Briggs & Stratton Assembly, Unpack Water Transfer Pump, Attach Anti-Vibration Pads, Add Fuel

Page 7

Assembly

Read entire operator’s manual before you attempt to assemble or operate your new water transfer pump.

Your water transfer pump requires some assembly and is ready for use after it has been properly serviced with the recommended oil and fuel.

If you have any problems with the assembly of your water transfer pump, please call the water transfer pump helpline at (800) 743-4115. If calling for assistance, please have the model, revision, and serial number from the data tag available. See Controls section for data tag location.

Unpack Water Transfer Pump

1.Remove the parts bag, accessories, and inserts included with water transfer pump.

2.Open carton completely by cutting each corner from top to bottom.

3.Ensure you have all included items prior to assembly.

Items in the carton include:

• Water pump

• Oil bottle

• Parts bag (which includes the following):

•This operator’s manual

•Owner’s registration card

•Strainer basket and barb

•Hose barb (2)

•Barb cuff (2)

•Rubber seal (2)

•Hose clamp (3)

•Anti-vibration kit

•Anti-vibration pad (4)

•Bolt (4)

•Washer (4)

•Lock nut (4)

•Instruction sheet

To prepare your water transfer pump for operation, you will need to perform these tasks:

1.Fill out and send in registration card.

2.Attach anti-vibration pads.

3.Add oil to engine crankcase.

4.Add fuel to fuel tank.

5.Attach suction hose.

6.Connect discharge hose (optional).

7.Move water pump to safe operating location.

8.Prime the water pump.

9.Locate strainer basket into water source.

Attach Anti-Vibration Pads

You will need the following tools to install the anti-vibration pads:

•10mm wrench

•Socket wrench with a 10mm socket

Attach anti-vibration pads to water pump as shown on instruction sheet included with anti-vibration kit.

IMPORTANT: You must attach anti-vibration pads prior to adding engine oil and fuel.

Add Engine Oil

1.Place water transfer pump on a flat, level surface.

2.Clean area around oil fill and remove yellow oil fill cap .

NOTE: See Oil Recommendations in Maintenance section. Verify provided oil bottle is the correct viscosity for current ambient temperature.

3.Using oil funnel (optional), slowly pour contents of provided oil bottle into oil fill opening.

NOTICE

Improper treatment of water transfer pump can damage it and shorten its life.

•DO NOT attempt to crank or start the engine before it has been properly serviced with the recommended oil. This may result in an engine failure.

4. Replace oil fill cap and fully tighten.

Add Fuel

Fuel must meet these requirements:

•Clean, fresh, unleaded gasoline.

•A minimum of 87 octane/87 AKI (91 RON). High altitude use, see High Altitude.

•Gasoline with up to 10% ethanol (gasohol) or up to 15% MTBE (methyl tertiary butyl ether) is acceptable.

NOTICE

Avoid water transfer pump damage.

Failure to follow Operator’s Manual for fuel recommendations voids warranty.

•DO NOT use unapproved gasoline such as E85.

•DO NOT mix oil in gasoline.

•DO NOT modify engine to run on alternate fuels.

To protect the fuel system from gum formation, mix in a fuel stabilizer when adding fuel. See Storage. All fuel is not the same. If you experience starting or performance problems after using fuel, switch to a different fuel provider or change brands. This engine is certified to operate on gasoline. The emission control system for this engine is EM (Engine Modifications).

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Operator’s Manual Date Purchased Where to Find UsWater Transfer Pump EngineTable of Contents Equipment Description Operator SafetySafety Rules Hazard Symbols and MeaningsUnintentional sparking can result in fire or electric shock Contact with muffler area can result in serious burns Add Engine Oil AssemblyUnpack Water Transfer Pump Attach Anti-Vibration PadsAt altitudes over 5,000 feet 1524 meters, a minimum When Adding FuelAttach Suction Hose High AltitudeAttach Suction Hose to Strainer Basket Connect Discharge Hose OptionalPump Chamber Be sure to fill with water before starting Features and ControlsHJ K L M N PR S Safe Operating Considerations OperationMove Water Pump to Safe Operating Location Remove priming plug from top of pump Discharge HeadFeet 25m Maximum Feet 8mBroken bones, fractures, bruises, or sprains could result Starting the Water PumpDrain and Flush Water Pump Stopping the Water PumpReplace both plugs and finger tighten Maintenance Schedule MaintenanceWater Pump Maintenance Checking Oil Level Engine MaintenanceCleaning Oil Oil RecommendationsLoosen screw D and tilt cover E down Service Air CleanerTo service the air cleaner, follow these steps Changing Engine OilClean Spark Arrester Screen Service Spark PlugAir Cooling System Storage Problem Cause Correction TroubleshootingOwner’s Warranty Responsibilities Emissions Control System WarrantyWarranties Emission Information MaintenanceClaims and Coverage Exclusions Limited Warranty Maximum Head Product SpecificationsCommon Service Parts ModelManual del Operario Fecha de compra Dónde encontrarnosBomba de Transferencia de Agua MotorCaracterísticas y mandos Operando Resolución de Problemas GarantíasSeguridad de Operario MontajeABC DEF Seguridad de OperarioDescripción del equipo Reglas de seguridadCuando Opere EL Equipo Cuando Pruebe LA Bujía DEL MotorCuando Anada Combustible O Vacíe EL Depósito Cuando Ponga EN Funcionamiento EL EquipoAviso Agregue combustible MontajeFijación de los soportes antivibración Agregar aceite al motorCuando Anada Combustible EL Depósito Fijación de la manguera de aspiraciónGran altitud Conexión de la manguera de aspiración a la bombaConexión de la manguera a la cesta del filtro Conexión de la manguera de descarga opcionalArrancador de retroceso Permite arrancar el motor Características y mandosNo mostrado ¿Qué es la altura total? OperandoConsideraciones para un uso seguro Espacio libre y circulación de aireQuite el tapón de la parte superior de la bomba Colocación de la cesta del filtro en la fuente de aguaMueva la palanca estranguladora D hasta la posición Puesta en marcha de la bomba de transferencia de aguaMueva poco a poco la palanca estranguladora hacia la Vaciado y limpieza de la bomba de transferencia de agua Parada de la bomba de transferencia de aguaEl motor podría petardear, incendiarse o dañarse Recomendaciones generales MantenimientoPlan de mantenimiento Mantenimiento del bomba de transferencia de aguaComprobación del nivel de aceite Mantenimiento del motorLimpieza Aceite Recomendaciones sobre el aceiteAfloje el tornillo D y quite la cubierta E Cambio de aceite del motorRevisión del filtro de aire Para revisar el filtro de aire, siga estos pasosSistema de refrigeración de aire AlmacenamientoRevisión de la bujía Limpieza de la pantalla apagachispasOtras sugerencias para el almacenamiento Proteja el sistema de combustibleAceite el diámetro interior del cilindro Bomba de transferencia de aguaResolución de Problemas Responsabilidades de la garantía del propietario Garantía del sistema de control de emisionesInformación sobre emisiones Garantía Limitada Servicio común despide Especificaciones del productoModelo Manuel d’utilisation Date d’achat Où nous trouverPompe de transfert d’eau MoteurEntretien Fonctions et commandes OpérationSécurité de l’opérateur AssemblageRègles de sécurité Symboles de danger et moyensSécurité de l’opérateur Description de l équipementUnintentional peut résulter dans feu ou électrique Avis Ajoutez de lhuile à moteur AssemblageDéballage du pompe de transfert d’eau Fixation des tampons anti-vibrationsBranchement du boyau daspiration à la pompe Fixation du boyau daspirationÉvitez d’endommager le pompe de transfert d’eau Altitude élevéeFixation du boyau daspiration au panier-filtre Branchement du boyau dévacuation facultatifFonctions et commandes Dégagements et mouvement de lair Déplacement de la pompe vers un emplacement sécuritaireOpération Pour un fonctionnement sécuritaireReplacez le bouchon de la pompe Amorçage de la pompe de transfert d’eauLocalisation du panier-filtre dans la source deau Enlevez le bouchon fixé sur le dessus de la pompeSuivez les directives de démarrage suivantes Démarrage de la pompe de transfert d’eauVidange et rinçage de la pompe de transfert d’eau Arrêt de la pompe de transfert d’eauCalendrier dentretien EntretienEntretien du pompe de transfert d’eau Ajout d’huile Huile Recommandations relatives à l’huileEntretien du moteur Vérification du niveau dhuileDévissez la vis D et ouvrez le couvercle E Essuyez tout déversement dhuileEntretien du filtre à air Pour faire lentretien du filtre à air, procédez comme suitSystème de refroidissement à air Installez la bougie dallumage et serrez-la solidementEntretien de la bougie dallumage Nettoyage de lécran pare-étincellesEntreposage Dépannage Garantie du dispositif antipollution GarantiesResponsabilités de la garantie du propriétaire Entretien Durée de la couvertureAucun frais Réclamations et exclusions de couvertureGarantie Limitée Pièces d’entretien courant Caractéristiques du produitModèle

Water Transfer Pump specifications

The Briggs & Stratton Water Transfer Pump is an essential tool designed for a variety of water transfer applications, combining efficiency with reliability. This powerhouse is ideal for homeowners, landscapers, and contractors who need to move large volumes of water for tasks like draining pools, emptying flooded basements, or irrigating gardens.

One of the standout features of the Briggs & Stratton Water Transfer Pump is its robust engine. The pump typically utilizes a dependable, four-stroke gas engine that provides superior power and fuel efficiency. With a reliable starting system, users can count on it to start quickly and run smoothly, even during extended use. This ensures that no time is wasted when water needs to be moved promptly.

In terms of performance, the water transfer pump is designed to handle significant volumes of water, often capable of transferring up to 3,000 gallons per hour. This impressive flow rate makes it suitable for both small-scale residential needs and larger commercial projects. The pump's lightweight and portable design allows users to easily transport it to various job sites, enhancing its versatility.

The pump's design incorporates a durable, corrosion-resistant construction, ensuring longevity even when exposed to harsh conditions. This resilience is critical for maintaining performance over time, particularly when dealing with muddy or sediment-filled water. Additionally, many models feature a convenient carrying handle, making it even easier to transport from one location to another.

Another significant aspect of the Briggs & Stratton Water Transfer Pump is its user-friendly interface. With intuitive controls, operators can quickly adjust settings and monitor performance without extensive technical knowledge. This focus on ease of use, combined with comprehensive safety features, helps ensure a safe and efficient operation every time.

Moreover, the pump often comes equipped with a variety of hose fittings and attachments, allowing users to customize it for specific tasks. The efficient pump mechanism, combined with these features, makes it an impressive option for all water transfer needs.

In summary, the Briggs & Stratton Water Transfer Pump stands out due to its powerful engine, impressive water-moving capacity, durable construction, portability, and user-friendly design. It's an indispensable tool for anyone needing to move water efficiently and effectively. Whether for landscaping, construction, or managing water in residential settings, this pump provides reliability you can trust.
Top Page Image Contents