InSinkErator 1100 Care and USE, Factory temperature pre-set is, Disconnect power from unit

Page 12

CARE AND USE

Electric Shock Hazard: To prevent electrical shock, disconnect power before servicing unit. Use only a properly grounded and polarized electric outlet.

ADJUSTING THE THERMOSTAT

Factory temperature pre-set is

approx. 200°

200˚F. To reset the thermostat

 

to 200°, turn the indicator two

 

notches to the right of vertical.

 

■ Adjust the thermostat slowly, turning the dial

clockwise to increase

temperature or counter clockwise to decrease temperature, then activate faucet handle for 20 seconds to bring in fresh water to be heated at the new setting. Allow 5-7 minutes for water to reach new temperature.

Scalding Hazard: Do not allow

water to boil. May result in severe burns.

SEASONAL STORAGE/DRAINAGE

Anytime the instant hot water dispenser is not used for extended periods of time, unplug and drain unit. If it is below freezing you will need to unplug the unit and drain it.

Disconnect power from unit.

Push hot water dispenser faucet lever and allow water to flow until it is cool.

Shut the cold water supply off at the valve.

Locate and remove drain screw from bottom center of water tank and drain the water into empty pail.

Empty the tank and then reinstall drain screw into the bottom of tank, turning until snug. Do NOT over tighten.

Remove and discard filter cartridge.

To put back into working order, install new filter cartridge, fill tank with water and reconnect the electrical cord. (Refer to Page 9, Step 6B)

CLEANING THE FAUCET AND TANK

Only use mild cleaners to clean the faucet and plastic components.

Cleaners with acids, abrasives, alkaline or organic solvents will result in deterioration of the plastic components and void the warranty.

FILTER GUIDE AND REPLACEMENT

Replace filter cartridge when there is an obvious decrease in water flow to the faucet or if there is an objectionable taste or odor to the water.

When the inlet and outlet ports have been closed and the filter’s internal pressure has been relieved, water (about 2 oz) will discharge from vent line.

If the new filter cartridge cannot be inserted, insert the old one and turn until it stops, remove it and then retry the new cartridge.

Carbon filters should be replaced within 12 months.

Filter replacement instructions:

Replace with an InSinkErator® filter.

Place pan or dish towel under the filter to catch water drainage during change.

Slowly turn the cartridge counter-clockwise completely until it stops (1/4 turn).

Pull cartridge straight down and discard.

Insert new cartridge into filter head.

Top surface of cartridge will become flush with the bottom of the filter head when fully engaged.

Turn the cartridge clockwise until it stops (1/4 turn).

Align the in/out arrow on the head and bracket assembly to the in/out arrow on the cartridge.

Open faucet to expel trapped air.

Run water for 3 minutes before usage.

PROPERTY DAMAGE

Regularly inspect the unit for any signs of leakage. If there are signs of water damage, immediately remove the unit from service.

To avoid water damage from leakage, replace all cut, loose or split tubing.

A drain pan, plumbed to an appropriate drain or outfitted with a leak detector, should be used in those applications where any leakage could cause property damage.

12

Image 12
Contents Instant Hot Water Dispenser What YOU should Know Before YOU Begin What YOU Need to GET StartedUnpack dispenser components Straighten the copper tubingComponents in this Package PlugSemi-circular Mounting Plate Hex Tool Filter HeadPreparation 31⁄837⁄8 Installing the Faucet On a firm, flat surface, carefullyStraighten the copper tubing Unpack dispenser componentsConnecting Faucet to Tank Mounting the TankTank a Tank BInstalling Filtration System Screws provided are for use in woodFinal Water Connection Turn on the cold water supplyIf Installing only NEW Faucet If Installing only NEW TankProperty Damage Warranty Information Year warranty excluding replaceable filter cartridgeFactory temperature pre-set is Disconnect power from unitCare and USE Shut the cold water supply off at the valveFiltration Information Troubleshooting Manual del usuario LO QUE Usted Debe Saber Antes DE Comenzar Cómo Usar Este Manual DE Instrucciones Lo que usted verá en el manual de instruccionesContenido DE Este Paquete HexagonalPreparación Mínimo requerido delInstalación DEL Grifo Montaje DEL Tanque Conexión DEL Grifo EN EL TanqueTanque a Tanque BInstalación DEL Filtro Conexión Final DEL Agua El agua saldrá fría en un principioPara Instalar Sólo UN Grifo Nuevo Para Instalar Sólo UN Tanque NuevoInserte el tubo azul dentro del accesorio Del tanqueInformación Sobre LA Garantía Tanques de acero inoxidableExcluyendo el cartucho del filtro reemplazable Mantenimiento Y USO Ajuste DEL Termostato Guía Para EL Filtro Y ReemplazoInformación DE LA Filtración Identificación Y Solución DE Problemas Manuel du propriétaire CE QUE Vous Devriez Savoir Avant DE Commencer Comment Utiliser CE Manuel D’INSTRUCTIONS CuivreDans CET Emballage Préparation GN2215 37⁄8 10 cm HC2200GN2200 37⁄8 10 cm HC1100 GN1100 37⁄8 10 cmInstallation DU Robinet Déballez les composantesDu distributeur Sur une surface plane et fermeMontage DU Réservoir Raccordement DU Robinet AU RéservoirRéservoir a Réservoir BInstallation DU Systéme DE Filtration Ou de pincement du tubeDe cuivre plus loin que les 16 po fournis Connexion Finale DE L’EAU ’eau sera froide au débutBranchez le réservoir d’eau chaude instantanée Dommage matériel Avant de raccorder le robinetNe serrez pas trop l’écrou en laiton Dernier pouce du tubeRenseignements SUR LA Garantie Réservoir en acier inoxydableSoins ET Utilisation Réglage DU ThermostatInformation DE Filtration Diagnostics 800.558.5700

1100 specifications

The InSinkErator 1100 is a popular model among household garbage disposals, celebrated for its robust construction and efficient performance. Ideal for homeowners who prioritize convenience and cleanliness in their kitchens, the 1100 model excels in efficiently disposing of food waste, thus promoting a hygienic cooking environment.

One of the standout features of the InSinkErator 1100 is its powerful grinding capability. Equipped with a 0.75 HP motor, this unit can easily accommodate a wide variety of food scraps, including fibrous vegetables, bones, and even small fruit pits. This high torque ensures that everything is pulverized quickly, allowing for smooth drainage and minimal clogging. Additionally, the grinder operates quietly, thanks to its anti-vibration design, which is a significant advantage in homes with open kitchen layouts.

The InSinkErator 1100 also incorporates advanced technologies to enhance its efficiency and durability. The GrindShield technology is a notable feature, which helps to reduce wear and tear on the grinding components and prolongs the lifespan of the unit. Moreover, the permanently lubricated motor not only ensures a quieter operation but also eliminates the need for routine maintenance, making it a hassle-free choice for users.

Ease of installation is another characteristic that sets the InSinkErator 1100 apart from other models. With a straightforward design and compact size, it easily fits under most kitchen sinks. The unit comes with a comprehensive installation kit, ensuring that homeowners can set it up without professional help, saving both time and money.

In terms of safety, the 1100 model is designed with a manual reset button in case of overload, providing an extra layer of protection against potential hazards. Additionally, its stainless-steel grinding components are resistant to corrosion, ensuring reliable performance and maintenance of hygiene standards over the years.

The InSinkErator 1100 ranks as an excellent choice for those looking to invest in a durable, high-performance garbage disposal system. Its combination of strength, efficiency, and user-friendly features makes it a highly regarded option among homeowners seeking to upgrade their kitchen appliances for improved waste management.