KitchenAid KESH307H, KESC300H, KESC307H manual Removing the Door Latch Assembly Door Switch

Page 36

REMOVING THE DOOR LATCH ASSEMBLY

& THE DOOR SWITCH

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

1.Unplug range or disconnect power.

2.Pull the range away from the wall so that you can access the rear of the unit.

3.To remove the door latch assembly:

a)Remove the top and side screws from the rear panel and loosen the three bottom screws, then pull the tabs out of their slots, and remove the panel.

2 Screws

Rear Panel

Loosen 3 Screws

Door Latch Assembly

b)Disconnect the 3-wire connector from the door latch switch terminals.

c)Disconnect the wires from the door latch solenoid terminals.

d)Remove the two screws from the door latch assembly and remove it from the unit.

Door Latch Switch

3-Wire Connector

Screw

(1 of 2)

Door Latch Solenoid

Terminals

REASSEMBLY NOTE: When you reinstall the door latch assembly, make sure that the door latch switch actuator is over the latching rod, as shown.

Door Latch

Switch Actuator

Latching Rod

4-10

Image 36

Contents SELF-CLEANING SLIDE-IN Electric Range Forward Goals and ObjectivesTable of Contents Wiring Diagram & Strip Circuits Safety First GeneralElectrostatic Discharge ESD Sensitive Electronics Kitchenaid Model & Serial Number Designations Model NumberSerial Number Model & Serial Number Label Location Model & Serial Number Location Located Behind Storage DrawerSpecifications KESC300H WH/BL/BT KESC307H WH/BT/BS KESH307H WH/BL/BSInterior Kitchenaid Electric Range Warranty Limited WarrantyPage Electrical Supply Requirements GeneralElectrical Connections Not used for Canadian Installations Power Supply Cord Connection Wire Electrical ConnectionLine Direct Wire Connection Ground link Screw Line Moving the Range Theory of Operation AIR Flow Rear PanelCooling FAN AIR Flow AIR Inlets Under Control PanelBimetal Switches Inset #2Inset #1 Surface Element Limiter Door Lock Solenoid & Door Latch Switch Door Lock Solenoid Door UnlockedHOW the SELF-CLEAN Cycle Works After 30 Minutes of CleanComponent Access Component LocationsTo remove an infinite switch To remove the control panelTo remove a bimetal switch Removing the Electronic Oven Control AN Indicator Light To remove an indicator lightTo remove the electronic oven control To remove an element and limiter On the nextTo remove the hot surface indicator assembly Removing the Cooktop Glass Lower the cooktop Lift Grate Off Cooktop Rear Trim Rear Trim Tension Brackets Removing the Door Latch Assembly Door Switch To remove the door latch assemblyTo remove the door switch Removing the Dual Broil Element Hidden Bake Element To remove the dual broil elementTo remove the hidden bake element Element Shield Screw Element Wires Removing the Convection Bake Element & FAN Motor To remove the convection bake ele- mentTo remove the convection fan motor Removing AN Oven Light Socket Assembly Removing the Meat Probe Jack Removing the Oven Temperature Sensor Removing a Side Panel Removing the Double Line Break DLB Relay Cooling FAN Motor To remove the double line break DLB relayTo remove the cooling fan motor Remove This Screw Loosen These Screws Housing To reinstall the oven door Removing the Oven DoorTo remove the decorative glass To remove the door handleTo remove a hinge To remove the inner and outer oven door glass Removing the Oven Door Gasket Page Component Testing Bimetal SwitchSingle Element Infinite Switches Dual Element Infinite Switch Optional Surface Elements & Limiters To test the left front LF dual element and limiterTo test the RF, LR, & RR single ele- ments & limiters Door Switch N.O To test the door latch switchHidden Bake Element Dual Broil ElementConvection Bake Element Convection FAN MotorOven Temperature Sensor Cooling FAN MotorDouble Line Break DLB Relay Diagnosis & Troubleshooting DiagnosisFault Error Code Charts Fault Error F1E3Troubleshooting Charts Problem Possible Cause SolutionProblem Possible Cause Solution Problem Possible Cause Solution Oven Temperature Calibration Wiring Diagram & Strip Circuits Wiring Diagram #9753028, REV. BPage Clean Strip CircuitsBake Including PRE-HEAT Broil EconoDriving Circuit Convection BroilOven Light Optional Halogen Oven Lights OptionalPage Product Specifications Warranty Information Sources