Brother 2340CV VI. Maintenance, VII. Machine specifications, Change the light bulb

Page 21

VI. Maintenance

Change the light bulb

2

1

4

3

CAUTION

Always be sure to turn off the power before carrying out the following operation. The glass plate over the light bulb will be hot immediately after using the machine, therefore it is advisable to wait until the light bulb has had a chance to cool down before changing bulbs.

Changing the light bulb.

•Remove the lamp cover as shown in the illustration.

•Loosen the lightbulb cover set screw pull up the light bulb cover and remove it.

•Take out the light bulb and replace it with a new one.

1Screw

2Lamp cover

3Screw

4Light bulb cover

5Light bulb

ENGLISH

5

4

VII. Machine specifications

Stitch

One needle two thread double chain stitch

Two needles three thread cover stitch (Wide 6 mm (15/64 inch)/Narrow 3 mm(1/8 inch))

Three needles four thread cover stitch (6 mm (15/64 inch))

Sewing speed

1,000 stitches per minute

Stitch length (pitch)

2 mm to 4 mm (5/64 to 5/32 inch)

Presser foot

Free presser type

Presser foot lift

5 mm to 6 mm (3/16 to 15/64 inch)

Needle

SCHMETZ 130/705H (90/#14)

Machine net weight

7.0 kgs.

19

Image 21

Contents English Español Important Safety Instructions English Page Cleaning brush X75906001 Hexagonal wrench Accessories includedNames of parts and their functions Needle set Schmetz 130/705HHow to attach and remove the presser foot Powering the machineTurning direction of motor Opening and closing the front coverInstructions for the differential feed mechanism Stitch length10mm 3/8 inch Presser foot pressureNeedle How to check the needleTo remove the needle To insert the needleII. Preparation before threading Spool pins as illustrated leftThread tree Thread spoolNeedle threading III. ThreadingThreading the left needle Threading the center needleLooper threading Tri-cover stitch Three needles four threads cover stitch IV. Types of stitchesThreading Left needle dial Center needle dialNeedles and threading Two needles three threads cover stitchTension adjustments Mm 15/64 inch WideBalanced tension Needle and threading Sewing flat fabric for example, trial sewing SewingRemoving the fabric from the machine 2Raise the presser footDo not take the seam Sewing tubular garments for example, cuffs Sewing a cover stitchBeginning and end of the stitching Will prevent the seam from tearingStitches Plain stitching Hem stitchingCircular hemming VI. Maintenance VII. Machine specificationsChange the light bulb Notas Sobre EL Motor Accesorios incluidos Nombres de las partes y sus funcionesPara cambiar la dirección del motor Encendido de la máquinaAbre y cierre de la tapa delantera Cómo colocar y retirar el prensatelasLargo de puntada Presión del prensatelas Para sacar la aguja AgujaPara introducir la aguja Descripción de la agujaArbol del hilo II. Preparación antes del enhebradoCarrete de hilo Posición de la agujaEnhebrado de la aguja III. EnhebradoEnhebrado de la aguja izquierda Enhebrado de la aguja centralEnhebrado del áncora IV. Tipos de puntadas Agujas y enhebrado Puntada de recubierto de dos agujas con tres hilosMm Ancha Disco de la aguja Disco de la aguja centralTensión ajustada 1Aguja central Costura de tejido plano por ejemplo, costura de prueba CosturaRetirada del tejido de la máquina 2Suba el prensatelas4Tire del tejido lentamente en la dirección de la flecha con No retire la costuraCostura de prendas tubulares por ejemplo, puños Costura de puntada de recubiertoDobladillo de camisetas Puntadas Puntada simple Puntada básica Puntada de dobladilloDobladillo circular VI. Mantenimiento VII. Especificaciones de la máquinaCambio de la bombilla de luz English / Español 884-500 XB1148-001 0308