Frymaster FMCF operation manual Canada

Page 2

NOTICE

This appliance is intended for professional use only and is to be operated by qualified

personnel only. A Frymaster/DEAN Factory Authorized Service Center (FASC) or other qualified professional should perform installation, maintenance, and repairs. Installation, maintenance, or repairs by unqualified personnel may void the manufacturer’s warranty. See Chapter 1 of this manual for definitions of qualified personnel.

NOTICE

This equipment must be installed in accordance with the appropriate national and local codes of

the country and/or region in which the appliance is installed. See NATIONAL CODE

REQUIREMENTS in Chapter 2 of this manual for specifics.

NOTICE TO U.S. CUSTOMERS

This equipment is to be installed in compliance with the basic plumbing code of the Building Officials and Code Administrators International, Inc. (BOCA) and the Food Service Sanitation Manual of the U.S. Food and Drug Administration.

NOTICE

Drawings and photos used in this manual are intended to illustrate operational, cleaning and technical procedures and may not conform to onsite management operational procedures.

NOTICE TO OWNERS OF UNITS EQUIPPED WITH COMPUTERS

U.S.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. While this device is a verified Class A device, it has been shown to meet the Class B limits.

CANADA

This digital apparatus does not exceed the Class A or B limits for radio noise emissions as set out by the ICES-003 standard of the Canadian Department of Communications.

Cet appareil numerique n’emet pas de bruits radioelectriques depassany les limites de classe A et B prescrites dans la norme NMB-003 edictee par le Ministre des Communcations du Canada.

DANGER

Improper installation, adjustment, maintenance or service, and unauthorized alterations or modifications can cause property damage, injury, or death. Read the installation, operating, and service instructions thoroughly before installing or servicing this equipment. Only qualified service personnel may convert this appliance to use a gas other than that for which it was originally configured.

DANGER

No structural material on the fryer should be altered or removed to accommodate placement of the fryer under a hood. Questions? Call the Frymaster/Dean Service Hotline at 1-800-551-8633.

ii

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Gas Fryers NON-CECanada Iii CF Series Gas Fryers Parts Ordering and Service Information Applicability and ValidityCF Series GAS Fryers Introduction Safety InformationEuropean Community CE Specific Information CE Standard For Incoming Gas PressuresEquipment Description Installation, Operating, and Service Personnel DefinitionsShipping Damage Claim Procedure Retain and Store this Manual in a Safe Place for Future USECF Series GAS Fryers Installation Instructions General Installation RequirementsPage FCC Compliance Australian RequirementsElectrical Grounding Requirements Pre-Connection Preparations Caster/Leg InstallationCF Series GAS Fryers Installation Instructions CE Standard For Incoming Gas Pressures Connection to Gas Line CE Approved Gas CategoriesCE Standard Gas Connection Pipe SizesConverting to Another Gas Type CE Standard Burner Manifold Gas PressuresNon-CE Gas Conversion Instructions CE Gas Conversion InstructionsCE Only Start-Up Procedure CF Series GAS Fryers Operating InstructionsLighting the Pilot on NON-CE Fryers Lighting the PilotPlacing the Fryer Into Operation Branded locations Boiling-Out the FrypotCF Series GAS Fryers Operating Instructions For units equipped with a Computer Magic III.5 Computer Shutting the Fryer Down Controller Operation and ProgrammingCF Series GAS Fryers Filtration Instructions Draining and Manual FilteringCF Series GAS Fryers Filtration Instructions Filter Magic II Filtration System Operation Filter Magic II Filtration System Operation Filter Magic II Filtration System Operation Drain valve in the open position CF Series GAS Fryers Filtration Instructions Drain handle in the closed position Inspect Fryer and Accessories for Damage Fryer Preventive Maintenance Checks and ServicesDaily Checks and Services Clean Fryer Cabinet Inside and OutQuarterly Checks and Services Check Recovery TimeClean Float Switch and Shaft Drain and Clean FrypotCF Series GAS Fryers Preventative Maintenance Clean Detachable Parts and AccessoriesCheck Computer Magic III Set Point Accuracy Clean Gas Valve Vent TubeCheck Thermostat Controller Thermostat Calibration Check Burner Manifold Pressure CF Series GAS Fryers Preventative Maintenance Built-In Filtration System CF Series GAS Fryers Operator Troubleshooting IntroductionCF Series GAS Fryers Operator Troubleshooting Problem Probable Causes Corrective ActionIndicator is on but Heating modeIndicator does not Into programmingProblem Troubleshooting Fryers with Thermostat ControlsTroubleshooting the Built-In Filtration System Transfer takes place Filtering.Pump starts, but no Or the transfer isSlow. Power Shower is notOr the transfer is very Spraying properlyTroubleshooting Abnormal Burner Operation Replacing the Controller or Controller Wiring Harness This page Intentionally Left Blank Service Hotline

FMCF specifications

The Frymaster FMCF is an innovative frying solution designed to meet the demands of modern commercial kitchens. Known for its advanced technology and efficiency, the FMCF model is a testament to Frymaster's commitment to quality and performance in the foodservice industry. It caters to various frying needs, making it an ideal choice for restaurants, fast-food chains, and catering businesses.

One of the main features of the Frymaster FMCF is its high-capacity fry tank, which allows for large volumes of food to be cooked simultaneously. This high-capacity model ensures that busy kitchens can keep up with customer demand without compromising on quality. The unit is designed to accommodate a variety of popular fried items, including chicken, fries, and seafood, making it versatile for diverse menus.

The FMCF incorporates advanced oil filtration technology, which significantly extends the life of the frying oil. This feature not only reduces operational costs but also enhances food quality by maintaining a consistent frying temperature and preventing flavor contamination. The built-in filtration system operates automatically, ensuring that the oil is filtered regularly and efficiently, thus allowing chefs to focus on food preparation rather than maintenance.

Another noteworthy characteristic of the Frymaster FMCF is its user-friendly digital control system. The intuitive interface allows operators to easily monitor and adjust frying times, temperatures, and oil usage. This precision is crucial in achieving perfect frying results consistently. Additionally, the digital controls include programmable cooking profiles, enabling staff to replicate specific cooking processes, which is vital for maintaining product consistency across different shifts and locations.

The Frymaster FMCF is engineered with energy efficiency in mind. Its design minimizes heat loss, resulting in reduced energy consumption. This not only helps save on utility bills but also contributes to a more sustainable operation. This energy efficiency is complemented by safety features, including automatic shut-off valves and temperature controls, which enhance the overall safety of the frying process.

In summary, the Frymaster FMCF is a high-performance fryer that combines capacity, advanced oil filtration, user-friendly controls, and energy efficiency. These features make it a preferred choice for establishments that require reliability, consistency, and quality in their frying operations. With its robust design and innovative technology, the FMCF stands out as an essential tool for modern kitchens looking to deliver the best fried food experiences to their customers.
Top Page Image Contents