KitchenAid KESH307H, KESC300H, KESC307H manual Element Shield Screw Element Wires

Page 39

c)Disconnect the two wire connectors from the hidden bake element termi- nals.

d)Remove the element shield screw from the right end of the shield.

Element Shield Screw

Element Wires

e)Pull the hidden bake element and its shield to the right and unhook the left and right tabs.

Right End

Unhook Tab From Slot

Hidden Bake Element Shield

Unhook End From Slot

Left End

f)Remove the hidden bake element from the unit, and place it on a work surface.

Pull Out

Pull Out

g)Remove the two bracket screws, and remove the shield from the element.

Element Shield Screw

4-13

Image 39

Contents SELF-CLEANING SLIDE-IN Electric Range Goals and Objectives ForwardTable of Contents Wiring Diagram & Strip Circuits General Safety FirstElectrostatic Discharge ESD Sensitive Electronics Kitchenaid Model & Serial Number Designations Model NumberSerial Number Model & Serial Number Location Located Behind Storage Drawer Model & Serial Number Label LocationKESC300H WH/BL/BT KESC307H WH/BT/BS KESH307H WH/BL/BS SpecificationsInterior Limited Warranty Kitchenaid Electric Range WarrantyPage General Electrical Supply RequirementsElectrical Connections Not used for Canadian Installations Wire Electrical Connection Power Supply Cord ConnectionLine Direct Wire Connection Ground link Screw Line Moving the Range AIR Flow Rear Panel Theory of OperationAIR Inlets Under Control Panel Cooling FAN AIR FlowBimetal Switches Inset #2Inset #1 Surface Element Limiter Door Lock Solenoid Door Unlocked Door Lock Solenoid & Door Latch SwitchAfter 30 Minutes of Clean HOW the SELF-CLEAN Cycle WorksComponent Locations Component AccessTo remove the control panel To remove an infinite switchTo remove a bimetal switch Removing the Electronic Oven Control AN Indicator Light To remove an indicator lightTo remove the electronic oven control On the next To remove an element and limiterTo remove the hot surface indicator assembly Removing the Cooktop Glass Lower the cooktop Lift Grate Off Cooktop Rear Trim Rear Trim Tension Brackets To remove the door latch assembly Removing the Door Latch Assembly Door SwitchTo remove the door switch Removing the Dual Broil Element Hidden Bake Element To remove the dual broil elementTo remove the hidden bake element Element Shield Screw Element Wires To remove the convection bake ele- ment Removing the Convection Bake Element & FAN MotorTo remove the convection fan motor Removing AN Oven Light Socket Assembly Removing the Meat Probe Jack Removing the Oven Temperature Sensor Removing a Side Panel Removing the Double Line Break DLB Relay Cooling FAN Motor To remove the double line break DLB relayTo remove the cooling fan motor Remove This Screw Loosen These Screws Housing Removing the Oven Door To reinstall the oven doorTo remove the decorative glass To remove the door handleTo remove a hinge To remove the inner and outer oven door glass Removing the Oven Door Gasket Page Bimetal Switch Component TestingSingle Element Infinite Switches Dual Element Infinite Switch Optional To test the left front LF dual element and limiter Surface Elements & LimitersTo test the RF, LR, & RR single ele- ments & limiters To test the door latch switch Door Switch N.ODual Broil Element Hidden Bake ElementConvection FAN Motor Convection Bake ElementCooling FAN Motor Oven Temperature SensorDouble Line Break DLB Relay Diagnosis Diagnosis & TroubleshootingFault Error F1E3 Fault Error Code ChartsProblem Possible Cause Solution Troubleshooting ChartsProblem Possible Cause Solution Problem Possible Cause Solution Oven Temperature Calibration Wiring Diagram #9753028, REV. B Wiring Diagram & Strip CircuitsPage Broil Econo CleanStrip Circuits Bake Including PRE-HEATConvection Broil Driving CircuitHalogen Oven Lights Optional Oven Light OptionalPage Product Specifications Warranty Information Sources