KitchenAid KESC300H, KESH307H, KESC307H manual Door Switch N.O, To test the door latch switch

Page 58

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

DOOR SWITCH (N.O.)

DOOR LATCH ASSEMBLY (N.O.)

Refer to page 4-10 for the procedure for servic- ing the door switch.

1.Unplug range or disconnect power.

2.Set the ohmmeter to the R x 1 scale.

3.Touch the ohmmeter test leads to the door switch terminals. The meter should indi- cate an open circuit (infinite).

4.Press the actuator button and the meter should indicate continuity (0 Ω).

Door Latch Switch

Door Latch Solenoid

Refer to page 4-10 for the procedure for servic- ing the door latch assembly.

1.Unplug range or disconnect power.

2.Disconnect one of the wires from the door latch assembly component under test.

3.Set the ohmmeter to the R x 1K scale.

4.To test the solenoid, touch the ohmme- ter test leads to the terminals. The meter

should indicate between 3000 and 3800

Ω.

5.To test the door latch switch:

a)Touch the ohmmeter test leads to the COM and N.O. terminals. The meter should indicate an open circuit (infinite).

b)With the ohmmeter leads connected as stated in the previous step, press the

switch actuator. The meter should in- dicate continuity (0 Ω).

5-6

Image 58

Contents SELF-CLEANING SLIDE-IN Electric Range Forward Goals and ObjectivesTable of Contents Wiring Diagram & Strip Circuits Safety First GeneralElectrostatic Discharge ESD Sensitive Electronics Model Number Kitchenaid Model & Serial Number DesignationsSerial Number Model & Serial Number Label Location Model & Serial Number Location Located Behind Storage DrawerSpecifications KESC300H WH/BL/BT KESC307H WH/BT/BS KESH307H WH/BL/BSInterior Kitchenaid Electric Range Warranty Limited WarrantyPage Electrical Supply Requirements GeneralElectrical Connections Not used for Canadian Installations Power Supply Cord Connection Wire Electrical ConnectionLine Direct Wire Connection Ground link Screw Line Moving the Range Theory of Operation AIR Flow Rear PanelCooling FAN AIR Flow AIR Inlets Under Control PanelInset #2 Bimetal SwitchesInset #1 Surface Element Limiter Door Lock Solenoid & Door Latch Switch Door Lock Solenoid Door UnlockedHOW the SELF-CLEAN Cycle Works After 30 Minutes of CleanComponent Access Component LocationsTo remove an infinite switch To remove the control panelTo remove a bimetal switch To remove an indicator light Removing the Electronic Oven Control AN Indicator LightTo remove the electronic oven control To remove an element and limiter On the nextTo remove the hot surface indicator assembly Removing the Cooktop Glass Lower the cooktop Lift Grate Off Cooktop Rear Trim Rear Trim Tension Brackets Removing the Door Latch Assembly Door Switch To remove the door latch assemblyTo remove the door switch To remove the dual broil element Removing the Dual Broil Element Hidden Bake ElementTo remove the hidden bake element Element Shield Screw Element Wires Removing the Convection Bake Element & FAN Motor To remove the convection bake ele- mentTo remove the convection fan motor Removing AN Oven Light Socket Assembly Removing the Meat Probe Jack Removing the Oven Temperature Sensor Removing a Side Panel To remove the double line break DLB relay Removing the Double Line Break DLB Relay Cooling FAN MotorTo remove the cooling fan motor Remove This Screw Loosen These Screws Housing To reinstall the oven door Removing the Oven DoorTo remove the door handle To remove the decorative glassTo remove a hinge To remove the inner and outer oven door glass Removing the Oven Door Gasket Page Component Testing Bimetal SwitchSingle Element Infinite Switches Dual Element Infinite Switch Optional Surface Elements & Limiters To test the left front LF dual element and limiterTo test the RF, LR, & RR single ele- ments & limiters Door Switch N.O To test the door latch switchHidden Bake Element Dual Broil ElementConvection Bake Element Convection FAN MotorOven Temperature Sensor Cooling FAN MotorDouble Line Break DLB Relay Diagnosis & Troubleshooting DiagnosisFault Error Code Charts Fault Error F1E3Troubleshooting Charts Problem Possible Cause SolutionProblem Possible Cause Solution Problem Possible Cause Solution Oven Temperature Calibration Wiring Diagram & Strip Circuits Wiring Diagram #9753028, REV. BPage Bake Including PRE-HEAT CleanStrip Circuits Broil EconoDriving Circuit Convection BroilOven Light Optional Halogen Oven Lights OptionalPage Product Specifications Warranty Information Sources