Frymaster FMCF operation manual CF Series GAS Fryers Filtration Instructions

Page 27

CF SERIES GAS FRYERS

CHAPTER 4: FILTRATION INSTRUCTIONS

If you are using a Frymaster filter cone holder, be sure that the cone holder rests securely on the metal container.

3.Open the drain valve slowly to avoid splattering. If the drain valve becomes clogged with food particles, use the Fryer’s Friend (poker-like tool) to clear the blockage.

DANGER

DO NOT insert anything into the drain from the front to unclog the valve. Hot oil will

rush out, creating an extreme hazard.

WARNING

DO NOT hammer on the drain valve with the Fryer’s Friend. This will damage the drain valve ball and prevent the valve from sealing securely, resulting in a leaky valve.

4.After draining the oil, clean all food particles and residual oil from the frypot. If the fryer is equipped with a float switch, clean it at this time. The float switch prevents frypot damage in the event the power switch is not OFF while draining used oil. The float switch must be cleaned on a regular basis to ensure proper operation. Use caution as frypot residue can cause severe burns if it contacts bare skin.

5.Close the drain valve securely and fill the frypot with clean, filtered or fresh cooking oil or solid shortening to the bottom OIL-LEVELline.

DANGER

When using solid shortening, pack it down into the cool-zone and the bottom of the frypot. DO NOT operate the fryer with a block of shortening sitting in the upper portion of the frypot. Irreparable damage to the frypot and a potential flash fire will result.

4-2

Page 26 Page 28
Image 27
Page 26 Page 28
Contents NON-CE Gas FryersCanada Iii CF Series Gas Fryers Applicability and Validity Parts Ordering and Service InformationCE Standard For Incoming Gas Pressures Safety InformationEuropean Community CE Specific Information CF Series GAS Fryers IntroductionEquipment Description Definitions Installation, Operating, and Service PersonnelRetain and Store this Manual in a Safe Place for Future USE Shipping Damage Claim ProcedureGeneral Installation Requirements CF Series GAS Fryers Installation InstructionsPage Australian Requirements Electrical Grounding RequirementsFCC Compliance Caster/Leg Installation CF Series GAS Fryers Installation InstructionsPre-Connection Preparations CE Standard For Incoming Gas Pressures CE Approved Gas Categories Connection to Gas LineGas Connection Pipe Sizes CE StandardCE Standard Burner Manifold Gas Pressures Converting to Another Gas TypeCE Gas Conversion Instructions Non-CE Gas Conversion InstructionsCE Only CF Series GAS Fryers Operating Instructions Start-Up ProcedureLighting the Pilot Lighting the Pilot on NON-CE FryersPlacing the Fryer Into Operation Boiling-Out the Frypot CF Series GAS Fryers Operating InstructionsBranded locations For units equipped with a Computer Magic III.5 Computer Controller Operation and Programming Shutting the Fryer DownDraining and Manual Filtering CF Series GAS Fryers Filtration InstructionsCF Series GAS Fryers Filtration Instructions Filter Magic II Filtration System Operation Filter Magic II Filtration System Operation Filter Magic II Filtration System Operation Drain valve in the open position CF Series GAS Fryers Filtration Instructions Drain handle in the closed position Clean Fryer Cabinet Inside and Out Fryer Preventive Maintenance Checks and ServicesDaily Checks and Services Inspect Fryer and Accessories for DamageDrain and Clean Frypot Check Recovery TimeClean Float Switch and Shaft Quarterly Checks and ServicesClean Detachable Parts and Accessories CF Series GAS Fryers Preventative MaintenanceClean Gas Valve Vent Tube Check Thermostat Controller Thermostat CalibrationCheck Computer Magic III Set Point Accuracy Check Burner Manifold Pressure CF Series GAS Fryers Preventative Maintenance Built-In Filtration System Introduction CF Series GAS Fryers Operator TroubleshootingProblem Probable Causes Corrective Action CF Series GAS Fryers Operator TroubleshootingInto programming Heating modeIndicator does not Indicator is on butTroubleshooting Fryers with Thermostat Controls Troubleshooting the Built-In Filtration SystemProblem Or the transfer is Filtering.Pump starts, but no Transfer takes placeSpraying properly Power Shower is notOr the transfer is very Slow.Troubleshooting Abnormal Burner Operation Replacing the Controller or Controller Wiring Harness This page Intentionally Left Blank Service Hotline

FMCF specifications

The Frymaster FMCF is an innovative frying solution designed to meet the demands of modern commercial kitchens. Known for its advanced technology and efficiency, the FMCF model is a testament to Frymaster's commitment to quality and performance in the foodservice industry. It caters to various frying needs, making it an ideal choice for restaurants, fast-food chains, and catering businesses.

One of the main features of the Frymaster FMCF is its high-capacity fry tank, which allows for large volumes of food to be cooked simultaneously. This high-capacity model ensures that busy kitchens can keep up with customer demand without compromising on quality. The unit is designed to accommodate a variety of popular fried items, including chicken, fries, and seafood, making it versatile for diverse menus.

The FMCF incorporates advanced oil filtration technology, which significantly extends the life of the frying oil. This feature not only reduces operational costs but also enhances food quality by maintaining a consistent frying temperature and preventing flavor contamination. The built-in filtration system operates automatically, ensuring that the oil is filtered regularly and efficiently, thus allowing chefs to focus on food preparation rather than maintenance.

Another noteworthy characteristic of the Frymaster FMCF is its user-friendly digital control system. The intuitive interface allows operators to easily monitor and adjust frying times, temperatures, and oil usage. This precision is crucial in achieving perfect frying results consistently. Additionally, the digital controls include programmable cooking profiles, enabling staff to replicate specific cooking processes, which is vital for maintaining product consistency across different shifts and locations.

The Frymaster FMCF is engineered with energy efficiency in mind. Its design minimizes heat loss, resulting in reduced energy consumption. This not only helps save on utility bills but also contributes to a more sustainable operation. This energy efficiency is complemented by safety features, including automatic shut-off valves and temperature controls, which enhance the overall safety of the frying process.

In summary, the Frymaster FMCF is a high-performance fryer that combines capacity, advanced oil filtration, user-friendly controls, and energy efficiency. These features make it a preferred choice for establishments that require reliability, consistency, and quality in their frying operations. With its robust design and innovative technology, the FMCF stands out as an essential tool for modern kitchens looking to deliver the best fried food experiences to their customers.
Top Page Image Contents