Brother 2340CV operation manual III. Threading, Needle threading, Threading the left needle

Page 11

III. Threading

Needle threading

CAUTION

333

333

Always be sure to turn off the power before carrying out the following operation.

(1) Follow the procedure described below to thread the needle.

F	6
F	5	G
	4	G
444

•Pass each thread from 333 to 444 as shown in this illustration.

•Pass the thread through the proper thread guide.

•Slide and hold the thread tension release button to the right, then pass the thread through the tension disc which is in the channel next to the tension adjustment dial. Release the but- ton.

FTension disk

GThread tension release button

1 1 1

2 2 2

3 3 3

A	D
A
	B C	6664 4 4
	777	5	5 5
	777

888

E

999

Threading the left needle

•Run the thread in the sequence illustrated, following the yellow color and the numbers next to each thread- ing point. (1-9)

Threading the center needle

•Run the thread in the sequence illustrated, following the pink color and the numbers next to each threading point. (1-9)

Threading the right needle

•Run the thread in the sequence illustrated, following the green color and the numbers next to each thread- ing point. (1-9)

CAUTION

When needle threading, always thread in this order: Left needle, center needle and then right needle.

ATo left needle

BTo center needle

CTo right needle DBranching plate

EPull about 6 cm (about 2-1/2 inches) of thread through the eye of the needle.

999 Front to back

ENGLISH

9

Image 11

Contents English Español Important Safety Instructions English Page Needle set Schmetz 130/705H Accessories includedCleaning brush X75906001 Hexagonal wrench Names of parts and their functionsOpening and closing the front cover Powering the machineHow to attach and remove the presser foot Turning direction of motorInstructions for the differential feed mechanism Stitch length10mm 3/8 inch Presser foot pressureTo insert the needle How to check the needleNeedle To remove the needleThread spool Spool pins as illustrated leftII. Preparation before threading Thread treeThreading the center needle III. ThreadingNeedle threading Threading the left needleLooper threading Left needle dial Center needle dial IV. Types of stitchesTri-cover stitch Three needles four threads cover stitch ThreadingNeedles and threading Two needles three threads cover stitchBalanced tension Tension adjustmentsMm 15/64 inch Wide Needle and threading 2Raise the presser foot SewingSewing flat fabric for example, trial sewing Removing the fabric from the machineDo not take the seam Will prevent the seam from tearing Sewing a cover stitchSewing tubular garments for example, cuffs Beginning and end of the stitchingCircular hemming StitchesPlain stitching Hem stitching Change the light bulb VI. MaintenanceVII. Machine specifications Notas Sobre EL Motor Accesorios incluidos Nombres de las partes y sus funcionesCómo colocar y retirar el prensatelas Encendido de la máquinaPara cambiar la dirección del motor Abre y cierre de la tapa delanteraLargo de puntada Presión del prensatelas Descripción de la aguja AgujaPara sacar la aguja Para introducir la agujaPosición de la aguja II. Preparación antes del enhebradoArbol del hilo Carrete de hiloEnhebrado de la aguja central III. EnhebradoEnhebrado de la aguja Enhebrado de la aguja izquierdaEnhebrado del áncora IV. Tipos de puntadas Agujas y enhebrado Puntada de recubierto de dos agujas con tres hilosTensión ajustada Mm AnchaDisco de la aguja Disco de la aguja central 1Aguja central 2Suba el prensatelas CosturaCostura de tejido plano por ejemplo, costura de prueba Retirada del tejido de la máquina4Tire del tejido lentamente en la dirección de la flecha con No retire la costuraCostura de prendas tubulares por ejemplo, puños Costura de puntada de recubiertoDobladillo circular Dobladillo de camisetas Puntadas Puntada simplePuntada básica Puntada de dobladillo Cambio de la bombilla de luz VI. MantenimientoVII. Especificaciones de la máquina English / Español 884-500 XB1148-001 0308