KitchenAid KESH307H, KESC300H, KESC307H manual Removing a Side Panel

Page 45

REMOVING A SIDE PANEL

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

1.Unplug range or disconnect power.

2.Pull the range away from the wall so that you can access the rear of the unit.

3.Remove the oven door and set it aside (see page 4-22 for the procedure).

4.Pull the storage drawer out as far as it will go.

5.Remove the two rear screws from the side panel.

Screw

Side Panel

6.From the rear of the unit, reach inside and remove the screw from the bottom of the side panel.

Remove Bottom

Side Panel Screw

7.Slide the side panel forward and unhook the front edge, then tilt the top of the side panel out, and lift the panel from the unit.

Slide Forward & Tilt

Top Of Panel Out

Screw (Inside)

Screw

NOTE: When reinstalling the side panel, set the bottom edge on the rail, hook the front edge at the top and bottom, and install the two rear screws; then install the bottom screw from inside the rear of the unit.

4-19

Image 45

Contents SELF-CLEANING SLIDE-IN Electric Range Goals and Objectives ForwardTable of Contents Wiring Diagram & Strip Circuits General Safety FirstElectrostatic Discharge ESD Sensitive Electronics Kitchenaid Model & Serial Number Designations Model NumberSerial Number Model & Serial Number Location Located Behind Storage Drawer Model & Serial Number Label LocationKESC300H WH/BL/BT KESC307H WH/BT/BS KESH307H WH/BL/BS SpecificationsInterior Limited Warranty Kitchenaid Electric Range WarrantyPage General Electrical Supply RequirementsElectrical Connections Not used for Canadian Installations Wire Electrical Connection Power Supply Cord ConnectionLine Direct Wire Connection Ground link Screw Line Moving the Range AIR Flow Rear Panel Theory of OperationAIR Inlets Under Control Panel Cooling FAN AIR FlowBimetal Switches Inset #2Inset #1 Surface Element Limiter Door Lock Solenoid Door Unlocked Door Lock Solenoid & Door Latch SwitchAfter 30 Minutes of Clean HOW the SELF-CLEAN Cycle WorksComponent Locations Component AccessTo remove the control panel To remove an infinite switchTo remove a bimetal switch Removing the Electronic Oven Control AN Indicator Light To remove an indicator lightTo remove the electronic oven control On the next To remove an element and limiterTo remove the hot surface indicator assembly Removing the Cooktop Glass Lower the cooktop Lift Grate Off Cooktop Rear Trim Rear Trim Tension Brackets To remove the door latch assembly Removing the Door Latch Assembly Door SwitchTo remove the door switch Removing the Dual Broil Element Hidden Bake Element To remove the dual broil elementTo remove the hidden bake element Element Shield Screw Element Wires To remove the convection bake ele- ment Removing the Convection Bake Element & FAN MotorTo remove the convection fan motor Removing AN Oven Light Socket Assembly Removing the Meat Probe Jack Removing the Oven Temperature Sensor Removing a Side Panel Removing the Double Line Break DLB Relay Cooling FAN Motor To remove the double line break DLB relayTo remove the cooling fan motor Remove This Screw Loosen These Screws Housing Removing the Oven Door To reinstall the oven doorTo remove the decorative glass To remove the door handleTo remove a hinge To remove the inner and outer oven door glass Removing the Oven Door Gasket Page Bimetal Switch Component TestingSingle Element Infinite Switches Dual Element Infinite Switch Optional To test the left front LF dual element and limiter Surface Elements & LimitersTo test the RF, LR, & RR single ele- ments & limiters To test the door latch switch Door Switch N.ODual Broil Element Hidden Bake ElementConvection FAN Motor Convection Bake ElementCooling FAN Motor Oven Temperature SensorDouble Line Break DLB Relay Diagnosis Diagnosis & TroubleshootingFault Error F1E3 Fault Error Code ChartsProblem Possible Cause Solution Troubleshooting ChartsProblem Possible Cause Solution Problem Possible Cause Solution Oven Temperature Calibration Wiring Diagram #9753028, REV. B Wiring Diagram & Strip CircuitsPage Strip Circuits CleanBake Including PRE-HEAT Broil EconoConvection Broil Driving CircuitHalogen Oven Lights Optional Oven Light OptionalPage Product Specifications Warranty Information Sources