KitchenAid KESH307H, KESC300H, KESC307H manual Removing the Oven Door, To reinstall the oven door

Page 48

REMOVING THE OVEN DOOR

1.To remove the oven door, open the door to its first stop.

2.Grasp the sides of the door, lift it slightly, and pull the door forward until the hinge hangers are partially out of the slots in the chassis. Do not completely remove the hinge hangers from the slots, since there will be spring tension on them.

Partially Remove

Door

3.Reposition the angle of the door to its vertical position to remove the spring ten- sion on the hinge hangers, then pull the hangers the rest of the way out of the chassis slots.

Hinge Hanger

Keep Door

Vertical

To reinstall the oven door:

1.Grasp the sides of the door and insert the hinge hangers into the hinge slots. Lift the door slightly and push in at the bottom until the hangers are fully installed in the unit. NOTE: If the hinge hangers are not seated properly, the door will not close tightly and may be off-center. To seat the hinge hang- ers, keep the door vertical, then lift it slightly, and push in on the bottom until the hangers are fully seated.

2.Open and close the oven door to make sure that it operates and seals properly.

4-22

Image 48

Contents SELF-CLEANING SLIDE-IN Electric Range Forward Goals and ObjectivesTable of Contents Wiring Diagram & Strip Circuits Safety First GeneralElectrostatic Discharge ESD Sensitive Electronics Kitchenaid Model & Serial Number Designations Model NumberSerial Number Model & Serial Number Label Location Model & Serial Number Location Located Behind Storage DrawerSpecifications KESC300H WH/BL/BT KESC307H WH/BT/BS KESH307H WH/BL/BSInterior Kitchenaid Electric Range Warranty Limited WarrantyPage Electrical Supply Requirements GeneralElectrical Connections Not used for Canadian Installations Power Supply Cord Connection Wire Electrical ConnectionLine Direct Wire Connection Ground link Screw Line Moving the Range Theory of Operation AIR Flow Rear PanelCooling FAN AIR Flow AIR Inlets Under Control PanelBimetal Switches Inset #2Inset #1 Surface Element Limiter Door Lock Solenoid & Door Latch Switch Door Lock Solenoid Door UnlockedHOW the SELF-CLEAN Cycle Works After 30 Minutes of CleanComponent Access Component LocationsTo remove an infinite switch To remove the control panelTo remove a bimetal switch Removing the Electronic Oven Control AN Indicator Light To remove an indicator lightTo remove the electronic oven control To remove an element and limiter On the nextTo remove the hot surface indicator assembly Removing the Cooktop Glass Lower the cooktop Lift Grate Off Cooktop Rear Trim Rear Trim Tension Brackets Removing the Door Latch Assembly Door Switch To remove the door latch assemblyTo remove the door switch Removing the Dual Broil Element Hidden Bake Element To remove the dual broil elementTo remove the hidden bake element Element Shield Screw Element Wires Removing the Convection Bake Element & FAN Motor To remove the convection bake ele- mentTo remove the convection fan motor Removing AN Oven Light Socket Assembly Removing the Meat Probe Jack Removing the Oven Temperature Sensor Removing a Side Panel Removing the Double Line Break DLB Relay Cooling FAN Motor To remove the double line break DLB relayTo remove the cooling fan motor Remove This Screw Loosen These Screws Housing To reinstall the oven door Removing the Oven DoorTo remove the decorative glass To remove the door handleTo remove a hinge To remove the inner and outer oven door glass Removing the Oven Door Gasket Page Component Testing Bimetal SwitchSingle Element Infinite Switches Dual Element Infinite Switch Optional Surface Elements & Limiters To test the left front LF dual element and limiterTo test the RF, LR, & RR single ele- ments & limiters Door Switch N.O To test the door latch switchHidden Bake Element Dual Broil ElementConvection Bake Element Convection FAN MotorOven Temperature Sensor Cooling FAN MotorDouble Line Break DLB Relay Diagnosis & Troubleshooting DiagnosisFault Error Code Charts Fault Error F1E3Troubleshooting Charts Problem Possible Cause SolutionProblem Possible Cause Solution Problem Possible Cause Solution Oven Temperature Calibration Wiring Diagram & Strip Circuits Wiring Diagram #9753028, REV. BPage Clean Strip CircuitsBake Including PRE-HEAT Broil EconoDriving Circuit Convection BroilOven Light Optional Halogen Oven Lights OptionalPage Product Specifications Warranty Information Sources