and Queries Reference Ieee 488.2 compatible Status Structures Events Register Events Enable Register Faults RegisterError Code Output Register Events Filtering Positive Mask Register Events Filtering Negative Mask Register Standard Event Status Register read with *ESR? PON CME EXE DDE QYE OPC Primary Status Register read with PSR? Primary Event Status Register read with PER? Status Byte Register read with *STB? Primerr Power Modules Self Test Results Byte Main Controller Errors Detected by the Main Controller Error Codes summaryPower Modules Errors Reported by the Power Module Main Power Modules Communications errors RS232 Communications errors Gpib Communications errorsParser and Execution errors Status reporting Xantrex Technology Inc