Frymaster H55 operation manual Built-In Filtration System

Page 39

•Verify that the temperature and high-limit probes are properly connected, tightened and functioning properly, and that probe guards are present and properly installed.

•Verify that component box components (i.e. computer/controller, transformers, relays, interface boards, etc.) are in good condition and free from oil and other debris. Inspect the component box wiring and verify that connections are tight and that wiring is in good condition.

•Verify that all safety features (i.e. drain safety switches, reset switches, etc.) are present and functioning properly.

•Verify that the frypot is in good condition and free of leaks and that the frypot insulation is in serviceable condition.

•Verify that wiring harnesses and connections are tight and in good condition.

Built-In Filtration System

•Inspect all oil-return and drain lines for leaks and verify that all connections are tight.

•Inspect the filter pan for leaks and cleanliness. If there is a large accumulation of crumbs in the crumb basket, advise the owner/operator that the crumb basket should be emptied into a fireproof container and cleaned daily.

•Verify that all O-rings and seals (including those on the Power Shower if applicable and on the quick-disconnect fitting) are present and in good condition. Replace O-rings and seals if worn or damaged.

•Check filtration system integrity as follows:

−Verify that filter pan cover is present and properly installed.

−With the filter pan empty, place each oil return handle, one at a time, in the ON position. Verify that the pump activates and that bubbles appear in the cooking oil/shortening (or that gurgling is heard from the Power Shower port if applicable) of the associated frypot.

−Close all oil return valves (i.e., place all oil return handles in the OFF position). Verify proper functioning of each oil return valve by activating the filter pump using the lever on one of the oil return microswitches. No air bubbles should be visible in any frypot (or no gurgling should be heard from the Power Shower ports if applicable).

−Verify that the filter pan is properly prepared for filtering, then drain a frypot of oil heated to 350°F (177°C) into the filter pan and close the frypot drain valve. Place the oil return handle in the ON position. Allow all cooking oil to return to the frypot (indicated by bubbles in the cooking oil or on units with Power Showers, cessation of oil flow from the Power Shower). Return the oil return handle to the OFF position. The frypot should have refilled in no more than 2 minutes and 30 seconds.

5-8

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Hour Service Hotline Frymaster domestic warranty Canada Iii PRO H55 Series GAS Fryer Table of Contents Parts Ordering and Service Information PRO H55 Series GAS Fryer General InformationApplicability and Validity European Community CE Specific Information Safety InformationInstallation, Operating, and Service Personnel Equipment DescriptionDefinitions What to do if your equipment arrives damaged Shipping Damage Claim ProcedureGeneral Installation Requirements PRO H55 Series GAS Fryer Installation InstructionsNational Code Requirements Caster/Leg Installation Mbar = 10,2 mm H2O Non-CE Standard For Incoming Gas Pressures Gas Connection Pipe Sizes CE StandardPressure mbar CE Gas Conversion Kits for Units with Gas Valve Non-CE Gas Conversion KitsCE GAS Conversion Instructions Controller Operation and Programming PRO H55 Series GAS Fryer Operating InstructionsFor CE Fryers Lighting the FryerShutting the Fryer Down Boiling Out the FrypotPRO H55 Series GAS Fryers Filtration Instructions Page Preparation for Use with Filter Paper or Filter Pad Use filter powder with the pad Preparation for Use with the Magnasol Filter AssemblyPage Snap the optional Power Shower into position Filter Pump Reset Switch Reassembly CleaningDraining and Disposing of Waste Oil Using the Optional Rear-Discharge Oil Disposal Weekly Checks and Service PRO H55 Series GAS Fryers Preventive MaintenanceFryer Preventive Maintenance Checks and Service Daily Checks and ServiceClean Filter Pan, Detachable Parts and Accessories Monthly Checks and Service Authorized Service Center for assistanceCheck Computer Magic III.5 Set Point Accuracy Clean Combustion Air Blower Assembly Quarterly Checks and ServiceLeft Viewing Port is Behind Motor Right SEMI-ANNUAL Checks and Service Clean Gas Valve Vent TubeCheck Burner Manifold Pressure Fryer Built-In Filtration System Introduction PRO H55 Series GAS Fryers Operator TroubleshootingProblem Probable Causes Corrective Action Sound when burners Heating indicatorRecovery is slow When cooking Fryer is operatingTroubleshooting Fryers with Solid State Analog Controller Normally. Blower Fryer is slow coming Out of melt cycle Heating mode lightHeating mode light Is on and blower is Will not ignite Heating mode lightFiltering Troubleshooting the Built-in Filtration SystemPump won’t start Pump stops duringOr the transfer is Power Shower is notPump starts, but no Transfer takes placeAnd/or noisy Troubleshooting the Basket LiftBasket lift Movement is jerkyService Hotline
Related manuals
Manual 48 pages 23.63 Kb Manual 70 pages 22.31 Kb

H55 specifications

The Frymaster H55 is a state-of-the-art commercial fryer that has gained acclaim in the foodservice industry for its advanced technology, efficiency, and exceptional cooking performance. Designed to meet the demanding needs of high-volume kitchens, the H55 stands out for its innovative features and user-friendly design.

One of the standout elements of the Frymaster H55 is its advanced filtration system, which ensures that oil remains clean for longer periods. This not only enhances the quality of the fried food but also extends the life of the frying oil, resulting in cost savings for operators. The automatic filtration system operates seamlessly, reducing the need for manual intervention and ensuring that frying can continue uninterrupted.

Another significant feature of the H55 is its Energy Star certification, which highlights its commitment to energy efficiency. This fryer employs a unique heat transfer design that maximizes energy use while minimizing waste. By utilizing less energy to achieve the same cooking results, the Frymaster H55 helps reduce operating costs and environmental impact.

The H55 also incorporates digital technology, making it easier for chefs to monitor cooking times and temperatures precisely. With adjustable temperature controls, users can achieve consistent frying results regardless of the type of food being prepared. Additionally, the intuitive touchscreen interface allows for easy navigation, even for kitchen staff with limited experience.

The design of the Frymaster H55 allows for versatility in cooking a wide array of menu items, from crispy fried chicken to delicate fish fillets. Its ample cooking capacity ensures that high-demand items can be prepared efficiently without sacrificing quality. Moreover, the H55’s robust construction and high-quality materials contribute to its durability, ensuring it can withstand the rigors of a busy kitchen environment.

Cleanliness and safety are also key priorities for the Frymaster H55. The fryer is equipped with safety features, including over-temperature protection and a drain valve that allows for safe and efficient oil disposal. Its design facilitates quick and thorough cleaning, ensuring that health and safety standards are consistently met.

In summary, the Frymaster H55 is a cutting-edge commercial fryer that embodies efficiency, safety, and innovation. With its advanced filtration system, energy-efficient design, digital controls, and versatility, it is an essential piece of equipment for any high-volume foodservice operation, delivering exceptional frying performance while reducing operational costs.
Top Page Image Contents