Frymaster H55 operation manual Non-CE Standard For Incoming Gas Pressures

Page 14

Non-CE Standard

for Incoming Gas Pressures

Gas

Minimum

Maximum

 

6" W.C.

14" W.C.

Natural

1.49 kPa

3.48 kPa

 

14.93 mbar

34.84 mbar

 

11" W.C.

14" W.C.

LP

2.74 kPa

3.48 kPa

 

27.37 mbar

34.84 mbar

 

 

 

 

 

 

7.For fryers equipped with a FootPrint Pro system or basket lifts, plug the electrical cord(s) into a power receptacle behind the fryer.

2.4Connection to Gas Line

DANGER

Before connecting new pipe to this appliance, the pipe must be blown out thor- oughly to remove all foreign material. Foreign material in the burner and gas con- trols will cause improper and dangerous operation.

DANGER

When pressure-testing incoming gas supply lines, disconnect the fryer from the gas line if the test pressure will be ½ PSIG (3.45 kPa, 13.84 inches W.C.) or greater to avoid damage to the fryer’s gas tubes and gas valve(s).

DANGER

All connections must be sealed with a joint compound suitable for the gas being used and all connections must be tested with a solution of soapy water before light- ing any pilots.

Never use matches, candles, or any other ignition source to check for leaks. If gas odors are detected, shut off the gas supply to the appliance at the main shut-off valve and immediately contact the local gas company or an authorized service agency for service.

DANGER

“Dry-firing” your unit will cause damage to the frypot and can cause a fire. Always ensure that melted shortening, cooking oil, or water is in the frypot before firing the unit.

The size of the gas line used for installation is very important. If the line is too small, the gas pressure at the burner manifold will be low. This may cause slow recovery and delayed ignition. The incoming gas supply line should be a minimum of 1½” (38 mm) in diameter. Refer to the chart on the following page for the minimum sizes of connection piping.

2-5

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Hour Service Hotline Frymaster domestic warranty Canada Iii PRO H55 Series GAS Fryer Table of Contents Applicability and Validity Parts Ordering and Service InformationPRO H55 Series GAS Fryer General Information Safety Information European Community CE Specific InformationDefinitions Installation, Operating, and Service PersonnelEquipment Description Shipping Damage Claim Procedure What to do if your equipment arrives damagedPRO H55 Series GAS Fryer Installation Instructions General Installation RequirementsNational Code Requirements Caster/Leg Installation Mbar = 10,2 mm H2O Non-CE Standard For Incoming Gas Pressures CE Standard Gas Connection Pipe SizesPressure mbar Non-CE Gas Conversion Kits CE Gas Conversion Kits for Units with Gas ValveCE GAS Conversion Instructions PRO H55 Series GAS Fryer Operating Instructions Controller Operation and ProgrammingLighting the Fryer For CE FryersBoiling Out the Frypot Shutting the Fryer DownPRO H55 Series GAS Fryers Filtration Instructions Page Preparation for Use with Filter Paper or Filter Pad Preparation for Use with the Magnasol Filter Assembly Use filter powder with the padPage Snap the optional Power Shower into position Filter Pump Reset Switch Cleaning ReassemblyDraining and Disposing of Waste Oil Using the Optional Rear-Discharge Oil Disposal Daily Checks and Service PRO H55 Series GAS Fryers Preventive MaintenanceFryer Preventive Maintenance Checks and Service Weekly Checks and ServiceClean Filter Pan, Detachable Parts and Accessories Check Computer Magic III.5 Set Point Accuracy Monthly Checks and ServiceAuthorized Service Center for assistance Quarterly Checks and Service Clean Combustion Air Blower AssemblyLeft Viewing Port is Behind Motor Right Check Burner Manifold Pressure SEMI-ANNUAL Checks and ServiceClean Gas Valve Vent Tube Fryer Built-In Filtration System PRO H55 Series GAS Fryers Operator Troubleshooting IntroductionProblem Probable Causes Corrective Action When cooking Fryer is operating Heating indicatorRecovery is slow Sound when burnersTroubleshooting Fryers with Solid State Analog Controller Will not ignite Heating mode light Fryer is slow coming Out of melt cycle Heating mode lightHeating mode light Is on and blower is Normally. BlowerPump stops during Troubleshooting the Built-in Filtration SystemPump won’t start FilteringTransfer takes place Power Shower is notPump starts, but no Or the transfer isMovement is jerky Troubleshooting the Basket LiftBasket lift And/or noisyService Hotline
Related manuals
Manual 48 pages 23.63 Kb Manual 70 pages 22.31 Kb

H55 specifications

The Frymaster H55 is a state-of-the-art commercial fryer that has gained acclaim in the foodservice industry for its advanced technology, efficiency, and exceptional cooking performance. Designed to meet the demanding needs of high-volume kitchens, the H55 stands out for its innovative features and user-friendly design.

One of the standout elements of the Frymaster H55 is its advanced filtration system, which ensures that oil remains clean for longer periods. This not only enhances the quality of the fried food but also extends the life of the frying oil, resulting in cost savings for operators. The automatic filtration system operates seamlessly, reducing the need for manual intervention and ensuring that frying can continue uninterrupted.

Another significant feature of the H55 is its Energy Star certification, which highlights its commitment to energy efficiency. This fryer employs a unique heat transfer design that maximizes energy use while minimizing waste. By utilizing less energy to achieve the same cooking results, the Frymaster H55 helps reduce operating costs and environmental impact.

The H55 also incorporates digital technology, making it easier for chefs to monitor cooking times and temperatures precisely. With adjustable temperature controls, users can achieve consistent frying results regardless of the type of food being prepared. Additionally, the intuitive touchscreen interface allows for easy navigation, even for kitchen staff with limited experience.

The design of the Frymaster H55 allows for versatility in cooking a wide array of menu items, from crispy fried chicken to delicate fish fillets. Its ample cooking capacity ensures that high-demand items can be prepared efficiently without sacrificing quality. Moreover, the H55’s robust construction and high-quality materials contribute to its durability, ensuring it can withstand the rigors of a busy kitchen environment.

Cleanliness and safety are also key priorities for the Frymaster H55. The fryer is equipped with safety features, including over-temperature protection and a drain valve that allows for safe and efficient oil disposal. Its design facilitates quick and thorough cleaning, ensuring that health and safety standards are consistently met.

In summary, the Frymaster H55 is a cutting-edge commercial fryer that embodies efficiency, safety, and innovation. With its advanced filtration system, energy-efficient design, digital controls, and versatility, it is an essential piece of equipment for any high-volume foodservice operation, delivering exceptional frying performance while reducing operational costs.
Top Page Image Contents