Briggs & Stratton Water Transfer Pump manual Contact with muffler area can result in serious burns

Page 6

WARNING

Starter cord kickback (rapid retraction) can result in bodily injury. Kickback will pull hand and arm toward engine faster than you can let go.

Broken bones, fractures, bruises, or sprains could result.

Keep hands and body clear from discharge of pump.

•When starting engine, pull cord slowly until resistance is felt and then pull rapidly to avoid kickback.

•Secure discharge hose to avoid whipping.

WARNING

Contact with muffler area can result in serious burns.

Exhaust heat/gases can ignite combustibles, structures or damage fuel tank causing a fire.

•DO NOT touch hot parts and AVOID hot exhaust gases.

•Allow equipment to cool before touching.

•Keep at least 5 feet (1.5 m) of clearance on all sides of water transfer pump including overhead.

•Code of Federal Regulation (CFR) Title 36 Parks, Forests, and Public Property require equipment powered by an internal combustion engine to have a spark arrester, maintained in effective working order, complying to USDA Forest service standard 5100-1C or later revision. In the State of California a spark arrester is required under section 4442 of the California Public resources code. Other states may have similar laws.

WARNING

Starter and other rotating parts can entangle hands, hair, clothing, or accessories.

•NEVER place hands or body parts inside of running pump or hoses.

•NEVER operate water transfer pump without protective housing or covers.

•DO NOT wear loose clothing, jewelry or anything that may be caught in the starter or other rotating parts.

•Tie up long hair and remove jewelry.

CAUTION

Excessively high operating speeds increase risk of injury and damage to water pump.

Excessively low speeds impose a heavy load.

•DO NOT tamper with governed speed.

•DO NOT modify water pump in any way.

•DO NOT allow unqualified persons or children to operate or service water pump.

NOTICE

Improper treatment of water transfer pump can damage it and shorten its life.

•If you have questions about intended use, ask dealer or contact qualified service center.

•Be sure pump chamber is filled with water before starting the engine. Never run pump without priming.

•Use a non-collapsible hose on the suction side of pump.

•Use water pump only for intended uses.

•Pumping sea water, beverages, acids, chemical solutions, or any other liquid that promotes corrosion can damage the pump.

•Ensure all connections are air tight.

•DO NOT obstruct the suction or discharge hose in any way.

•NEVER operate pump without strainer basket connected to end of suction hose.

•DO NOT exceed suction head maximum of 8m (25 ft.) and total head of 32m (106 ft.). Use shortest suction head possible (see page 10).

•NEVER allow vehicles to drive over hoses. If a hose must be positioned across a roadway, use planking on each side of hose to allow vehicles to pass over without obstructing or collapsing hose.

•Anchor pump to avoid “walking” or equipment movement, especially if located near a ditch or edge of open ravine. The equipment could fall in.

•Keep equipment away from edge of river or lake where it could cause the bank to collapse.

•DO NOT insert any objects through cooling slots.

•NEVER operate units with broken or missing parts, or without protective housing or covers.

•DO NOT by-pass any safety device on this machine.

•NEVER move machine by pulling on hoses. Use frame on unit.

•Check fuel system for leaks or signs of deterioration, such as chafed or spongy hose, loose or missing clamps, or damaged tank or cap. Correct all defects before operating water transfer pump.

•This equipment is designed to be used with Briggs & Stratton Power Products authorized parts ONLY. If equipment is used with parts that DO NOT comply with minimum specifications, user assumes all risks and liabilities.

6

BRIGGSandSTRATTON.COM

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Operator’s Manual Engine Where to Find UsWater Transfer Pump Date PurchasedTable of Contents Hazard Symbols and Meanings Operator SafetySafety Rules Equipment DescriptionUnintentional sparking can result in fire or electric shock Contact with muffler area can result in serious burns Attach Anti-Vibration Pads AssemblyUnpack Water Transfer Pump Add Engine OilHigh Altitude When Adding FuelAttach Suction Hose At altitudes over 5,000 feet 1524 meters, a minimumConnect Discharge Hose Optional Attach Suction Hose to Strainer BasketFeatures and Controls Pump Chamber Be sure to fill with water before startingHJ K L M N PR S Operation Safe Operating ConsiderationsMove Water Pump to Safe Operating Location Feet 8m Discharge HeadFeet 25m Maximum Remove priming plug from top of pumpStarting the Water Pump Broken bones, fractures, bruises, or sprains could resultStopping the Water Pump Drain and Flush Water PumpReplace both plugs and finger tighten Maintenance Maintenance ScheduleWater Pump Maintenance Oil Oil Recommendations Engine MaintenanceCleaning Checking Oil LevelChanging Engine Oil Service Air CleanerTo service the air cleaner, follow these steps Loosen screw D and tilt cover E downService Spark Plug Clean Spark Arrester ScreenAir Cooling System Storage Troubleshooting Problem Cause CorrectionEmissions Control System Warranty Owner’s Warranty ResponsibilitiesWarranties Maintenance Emission InformationClaims and Coverage Exclusions Limited Warranty Model Product SpecificationsCommon Service Parts Maximum HeadManual del Operario Motor Dónde encontrarnosBomba de Transferencia de Agua Fecha de compraMontaje Resolución de Problemas GarantíasSeguridad de Operario Características y mandos OperandoReglas de seguridad Seguridad de OperarioDescripción del equipo ABC DEFCuando Ponga EN Funcionamiento EL Equipo Cuando Pruebe LA Bujía DEL MotorCuando Anada Combustible O Vacíe EL Depósito Cuando Opere EL EquipoAviso Agregar aceite al motor MontajeFijación de los soportes antivibración Agregue combustibleConexión de la manguera de aspiración a la bomba Fijación de la manguera de aspiraciónGran altitud Cuando Anada Combustible EL DepósitoConexión de la manguera de descarga opcional Conexión de la manguera a la cesta del filtroCaracterísticas y mandos Arrancador de retroceso Permite arrancar el motorNo mostrado Espacio libre y circulación de aire OperandoConsideraciones para un uso seguro ¿Qué es la altura total?Colocación de la cesta del filtro en la fuente de agua Quite el tapón de la parte superior de la bombaPuesta en marcha de la bomba de transferencia de agua Mueva la palanca estranguladora D hasta la posiciónMueva poco a poco la palanca estranguladora hacia la Parada de la bomba de transferencia de agua Vaciado y limpieza de la bomba de transferencia de aguaEl motor podría petardear, incendiarse o dañarse Mantenimiento del bomba de transferencia de agua MantenimientoPlan de mantenimiento Recomendaciones generalesAceite Recomendaciones sobre el aceite Mantenimiento del motorLimpieza Comprobación del nivel de aceitePara revisar el filtro de aire, siga estos pasos Cambio de aceite del motorRevisión del filtro de aire Afloje el tornillo D y quite la cubierta ELimpieza de la pantalla apagachispas AlmacenamientoRevisión de la bujía Sistema de refrigeración de aireBomba de transferencia de agua Proteja el sistema de combustibleAceite el diámetro interior del cilindro Otras sugerencias para el almacenamientoResolución de Problemas Garantía del sistema de control de emisiones Responsabilidades de la garantía del propietarioInformación sobre emisiones Garantía Limitada Especificaciones del producto Servicio común despideModelo Manuel d’utilisation Moteur Où nous trouverPompe de transfert d’eau Date d’achatAssemblage Fonctions et commandes OpérationSécurité de l’opérateur EntretienDescription de l équipement Symboles de danger et moyensSécurité de l’opérateur Règles de sécuritéUnintentional peut résulter dans feu ou électrique Avis Fixation des tampons anti-vibrations AssemblageDéballage du pompe de transfert d’eau Ajoutez de lhuile à moteurAltitude élevée Fixation du boyau daspirationÉvitez d’endommager le pompe de transfert d’eau Branchement du boyau daspiration à la pompeBranchement du boyau dévacuation facultatif Fixation du boyau daspiration au panier-filtreFonctions et commandes Pour un fonctionnement sécuritaire Déplacement de la pompe vers un emplacement sécuritaireOpération Dégagements et mouvement de lairEnlevez le bouchon fixé sur le dessus de la pompe Amorçage de la pompe de transfert d’eauLocalisation du panier-filtre dans la source deau Replacez le bouchon de la pompeDémarrage de la pompe de transfert d’eau Suivez les directives de démarrage suivantesArrêt de la pompe de transfert d’eau Vidange et rinçage de la pompe de transfert d’eauEntretien Calendrier dentretienEntretien du pompe de transfert d’eau Vérification du niveau dhuile Huile Recommandations relatives à l’huileEntretien du moteur Ajout d’huilePour faire lentretien du filtre à air, procédez comme suit Essuyez tout déversement dhuileEntretien du filtre à air Dévissez la vis D et ouvrez le couvercle ENettoyage de lécran pare-étincelles Installez la bougie dallumage et serrez-la solidementEntretien de la bougie dallumage Système de refroidissement à airEntreposage Dépannage Garanties Garantie du dispositif antipollutionResponsabilités de la garantie du propriétaire Réclamations et exclusions de couverture Durée de la couvertureAucun frais EntretienGarantie Limitée Caractéristiques du produit Pièces d’entretien courantModèle

Water Transfer Pump specifications

The Briggs & Stratton Water Transfer Pump is an essential tool designed for a variety of water transfer applications, combining efficiency with reliability. This powerhouse is ideal for homeowners, landscapers, and contractors who need to move large volumes of water for tasks like draining pools, emptying flooded basements, or irrigating gardens.

One of the standout features of the Briggs & Stratton Water Transfer Pump is its robust engine. The pump typically utilizes a dependable, four-stroke gas engine that provides superior power and fuel efficiency. With a reliable starting system, users can count on it to start quickly and run smoothly, even during extended use. This ensures that no time is wasted when water needs to be moved promptly.

In terms of performance, the water transfer pump is designed to handle significant volumes of water, often capable of transferring up to 3,000 gallons per hour. This impressive flow rate makes it suitable for both small-scale residential needs and larger commercial projects. The pump's lightweight and portable design allows users to easily transport it to various job sites, enhancing its versatility.

The pump's design incorporates a durable, corrosion-resistant construction, ensuring longevity even when exposed to harsh conditions. This resilience is critical for maintaining performance over time, particularly when dealing with muddy or sediment-filled water. Additionally, many models feature a convenient carrying handle, making it even easier to transport from one location to another.

Another significant aspect of the Briggs & Stratton Water Transfer Pump is its user-friendly interface. With intuitive controls, operators can quickly adjust settings and monitor performance without extensive technical knowledge. This focus on ease of use, combined with comprehensive safety features, helps ensure a safe and efficient operation every time.

Moreover, the pump often comes equipped with a variety of hose fittings and attachments, allowing users to customize it for specific tasks. The efficient pump mechanism, combined with these features, makes it an impressive option for all water transfer needs.

In summary, the Briggs & Stratton Water Transfer Pump stands out due to its powerful engine, impressive water-moving capacity, durable construction, portability, and user-friendly design. It's an indispensable tool for anyone needing to move water efficiently and effectively. Whether for landscaping, construction, or managing water in residential settings, this pump provides reliability you can trust.
Top Page Image Contents