KitchenAid KESH307H, KESC300H, KESC307H manual Component Access, Component Locations

Page 27

COMPONENT ACCESS

This section instructs you on how to service each component inside the range. The range components and their locations are shown below.

COMPONENT LOCATIONS

Hot Surface Indicators

Door Latch Assembly

Element & Limiter

 

 

 

Indicator Light

 

Electronic Oven Control

 

 

Single Element

 

Cooling Fan

Infinite Switch

 

 

Bimetal Switch

 

 

Dual Element

 

Ambient Bimetal

Infinite Switch

 

 

Switch

 

 

Oven Light

 

 

 

 

Door Switch

Meat Probe Jack

 

Oven Temperature

 

 

Dual Broil

 

Sensor

 

 

Element

 

 

Convection Bake

 

 

Element & Fan Motor

 

 

Double Line

 

 

Break Relay

 

 

Cooling

 

Hidden Bake Element

Fan Motor

 

 

 

4-1

Image 27
Contents SELF-CLEANING SLIDE-IN Electric Range Goals and Objectives ForwardTable of Contents Wiring Diagram & Strip Circuits General Safety FirstElectrostatic Discharge ESD Sensitive Electronics Kitchenaid Model & Serial Number Designations Model NumberSerial Number Model & Serial Number Location Located Behind Storage Drawer Model & Serial Number Label LocationKESC300H WH/BL/BT KESC307H WH/BT/BS KESH307H WH/BL/BS SpecificationsInterior Limited Warranty Kitchenaid Electric Range WarrantyPage General Electrical Supply RequirementsElectrical Connections Not used for Canadian Installations Wire Electrical Connection Power Supply Cord ConnectionLine Direct Wire Connection Ground link Screw Line Moving the Range AIR Flow Rear Panel Theory of OperationAIR Inlets Under Control Panel Cooling FAN AIR FlowBimetal Switches Inset #2Inset #1 Surface Element Limiter Door Lock Solenoid Door Unlocked Door Lock Solenoid & Door Latch SwitchAfter 30 Minutes of Clean HOW the SELF-CLEAN Cycle WorksComponent Locations Component AccessTo remove the control panel To remove an infinite switchTo remove a bimetal switch Removing the Electronic Oven Control AN Indicator Light To remove an indicator lightTo remove the electronic oven control On the next To remove an element and limiterTo remove the hot surface indicator assembly Removing the Cooktop Glass Lower the cooktop Lift Grate Off Cooktop Rear Trim Rear Trim Tension Brackets To remove the door latch assembly Removing the Door Latch Assembly Door SwitchTo remove the door switch Removing the Dual Broil Element Hidden Bake Element To remove the dual broil elementTo remove the hidden bake element Element Shield Screw Element Wires To remove the convection bake ele- ment Removing the Convection Bake Element & FAN MotorTo remove the convection fan motor Removing AN Oven Light Socket Assembly Removing the Meat Probe Jack Removing the Oven Temperature Sensor Removing a Side Panel Removing the Double Line Break DLB Relay Cooling FAN Motor To remove the double line break DLB relayTo remove the cooling fan motor Remove This Screw Loosen These Screws Housing Removing the Oven Door To reinstall the oven doorTo remove the decorative glass To remove the door handleTo remove a hinge To remove the inner and outer oven door glass Removing the Oven Door Gasket Page Bimetal Switch Component TestingSingle Element Infinite Switches Dual Element Infinite Switch Optional To test the left front LF dual element and limiter Surface Elements & LimitersTo test the RF, LR, & RR single ele- ments & limiters To test the door latch switch Door Switch N.ODual Broil Element Hidden Bake ElementConvection FAN Motor Convection Bake ElementCooling FAN Motor Oven Temperature SensorDouble Line Break DLB Relay Diagnosis Diagnosis & TroubleshootingFault Error F1E3 Fault Error Code ChartsProblem Possible Cause Solution Troubleshooting ChartsProblem Possible Cause Solution Problem Possible Cause Solution Oven Temperature Calibration Wiring Diagram #9753028, REV. B Wiring Diagram & Strip CircuitsPage Broil Econo CleanStrip Circuits Bake Including PRE-HEATConvection Broil Driving CircuitHalogen Oven Lights Optional Oven Light OptionalPage Product Specifications Warranty Information Sources