KitchenAid KESC300H, KESH307H, KESC307H manual To remove an element and limiter, On the next

Page 31

REMOVING AN ELEMENT & LIMITER AND THE HOT SURFACE INDICATOR ASSEMBLY

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

1.Unplug range or disconnect power.

2.Remove the control panel from its subchassis, (see page 4-2 for the proce- dure), and rotate it forward onto the cooktop glass.

3.Remove the five screws and flat washer from the control panel subchassis.

5.To remove an element and limiter:

a)Remove the wires from the element and limiter terminals.

b)Remove the screw, or pull the end of the retaining rod out of the bracket, and remove the element and limiter from the bottom of the cooktop.

	2 Screws	Subchassis
	2 Screws	Screw & Flat Washer	2 Screws
			2 Screws

4.Move the control panel back into place over the chassis, then lift the front of the cooktop assembly, and prop it up with a piece of board so that you can access the components (see the photo at the top of the next column). CAUTION: Be careful that the cooktop does not accidentally fall.

Retaining Rod

(Pull Out)

Retaining

Rod Screws

4-5	Continued on the next page.

Image 31

Contents SELF-CLEANING SLIDE-IN Electric Range Goals and Objectives ForwardTable of Contents Wiring Diagram & Strip Circuits General Safety FirstElectrostatic Discharge ESD Sensitive Electronics Model Number Kitchenaid Model & Serial Number DesignationsSerial Number Model & Serial Number Location Located Behind Storage Drawer Model & Serial Number Label LocationKESC300H WH/BL/BT KESC307H WH/BT/BS KESH307H WH/BL/BS SpecificationsInterior Limited Warranty Kitchenaid Electric Range WarrantyPage General Electrical Supply RequirementsElectrical Connections Not used for Canadian Installations Wire Electrical Connection Power Supply Cord ConnectionLine Direct Wire Connection Ground link Screw Line Moving the Range AIR Flow Rear Panel Theory of OperationAIR Inlets Under Control Panel Cooling FAN AIR FlowInset #2 Bimetal SwitchesInset #1 Surface Element Limiter Door Lock Solenoid Door Unlocked Door Lock Solenoid & Door Latch SwitchAfter 30 Minutes of Clean HOW the SELF-CLEAN Cycle WorksComponent Locations Component AccessTo remove the control panel To remove an infinite switchTo remove a bimetal switch To remove an indicator light Removing the Electronic Oven Control AN Indicator LightTo remove the electronic oven control On the next To remove an element and limiterTo remove the hot surface indicator assembly Removing the Cooktop Glass Lower the cooktop Lift Grate Off Cooktop Rear Trim Rear Trim Tension Brackets To remove the door latch assembly Removing the Door Latch Assembly Door SwitchTo remove the door switch To remove the dual broil element Removing the Dual Broil Element Hidden Bake ElementTo remove the hidden bake element Element Shield Screw Element Wires To remove the convection bake ele- ment Removing the Convection Bake Element & FAN MotorTo remove the convection fan motor Removing AN Oven Light Socket Assembly Removing the Meat Probe Jack Removing the Oven Temperature Sensor Removing a Side Panel To remove the double line break DLB relay Removing the Double Line Break DLB Relay Cooling FAN MotorTo remove the cooling fan motor Remove This Screw Loosen These Screws Housing Removing the Oven Door To reinstall the oven doorTo remove the door handle To remove the decorative glassTo remove a hinge To remove the inner and outer oven door glass Removing the Oven Door Gasket Page Bimetal Switch Component TestingSingle Element Infinite Switches Dual Element Infinite Switch Optional To test the left front LF dual element and limiter Surface Elements & LimitersTo test the RF, LR, & RR single ele- ments & limiters To test the door latch switch Door Switch N.ODual Broil Element Hidden Bake ElementConvection FAN Motor Convection Bake ElementCooling FAN Motor Oven Temperature SensorDouble Line Break DLB Relay Diagnosis Diagnosis & TroubleshootingFault Error F1E3 Fault Error Code ChartsProblem Possible Cause Solution Troubleshooting ChartsProblem Possible Cause Solution Problem Possible Cause Solution Oven Temperature Calibration Wiring Diagram #9753028, REV. B Wiring Diagram & Strip CircuitsPage Broil Econo CleanStrip Circuits Bake Including PRE-HEATConvection Broil Driving CircuitHalogen Oven Lights Optional Oven Light OptionalPage Product Specifications Warranty Information Sources