Frymaster FMCF operation manual Check Burner Manifold Pressure

Page 38

CF SERIES GAS FRYERS

CHAPTER 5: PREVENTATIVE MAINTENANCE

SEMI-ANNUAL CHECKS AND SERVICES

Check Burner Manifold Pressure

DANGER

This task should be performed by qualified service personnel only. Contact FASC to

arrange this service.

5.2Filter Magic II Filtration System Preventive Maintenance Checks and Services

The Filter Magic II Filtration System requires daily cleaning of the inner and outer filter pans with a solution of hot water and detergent. Turn the filter pan upside down and slightly elevate the end to allow all water to drain from the suction tube.

DANGER

The crumb tray in fryers equipped with a filter system must be emptied into a fireproof container at the end of frying operations each day. Some food particles can spontaneously combust if left soaking in certain shortening material.

If you notice that the system is pumping slowly or not at all, verify that the filter pan screen is on the bottom of the filter pan, with the paper on top of the screen. If the filter screen and paper are correctly installed, change the filter paper and verify that the O-rings on the connection fitting (located inside the cabinet at the back) are present and in good condition. NOTE: With fresh paper and properly installed O-rings, the system should refill the fryer in 2 to 3 minutes.

Immediately after each use, drain the Power Shower completely. If you suspect blockage, unscrew the clean-out plugs at each corner of the frame. Place the frame in a pan of hot water for several minutes to melt any accumulation of solidified oil. Use a long, narrow bottlebrush with hot water and detergent to clean inside the tubes. If necessary, insert a straightened paper clip or similar instrument into the holes in the frame to remove any blockages. Rinse, dry thoroughly, and reinstall the plugs before using.

DANGER

Failure to reinstall the Power Shower cleanout plugs will cause hot oil to spray out of

the frypot during the filtering process, creating a burn hazard to personnel.

5-5

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Gas Fryers NON-CECanada Iii CF Series Gas Fryers Parts Ordering and Service Information Applicability and ValidityCF Series GAS Fryers Introduction Safety InformationEuropean Community CE Specific Information CE Standard For Incoming Gas PressuresEquipment Description Installation, Operating, and Service Personnel DefinitionsShipping Damage Claim Procedure Retain and Store this Manual in a Safe Place for Future USECF Series GAS Fryers Installation Instructions General Installation RequirementsPage FCC Compliance Australian RequirementsElectrical Grounding Requirements Pre-Connection Preparations Caster/Leg InstallationCF Series GAS Fryers Installation Instructions CE Standard For Incoming Gas Pressures Connection to Gas Line CE Approved Gas CategoriesCE Standard Gas Connection Pipe SizesConverting to Another Gas Type CE Standard Burner Manifold Gas PressuresNon-CE Gas Conversion Instructions CE Gas Conversion InstructionsCE Only Start-Up Procedure CF Series GAS Fryers Operating InstructionsLighting the Pilot on NON-CE Fryers Lighting the PilotPlacing the Fryer Into Operation Branded locations Boiling-Out the FrypotCF Series GAS Fryers Operating Instructions For units equipped with a Computer Magic III.5 Computer Shutting the Fryer Down Controller Operation and ProgrammingCF Series GAS Fryers Filtration Instructions Draining and Manual FilteringCF Series GAS Fryers Filtration Instructions Filter Magic II Filtration System Operation Filter Magic II Filtration System Operation Filter Magic II Filtration System Operation Drain valve in the open position CF Series GAS Fryers Filtration Instructions Drain handle in the closed position Inspect Fryer and Accessories for Damage Fryer Preventive Maintenance Checks and ServicesDaily Checks and Services Clean Fryer Cabinet Inside and OutQuarterly Checks and Services Check Recovery TimeClean Float Switch and Shaft Drain and Clean FrypotCF Series GAS Fryers Preventative Maintenance Clean Detachable Parts and AccessoriesCheck Computer Magic III Set Point Accuracy Clean Gas Valve Vent TubeCheck Thermostat Controller Thermostat Calibration Check Burner Manifold Pressure CF Series GAS Fryers Preventative Maintenance Built-In Filtration System CF Series GAS Fryers Operator Troubleshooting IntroductionCF Series GAS Fryers Operator Troubleshooting Problem Probable Causes Corrective ActionIndicator is on but Heating modeIndicator does not Into programmingProblem Troubleshooting Fryers with Thermostat ControlsTroubleshooting the Built-In Filtration System Transfer takes place Filtering.Pump starts, but no Or the transfer isSlow. Power Shower is notOr the transfer is very Spraying properlyTroubleshooting Abnormal Burner Operation Replacing the Controller or Controller Wiring Harness This page Intentionally Left Blank Service Hotline

FMCF specifications

The Frymaster FMCF is an innovative frying solution designed to meet the demands of modern commercial kitchens. Known for its advanced technology and efficiency, the FMCF model is a testament to Frymaster's commitment to quality and performance in the foodservice industry. It caters to various frying needs, making it an ideal choice for restaurants, fast-food chains, and catering businesses.

One of the main features of the Frymaster FMCF is its high-capacity fry tank, which allows for large volumes of food to be cooked simultaneously. This high-capacity model ensures that busy kitchens can keep up with customer demand without compromising on quality. The unit is designed to accommodate a variety of popular fried items, including chicken, fries, and seafood, making it versatile for diverse menus.

The FMCF incorporates advanced oil filtration technology, which significantly extends the life of the frying oil. This feature not only reduces operational costs but also enhances food quality by maintaining a consistent frying temperature and preventing flavor contamination. The built-in filtration system operates automatically, ensuring that the oil is filtered regularly and efficiently, thus allowing chefs to focus on food preparation rather than maintenance.

Another noteworthy characteristic of the Frymaster FMCF is its user-friendly digital control system. The intuitive interface allows operators to easily monitor and adjust frying times, temperatures, and oil usage. This precision is crucial in achieving perfect frying results consistently. Additionally, the digital controls include programmable cooking profiles, enabling staff to replicate specific cooking processes, which is vital for maintaining product consistency across different shifts and locations.

The Frymaster FMCF is engineered with energy efficiency in mind. Its design minimizes heat loss, resulting in reduced energy consumption. This not only helps save on utility bills but also contributes to a more sustainable operation. This energy efficiency is complemented by safety features, including automatic shut-off valves and temperature controls, which enhance the overall safety of the frying process.

In summary, the Frymaster FMCF is a high-performance fryer that combines capacity, advanced oil filtration, user-friendly controls, and energy efficiency. These features make it a preferred choice for establishments that require reliability, consistency, and quality in their frying operations. With its robust design and innovative technology, the FMCF stands out as an essential tool for modern kitchens looking to deliver the best fried food experiences to their customers.
Top Page Image Contents