GE Monogram ZDIW50 installation instructions Vacation and Moving, To shut down the icemaker

Page 15

Vacation and Moving

WARNING: Make sure the icemaker is disconnected from the main power supply before removing the lower access panel. Failure to do so could result in electric shock or personal injury.

To shut down the icemaker:

1.Disconnect the electrical power supply to the icemaker and turn the Cycle Control Knob to “OFF.”

2.Remove all ice from the storage bin.

3.Shut off the water supply.

4.Remove the screw from the top of the lower access panel and the two screws from the grille area of the lower access panel, then remove the panel. Pull forward at the bottom, then down.

5.Disconnect the inlet and outlet lines to the water valve. Allow these lines to drain and then reconnect to the valve.

6.Replace the lower access panel and screws. The top of the access panel needs to be secured under the two metal tabs before replacing the screws.

7.Remove water from the drain lines and drain water pan.

8.Before using again, clean the icemaker and storage bin.

NOTE: All components of the icemaker are permanently lubricated at the factory. They should not require any additional oiling throughout the normal life of the machine.

NORMAL		ON
THIN	THICK OFF	CLEAN

ICE

CYCLE

Lower	Screw
Access
Panel

Grille
Area	Screws
Outlet	Inlet
Outlet

Water

Pan

15

Image 15

Contents Monogram.TM Introduction ContentsHelp US Help YOU… If YOU Need ServiceRead All Instructions Before Using This Appliance Important Safety InstructionsHow the Icemaker Works Operating Your IcemakerSetting the Controls Features of Your IcemakerDirty or clogged condenser Care and CleaningCleaning Outside Surfaces Cleaning the CondenserTurn the Cycle Control Knob to OFF Cleaning the Icemaker SystemRemove the hose from the water pump Cleaning the Inside Parts of the IcemakerChanging the Light Bulb Filtering and Treating WaterLeveling PreparationUnpacking the Icemaker LocationTo change the panel Changing the Bin Door PanelChanging the Lower Access Panel Install Custom Door and Access Panels Custom Door and Access PanelsCustom Door and Access Panels-1/4″Thick Custom Door and Access Panels-3/4″ThickTo shut down the icemaker Vacation and MovingRecommended Grounding Methods Free Standing InstallationInstallation Requirements For the InstallerConnect to water. Observe local codes Installation InstructionsDrain Pump QUESTIONS? USE this Problem Solver We’ll Be There Warranty Page Máquina para hacer hielo Contenido IntroducciónSI SE Necesita Servicio Ayudenos a AYUDARLE…Instrucciones DE Seguridad Cómo funciona la máquina para hacer hielo Operacion DE SU Maquina Para Hacer HieloCaracteristicas DE SU Maquina Para Hacer Hielo Ajustando los controlesPase Un condensador sucio o tapado Cuidado Y LimpiezaLimpieza de las superficies exteriores Limpieza del condensadorAgua* y haga girar La perilla de Control De ciclo hasta la Limpieza del sistema de la máquina para hacer hieloVierta 1/2 galón De agua Caliente del grifo En la bandeja paraLimpieza de los componentes interiores Cambio de la bombilla Filtrado y tratamiento del aguaCalibraciones del termostato PreparacionLocalización NivelaciónPara cambiar el panel Cómo cambiar el panel de la puerta del depósitoPuede sufrir un choque eléctrico o lesiones personales Cómo cambiar el panel inferior de accesoPuerta Y Paneles DE Acceso a LA Medida Puerta y paneles de acceso a la medida de 1/4″ de espesorPuerta y paneles de acceso a la medida de 3/4″ de espersor Vacaciones y mudanzas Métodos que se recomiendan para conectar a tierra Instalacion IndependienteInstrucciones Para LA Instalacion Para el instaladorConexión al agua. Respete los códigos locales Cada instalación es individual pero requeriráContinuación Nivelacion¿ALGUNA PREGUNTA? Consulte Estas Soluciones Estaremos Con Usted Garantia Notas