Extron electronic DVS 304 AD, DVS 304 D manual Quick Start DVS

Quick Start — DVS 304

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The Class A limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

NThis unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to ensure compliance with FCC emissions limits.

声明

所使用电源为 A 级产品，在生活环境中，该产品可能会造成无线电干扰。在这种情况下，可能需要用户对其干扰采取切实可行的措施。

Installation

Step 1

Refer to the application examples at the end of this section. If connected to a power source, turn off power to the scaler, the input and output­ devices, and remove power cords.

Step 2

Install the four rubber feet on the bottom of the DVS 304 scaler, or mount the scaler in a rack (see chapter 2 “Installation and Operation”).

	RGsB	Component Video (Y, R-Y, B-Y)
R	G	B	R	G	B
/R-Y	/Y	/B-Y	/R-Y	/Y	/B-Y
H/	V		H/	V
HV			HV

RGB

Output 15-pin HD connector

NYou can connect both outputs simultaneously to two different displays. The sync format is the same for both outputs.

Step 3

Attach input devices to the scaler (see chapter 2 “Installation and Operation”).

Step 5 (for DVS 304 A or DVS 304 AD only)

Connect up to four balanced or unbalanced stereo

Rear panel video inputs

SDI input (DVS 304 D or AD models only)

Attach an SDI source to this optional BNC.

SDI

audio input devices to the DVS 304 as shown below. Each audio input has a 3.5 mm, 5-pole captive screw connector.

For detailed wiring instructions, see chapter 2 “Installation and Operation”.

Input 1: Composite video 1						VID
Input 2: Composite/S-video/YUVi/YUVp
Composite Video			S-video (YC)		Component Video (Y, R-Y, B-Y)
	Y	B-Y	Y	B-Y		Y	B-Y
	/VID	/C	/VID	/C		/VID	/C
2	R-Y	2	R-Y		2	R-Y
Input 3: S-video			3	YC

Input 4: Composite/S-video/YUVi/YUVp/RGBcvS/

RGB/R-Y,Y,B-Y/YC/VID

RGB scaled/RGB pass through

4

Step 4

Attach output devices to the scaler.

Balanced and unbalanced audio input

Unbalanced Input	Balanced Input
(high impedance)	(high impedance)

Tip	L R			Tip
Sleeve		AUDIO
				Tip	L R	AUDIO
Sleeve
				Ring
Tip			Sleeves
				Ring
				Do not tin the wires!
Balanced and unbalanced audio output
See Caution Tip		LR	AUDIO	Tip	LR
				Ring
Sleeve (s)				Sleeve (s)
Tip				Tip
See Caution				Ring

Unbalanced Stereo Output Balanced Stereo Output

CAUTION

For unbalanced audio, connect the sleeve(s) to the center contact ground. DO NOT connect the sleeve(s) to the negative (-) contacts.

Rear panel video outputs

Output BNC connectors

	RGBHV			RGBS
R	G	B	R	G	B
					/B-Y
/R-Y	/Y	/B-Y	/R-Y	/Y

Step 6

Plug the DVS 304, and the input and output devices into a grounded AC source, then turn on the input and output devices.

H/	V	H/	V
HV		HV

DVS 304 • Quick Start QS-1