Frymaster FMCF operation manual Lighting the Pilot on NON-CE Fryers

Page 21

CF SERIES GAS FRYERS

CHAPTER 3: OPERATING INSTRUCTIONS

ACCESSING THE PILOT

The pilot is mounted on the left side of the burner manifold and is accessed through an opening in the front frypot insulation. Swing the round cover open and insert a long match or taper through the hole (see photo) when lighting the pilot.

Insert match or taper through this hole to light pilot.

LIGHTING THE PILOT ON NON-CE FRYERS

1.Ensure power to the unit is OFF, and then turn the gas valve knob to the OFF position. Wait at least 5 minutes, and then rotate the gas valve knob to the PILOT position (see Figure 1).

Lighting the Pilot

 

PILOT

ON

OFF

 

Figure 1

 

PILOT

ON

OFF

 

Figure 2

2.Push the knob in and light the pilot. (If the fryer is equipped with a piezo ignitor, repeatedly press the piezo ignitor button while depressing the gas valve knob until the pilot lights.) Continue to hold the knob in for about 60 seconds after the flame appears on the pilot. Release the knob. The pilot should remain lit.

CAUTION

If the pilot fails to remain lit, turn the gas valve knob to the OFF position and wait at

least five minutes before attempting to re-light.

3.With the pilot lit, push down and slowly turn the knob to the ON position (Figure 2).

3-2

Page 20 Page 22
Image 21
Page 20 Page 22
Contents NON-CE Gas FryersCanada Iii CF Series Gas Fryers Applicability and Validity Parts Ordering and Service InformationEuropean Community CE Specific Information Safety InformationCF Series GAS Fryers Introduction CE Standard For Incoming Gas PressuresEquipment Description Definitions Installation, Operating, and Service PersonnelRetain and Store this Manual in a Safe Place for Future USE Shipping Damage Claim ProcedureGeneral Installation Requirements CF Series GAS Fryers Installation InstructionsPage Australian Requirements Electrical Grounding RequirementsFCC Compliance Caster/Leg Installation CF Series GAS Fryers Installation InstructionsPre-Connection Preparations CE Standard For Incoming Gas Pressures CE Approved Gas Categories Connection to Gas LineGas Connection Pipe Sizes CE StandardCE Standard Burner Manifold Gas Pressures Converting to Another Gas TypeCE Gas Conversion Instructions Non-CE Gas Conversion InstructionsCE Only CF Series GAS Fryers Operating Instructions Start-Up ProcedureLighting the Pilot Lighting the Pilot on NON-CE FryersPlacing the Fryer Into Operation Boiling-Out the Frypot CF Series GAS Fryers Operating InstructionsBranded locations For units equipped with a Computer Magic III.5 Computer Controller Operation and Programming Shutting the Fryer DownDraining and Manual Filtering CF Series GAS Fryers Filtration InstructionsCF Series GAS Fryers Filtration Instructions Filter Magic II Filtration System Operation Filter Magic II Filtration System Operation Filter Magic II Filtration System Operation Drain valve in the open position CF Series GAS Fryers Filtration Instructions Drain handle in the closed position Daily Checks and Services Fryer Preventive Maintenance Checks and ServicesInspect Fryer and Accessories for Damage Clean Fryer Cabinet Inside and OutClean Float Switch and Shaft Check Recovery TimeQuarterly Checks and Services Drain and Clean FrypotClean Detachable Parts and Accessories CF Series GAS Fryers Preventative MaintenanceClean Gas Valve Vent Tube Check Thermostat Controller Thermostat CalibrationCheck Computer Magic III Set Point Accuracy Check Burner Manifold Pressure CF Series GAS Fryers Preventative Maintenance Built-In Filtration System Introduction CF Series GAS Fryers Operator TroubleshootingProblem Probable Causes Corrective Action CF Series GAS Fryers Operator TroubleshootingIndicator does not Heating modeIndicator is on but Into programmingTroubleshooting Fryers with Thermostat Controls Troubleshooting the Built-In Filtration SystemProblem Pump starts, but no Filtering.Transfer takes place Or the transfer isOr the transfer is very Power Shower is notSlow. Spraying properlyTroubleshooting Abnormal Burner Operation Replacing the Controller or Controller Wiring Harness This page Intentionally Left Blank Service Hotline

FMCF specifications

The Frymaster FMCF is an innovative frying solution designed to meet the demands of modern commercial kitchens. Known for its advanced technology and efficiency, the FMCF model is a testament to Frymaster's commitment to quality and performance in the foodservice industry. It caters to various frying needs, making it an ideal choice for restaurants, fast-food chains, and catering businesses.

One of the main features of the Frymaster FMCF is its high-capacity fry tank, which allows for large volumes of food to be cooked simultaneously. This high-capacity model ensures that busy kitchens can keep up with customer demand without compromising on quality. The unit is designed to accommodate a variety of popular fried items, including chicken, fries, and seafood, making it versatile for diverse menus.

The FMCF incorporates advanced oil filtration technology, which significantly extends the life of the frying oil. This feature not only reduces operational costs but also enhances food quality by maintaining a consistent frying temperature and preventing flavor contamination. The built-in filtration system operates automatically, ensuring that the oil is filtered regularly and efficiently, thus allowing chefs to focus on food preparation rather than maintenance.

Another noteworthy characteristic of the Frymaster FMCF is its user-friendly digital control system. The intuitive interface allows operators to easily monitor and adjust frying times, temperatures, and oil usage. This precision is crucial in achieving perfect frying results consistently. Additionally, the digital controls include programmable cooking profiles, enabling staff to replicate specific cooking processes, which is vital for maintaining product consistency across different shifts and locations.

The Frymaster FMCF is engineered with energy efficiency in mind. Its design minimizes heat loss, resulting in reduced energy consumption. This not only helps save on utility bills but also contributes to a more sustainable operation. This energy efficiency is complemented by safety features, including automatic shut-off valves and temperature controls, which enhance the overall safety of the frying process.

In summary, the Frymaster FMCF is a high-performance fryer that combines capacity, advanced oil filtration, user-friendly controls, and energy efficiency. These features make it a preferred choice for establishments that require reliability, consistency, and quality in their frying operations. With its robust design and innovative technology, the FMCF stands out as an essential tool for modern kitchens looking to deliver the best fried food experiences to their customers.
Top Page Image Contents