KitchenAid W10379132A manual Install Anti-Tip Boards, Connect the Water Supply

Page 21

42" (106.7 cm) Models

2.Place pieces of the shipping carton on the floor when rolling the dolly and refrigerator into the house. Move the refrigerator close to the built-in opening.

3.Place top of cardboard carton or plywood under refrigerator.

4.Stand the refrigerator up. First, place the left bottom edge of the refrigerator on the floor, stand the refrigerator upright and then lower the right-hand side of the refrigerator to the floor.

5.Do not remove film or cover.

6.Reassemble the trim and top grille after the dolly has been removed from the refrigerator.

Install Anti-Tip Boards

IMPORTANT:

■To avoid tipping during use, the solid soffit must be within

1" (2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1" (2.5 cm) or one is not available, then the refrigerator must be braced.

■It is recommended that board(s) be installed before the refrigerator is installed.

■Board(s) must be long enough to fully cover the width of the compressor cover.

■Locate the board(s) so the bottom surface(s) of the board(s) is(are) 84" (213 cm) from the floor.

■During installation, raise the refrigerator up so there is

¹⁄₄" (6.35 mm) maximum between the top of the refrigerator and the bottom of the anti-tip board(s). Do not crush the compressor cover when raising the rear leveling legs.

To Install Anti-tip Boards

1.Mark the stud locations on rear wall 80" to 90" (203 cm to 229 cm) above floor.

2.Securely attach one or two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards to wall studs behind refrigerator. Use six #8 x 3" (7.6 cm) (or longer) wood screws. The wood screws must be screwed into the studs at least 1½" (3.8 cm). The board(s) must overlap the compressor cover.

A B

C

2" (5 cm)

D

A. Center board ¹⁄₄" (6.35 mm) max. above refrigerator

B. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards

C. Attach to studs with six #8 x 3" (7.6 cm) screws

D. Compressor cover

Connect the Water Supply

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line is connected, turn the ice maker OFF.

Connect to Water Line

Parts Needed:

■Minimum 7 ft (2.13 m) flexible, codes approved water supply line

Style 1 - Shutoff Valve Connection

NOTE: If your water line connection does not look like Style 1, see “Style 2 - Copper Line Connection.”

1.Unplug refrigerator or disconnect power supply.

IMPORTANT: Before attaching the tubing to shutoff valve, flush the main water supply line to remove particles and air in the water line. Allow enough flow so that water becomes clear. Flushing the water line may help avoid filters and/or water valves from becoming clogged.

2.Connect the flexible, codes approved water supply line to the water shutoff valve by threading the provided nut onto the shutoff valve as shown.

NOTE: The shutoff valve shown is in the side cabinet as recommended.

A

B

C

A.Bulb

B.Nut

C.Water tubing

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents BOTTOM-MOUNT BUILT-IN Refrigerator Table of Contents/Índice/Table des matièresTable of Contents ÍndiceTable DES Matières Your safety and the safety of others are very important Refrigerator SafetyArchitect Series 36 91.4 cm Models ModelsClassic Series 36 91.4 cm Models Overlay Series 36 91.4 cm ModelsOpening Dimensions Installation RequirementsTools and Parts Location RequirementsElectrical Requirements Dimension BRecommended Grounding Method ModelTipping Radius Water Supply RequirementsSide View Product DimensionsTop View 36 91.4 cm Models 42 106.7 cm ModelsDoor Swing Dimensions Hinge CabinetrySpacer Panel Panel 90˚ Door Stop Position HingeOverlay Panel 90˚ Door Stop Position Hinge Overlay Series Custom Panels Custom Overlay Panel DimensionsCustom Overlay Panels 36 91.4 cm Models Custom Backer Panels 36 91.4 cm ModelsSpacer Panels All models Piece Overlay Panel ConfigurationTop View Side ViewClassic Series Custom Panels 36 91.4 cm Models Classic and Architect Series Custom Side Panels Refrigerator and Side Trim DimensionsDoor Panel Routing Requirements RefrigeratorOverlay Series Custom Side Panels Recessed Inset Installation Dimensions 36 91.4 cm Models Side Trim 36 91.4 cm Models Inset Installation DimensionsRefrigerator 42 106.7 cm Models Side Trim 42 106.7 cm ModelsUnpack the Refrigerator Installation InstructionsReduce Tipping Radius Move the Refrigerator into HouseTo Install Anti-tip Boards Install Anti-Tip BoardsConnect the Water Supply Connect to Water Line Parts NeededStyle 2 Copper Line Connection Parts SuppliedConnect to Refrigerator Connections including connections at the valve that leakPlug in Refrigerator Move Refrigerator to Final LocationLevel and Align Refrigerator Door Panel Installation Install Overlay and Classic Series Custom PanelsAdjust Doors Door Height Adjustment 42 106.7 cm ModelsDoor Alignment 36 91.4 cm Models Door Swing Adjustment 36 91.4 cm Models Hold the door open to a position that is less thanDoor stop is located on the top hinge 110 Install Side PanelComplete Installation Install Base GrilleSu seguridad y la seguridad de los demás es muy importante Seguridad DEL RefrigeradorSerie Architect modelos de 36 91,4 cm ModelosSerie Classic modelos de 36 91,4 cm Serie Overlay modelos de 36 91,4 cmPiezas y herramientas Requisitos DE InstalaciónRequisitos de ubicación Medidas de la aberturaRequisitos eléctricos Método de conexión a tierra recomendadoModelo Ancho a Medida B Como se muestra Anteriormente Arco de vuelco Requisitos del suministro de aguaVista lateral Medidas del productoVista superior Modelos de 36 91,4 cm Modelos de 42 106,7 cmMedidas de oscilación de la puerta Panel espaciador Armarios BisagraRecubierto Puerta Posición de retención de la puerta de 90˚ Bisagra Puerta SoporteRecubierto Panel espaciador Paneles a la medida de la Serie Overlay Dimensiones del panel recubierto a la medidaPaneles espaciadores todos los modelos Configuración del panel recubierto con puerta de 1 piezaVista superior Vista lateralPanel de la rejilla superior Juegos de extensión de agarraderas de la puertaPaneles del refrigerador y del congelador Requisitos de contorneado del panel de la rejilla superiorMedidas del refrigerador y del adorno lateral Requisitos de contorneado de los paneles de la puertaPanel de la puerta Vista lateral Agarradera extendida Vista superiorPaneles laterales a la medida para la Serie Overlay Adorno lateral modelos de 42 106,7 cm Refrigerador modelos de 42 106,7 cmDesempaque el refrigerador Instrucciones DE InstalaciónCómo reducir el arco de vuelco Cómo hacer entrar el refrigerador en la casaConexión del suministro de agua Cómo instalar los tableros antivuelcoCómo instalar los tableros antivuelco Conexión a la línea de agua Piezas necesariasEstilo 2 Conexión de la tubería de cobre Conexión al refrigeradorPiezas suministradas Cómo mover el refrigerador a Su ubicación final Cómo enchufar el refrigeradorNivelación y alineamiento del refrigerador Instalación del panel de la puerta Paneles Alineamiento de la puerta modelos de 36 91,4 cm Cómo ajustar las puertasCómo ajustar la altura de la puerta modelos de 42 106,7 cm Quite la placa de fijación, como se muestraCómo instalar el panel lateral Cómo instalar la rejilla de la base Cómo terminar la instalaciónClave el borde trasero del panel al tablero de soporte Votre sécurité et celle des autres est très importante Sécurité DU RéfrigérateurSérie Architect modèles de 36 91,4 cm ModèlesSérie Overlay modèles de 36 91,4 cm Série Classic modèles de 36 91,4 cmExigences d’emplacement Exigences ’INSTALLATIONDimensions de l’ouverture Outillage et piècesSpécifications électriques Méthode recommandée de mise à la terreRayon de basculement Spécifications de l’alimentation en eauPression de leau Alimentation en eau par osmose inverseVue latérale Dimensions du produitVue de dessus Modèles de 36 91,4 cm Modèles de 42 106,7 cmDimensions pour le pivotement des portes Charnière Placard Panneau’espacement Panneau Séparation De séparation Panneaux personnalisés de la série Overlay Panneaux personnalisés DimensionsPanneaux de séparation Tous modèles Configuration pour panneau Overlay monopièceVue de dessus Vue latéraleEnsembles de poignées de porte prolongées Ensembles de panneaux doriginePanneau de la grille supérieure Panneaux du réfrigérateur et du congélateurDimensions du réfrigérateur et des garnitures latérales Exigences dusinage des panneaux de portePanneau de porte Vue latérale Panneaux latéraux personnalisés de La série Overlay Garnitures latérales modèles de 42 106,7 cm Réfrigérateur modèles de 42 106,7 cmDéballage du réfrigérateur Instructions D’INSTALLATIONRéduction du rayon de basculement Faire entrer le réfrigérateur dans le domicileInstallation des planches antibasculement Installation de planches antibasculementRaccordement à lalimentation en eau Raccordement à la canalisation deau Pièces nécessairesRaccordement au réfrigérateur Pièces fourniesStyle 2 Raccordement de la canalisation d’eau en cuivre Déplacement du réfrigérateur à Lemplacement final Brancher le réfrigérateurRéglage de laplomb et alignement Du réfrigérateur Installation des panneaux de porte Panneaux Ajustement de la des portes Alignement des portes modèles de 36 91,4 cmRéglage de la hauteur de la porte modèles de 42 106,7 cm Installation du panneau latéral Achever l’installation Installation de la grille de la baseClouer la rive arrière du panneau sur la planche dappui W10379132A

W10379132A specifications

The KitchenAid W10379132A is a versatile kitchen appliance that enhances culinary experiences through a blend of functionality and innovative design. This attachment is primarily compatible with KitchenAid stand mixers, allowing users to maximize their mixer’s potential by embracing new culinary techniques.

One of the standout features of the W10379132A is its ability to mix, knead, and whip ingredients with ease. It includes a powerful motor and a robust construction that can handle a variety of doughs, from bread to cookie mixtures, ensuring consistent results every time. The motor is designed to minimize noise while providing ample power, so chefs can enjoy a more pleasant cooking experience without compromising on performance.

The attachment also boasts a range of innovative technologies that simplify food preparation. With its adjustable speed settings, users can precisely control the mixing process, allowing for both gentle folding and vigorous stirring, depending on the recipe requirements. This flexibility makes it suitable for both home cooks and professional chefs alike.

Durability is another essential characteristic of the KitchenAid W10379132A. Constructed from high-quality materials, the attachment is designed to withstand the rigors of frequent use. Its seamless design makes cleaning a breeze, as it can be easily detached and washed, either by hand or in a dishwasher, ensuring that hygiene is maintained effortlessly.

Additionally, the W10379132A is equipped with a user-friendly design that makes it easy for anyone to use. The ergonomic handle allows for comfortable handling, while the clearly marked attachments facilitate quick changes between mixing and other culinary tasks. This attention to user experience ensures that both novice cooks and seasoned chefs can achieve excellent results without frustration.

In summary, the KitchenAid W10379132A is more than just a mixer attachment; it is an essential tool for anyone looking to elevate their cooking. With its combination of power, durability, and ease of use, this attachment ensures that culinary creativity can thrive in any kitchen setting. Its myriad features and thoughtful design make it a valuable addition for creating a wide array of delicious dishes with confidence and efficiency.
Top Page Image Contents