KitchenAid KESC300H, KESH307H, KESC307H manual Line

Page 16

NOTE: Do not loosen the factory-installed nuts on the terminal block when you perform the following steps.

4.Connect the neutral (white) wire of the power supply cord to the center, silver-

colored terminal screw on the terminal block, and secure it with one of the 3/8″ brass nuts that you set aside earlier.

5.Connect the remaining two power supply

cord wires to the outer terminals of the terminal block, and secure them with 3/8″ brass nuts.

6.Tighten the strain relief screws to secure the power supply cord.

7.Install the terminal block cover.

silver-colored terminal block screw

neutral wire (center wire)

green ground wire

U.L. listed strain relief and 40-ampere range power supply cord

3-Wire Electrical Connection

Use this method only if local codes permit con- necting a cabinet-grounded conductor to the neutral wire of the power supply cord.

NOTE: Do not loosen the factory-installed nuts on the terminal block when you perform the following steps.

1.Connect the neutral (white) wire of the power supply cord to the center, silver-

colored terminal screw on the terminal block, and secure it with one of the 3/8″ brass nuts that you set aside earlier.

2.Connect the remaining two power supply

cord wires to the outer terminals of the terminal block, and secure them with 3/8″ brass nuts.

3.Tighten the strain relief screws to secure the power supply cord.

4.Install the terminal block cover.

silver-colored terminal block screw

	line 2
ground	neutral
link	(center wire)
line 1	U.L.-listed strain relief
	U.L.-listed strain relief
	and 40-ampere range
	power supply cord

2-4

Image 16

Contents SELF-CLEANING SLIDE-IN Electric Range Forward Goals and ObjectivesTable of Contents Wiring Diagram & Strip Circuits Safety First GeneralElectrostatic Discharge ESD Sensitive Electronics Model Number Kitchenaid Model & Serial Number DesignationsSerial Number Model & Serial Number Label Location Model & Serial Number Location Located Behind Storage DrawerSpecifications KESC300H WH/BL/BT KESC307H WH/BT/BS KESH307H WH/BL/BSInterior Kitchenaid Electric Range Warranty Limited WarrantyPage Electrical Supply Requirements GeneralElectrical Connections Not used for Canadian Installations Power Supply Cord Connection Wire Electrical ConnectionLine Direct Wire Connection Ground link Screw Line Moving the Range Theory of Operation AIR Flow Rear PanelCooling FAN AIR Flow AIR Inlets Under Control PanelInset #2 Bimetal SwitchesInset #1 Surface Element Limiter Door Lock Solenoid & Door Latch Switch Door Lock Solenoid Door UnlockedHOW the SELF-CLEAN Cycle Works After 30 Minutes of CleanComponent Access Component LocationsTo remove an infinite switch To remove the control panelTo remove a bimetal switch To remove an indicator light Removing the Electronic Oven Control AN Indicator LightTo remove the electronic oven control To remove an element and limiter On the nextTo remove the hot surface indicator assembly Removing the Cooktop Glass Lower the cooktop Lift Grate Off Cooktop Rear Trim Rear Trim Tension Brackets Removing the Door Latch Assembly Door Switch To remove the door latch assemblyTo remove the door switch To remove the dual broil element Removing the Dual Broil Element Hidden Bake ElementTo remove the hidden bake element Element Shield Screw Element Wires Removing the Convection Bake Element & FAN Motor To remove the convection bake ele- mentTo remove the convection fan motor Removing AN Oven Light Socket Assembly Removing the Meat Probe Jack Removing the Oven Temperature Sensor Removing a Side Panel To remove the double line break DLB relay Removing the Double Line Break DLB Relay Cooling FAN MotorTo remove the cooling fan motor Remove This Screw Loosen These Screws Housing To reinstall the oven door Removing the Oven DoorTo remove the door handle To remove the decorative glassTo remove a hinge To remove the inner and outer oven door glass Removing the Oven Door Gasket Page Component Testing Bimetal SwitchSingle Element Infinite Switches Dual Element Infinite Switch Optional Surface Elements & Limiters To test the left front LF dual element and limiterTo test the RF, LR, & RR single ele- ments & limiters Door Switch N.O To test the door latch switchHidden Bake Element Dual Broil ElementConvection Bake Element Convection FAN MotorOven Temperature Sensor Cooling FAN MotorDouble Line Break DLB Relay Diagnosis & Troubleshooting DiagnosisFault Error Code Charts Fault Error F1E3Troubleshooting Charts Problem Possible Cause SolutionProblem Possible Cause Solution Problem Possible Cause Solution Oven Temperature Calibration Wiring Diagram & Strip Circuits Wiring Diagram #9753028, REV. BPage Clean Strip CircuitsBake Including PRE-HEAT Broil EconoDriving Circuit Convection BroilOven Light Optional Halogen Oven Lights OptionalPage Product Specifications Warranty Information Sources