GE Monogram ZDIW50 installation instructions Features of Your Icemaker, Setting the Controls

Page 6

OPERATING YOUR ICEMAKER

(continued)

Setting the Controls

1.Select ice thickness. The icemaker has been preset to produce ice approximately 1/2″ (13 mm) thick, while operating in a room temperature of 70°F.

(21°C.).

Operation in different room temperatures may require readjusting the control toward either the “THICK” or “THIN” setting.

Best operation will be obtained with ice 1/2″ (13 mm) to 5/8″ (16 mm) thick.

If operating in a warm room (above 90°F. [32°C.]) DO NOT set the control to maximum thickness or the icemaker may malfunction.

2.To start the normal icemaking cycle, turn the Cycle Control Knob to “ON.”

3.To stop icemaker operation, turn Cycle Control Knob to “OFF.”

The “CLEAN” setting is used whenever solutions are circulated through the icemaker for cleaning. Only the water pump operates at this setting. See Cleaning the Icemaker System in the Care and Cleaning section for specific instructions.

NORMAL		ON
THIN	THICK OFF	CLEAN

ICE

CYCLE

NORMAL		ON
THIN	THICK OFF	CLEAN

ICE

CYCLE

FEATURES OF YOUR ICEMAKER

	NORMAL		ON
THIN	THICK	OFF	CLEAN

CYCLE

ICE

Model and Serial Number Plate (not shown)

Ice Retainer

Baffle

Lower

Access

Panel

Ice Thickness Knob

Cycle Control Knob

Bin Light

Ice Bin

Ice Scoop

6

Image 6

Contents Monogram.TM Contents IntroductionIf YOU Need Service Help US Help YOU…Important Safety Instructions Read All Instructions Before Using This ApplianceOperating Your Icemaker How the Icemaker WorksFeatures of Your Icemaker Setting the ControlsCleaning the Condenser Care and CleaningCleaning Outside Surfaces Dirty or clogged condenserCleaning the Icemaker System Turn the Cycle Control Knob to OFFCleaning the Inside Parts of the Icemaker Remove the hose from the water pumpFiltering and Treating Water Changing the Light BulbLocation PreparationUnpacking the Icemaker LevelingChanging the Bin Door Panel To change the panelChanging the Lower Access Panel Custom Door and Access Panels-3/4″Thick Custom Door and Access PanelsCustom Door and Access Panels-1/4″Thick Install Custom Door and Access PanelsVacation and Moving To shut down the icemakerFor the Installer Free Standing InstallationInstallation Requirements Recommended Grounding MethodsInstallation Instructions Connect to water. Observe local codesDrain Pump QUESTIONS? USE this Problem Solver We’ll Be There Warranty Page Máquina para hacer hielo Introducción ContenidoAyudenos a AYUDARLE… SI SE Necesita ServicioInstrucciones DE Seguridad Operacion DE SU Maquina Para Hacer Hielo Cómo funciona la máquina para hacer hieloCaracteristicas DE SU Maquina Para Hacer Hielo Ajustando los controlesPase Limpieza del condensador Cuidado Y LimpiezaLimpieza de las superficies exteriores Un condensador sucio o tapadoCaliente del grifo En la bandeja para Limpieza del sistema de la máquina para hacer hieloVierta 1/2 galón De agua Agua* y haga girar La perilla de Control De ciclo hasta laLimpieza de los componentes interiores Filtrado y tratamiento del agua Cambio de la bombillaNivelación PreparacionLocalización Calibraciones del termostatoCómo cambiar el panel de la puerta del depósito Para cambiar el panelCómo cambiar el panel inferior de acceso Puede sufrir un choque eléctrico o lesiones personalesPuerta Y Paneles DE Acceso a LA Medida Puerta y paneles de acceso a la medida de 1/4″ de espesorPuerta y paneles de acceso a la medida de 3/4″ de espersor Vacaciones y mudanzas Para el instalador Instalacion IndependienteInstrucciones Para LA Instalacion Métodos que se recomiendan para conectar a tierraCada instalación es individual pero requerirá Conexión al agua. Respete los códigos localesNivelacion Continuación¿ALGUNA PREGUNTA? Consulte Estas Soluciones Estaremos Con Usted Garantia Notas