GE Monogram ZDIW50 Free Standing Installation, Installation Requirements, For the Installer

Page 16

FREE STANDING INSTALLATION

For the Installer

When this icemaker is installed free standing (not under a counter) we strongly recommend that the bottom rear corners of the icemaker be fastened to the floor to prevent accidental tipping.

INSTALLATION REQUIREMENTS

IMPORTANT…Please Read Carefully

For the Electrician—Electrical Requirements

A 115 Volt, 60 Hz, AC only, 15 Amp fused electrical supply is required (time delay fuse or circuit breaker is recommended). It is recommended that a separate circuit, serving only this appliance, be provided. DO NOT use an extension cord.

ELECTRICAL GROUND IS REQUIRED ON THIS APPLIANCE.

Recommended Grounding Methods

DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE POWER SUPPLY CORD GROUND PRONG.

For your personal safety, this appliance must be properly grounded.

This appliance is equipped with a power supply cord having a 3-prong grounding plug. To minimize possible shock hazard, the cord must be plugged into a mating 3-prong grounding type wall receptacle, grounded in accordance with the National Electrical Code and local codes and ordinances. If a mating wall receptacle is not available, it is the personal responsibility and obligation of the customer to have a properly grounded 3-prong wall receptacle installed by a qualified electrician.

3-Prong Grounding Type Wall Receptacle

3-Prong Grounding Plug

Power Supply

Cord

16

Image 16

Contents Monogram.TM Contents IntroductionIf YOU Need Service Help US Help YOU…Important Safety Instructions Read All Instructions Before Using This ApplianceOperating Your Icemaker How the Icemaker WorksFeatures of Your Icemaker Setting the ControlsCare and Cleaning Cleaning Outside SurfacesCleaning the Condenser Dirty or clogged condenserCleaning the Icemaker System Turn the Cycle Control Knob to OFFCleaning the Inside Parts of the Icemaker Remove the hose from the water pumpFiltering and Treating Water Changing the Light BulbPreparation Unpacking the IcemakerLocation LevelingChanging the Bin Door Panel To change the panelChanging the Lower Access Panel Custom Door and Access Panels Custom Door and Access Panels-1/4″ThickCustom Door and Access Panels-3/4″Thick Install Custom Door and Access PanelsVacation and Moving To shut down the icemakerFree Standing Installation Installation RequirementsFor the Installer Recommended Grounding MethodsInstallation Instructions Connect to water. Observe local codesDrain Pump QUESTIONS? USE this Problem Solver We’ll Be There Warranty Page Máquina para hacer hielo Introducción ContenidoAyudenos a AYUDARLE… SI SE Necesita ServicioInstrucciones DE Seguridad Operacion DE SU Maquina Para Hacer Hielo Cómo funciona la máquina para hacer hieloAjustando los controles Caracteristicas DE SU Maquina Para Hacer HieloPase Cuidado Y Limpieza Limpieza de las superficies exterioresLimpieza del condensador Un condensador sucio o tapadoLimpieza del sistema de la máquina para hacer hielo Vierta 1/2 galón De aguaCaliente del grifo En la bandeja para Agua* y haga girar La perilla de Control De ciclo hasta laLimpieza de los componentes interiores Filtrado y tratamiento del agua Cambio de la bombillaPreparacion LocalizaciónNivelación Calibraciones del termostatoCómo cambiar el panel de la puerta del depósito Para cambiar el panelCómo cambiar el panel inferior de acceso Puede sufrir un choque eléctrico o lesiones personalesPuerta y paneles de acceso a la medida de 1/4″ de espesor Puerta Y Paneles DE Acceso a LA MedidaPuerta y paneles de acceso a la medida de 3/4″ de espersor Vacaciones y mudanzas Instalacion Independiente Instrucciones Para LA InstalacionPara el instalador Métodos que se recomiendan para conectar a tierraCada instalación es individual pero requerirá Conexión al agua. Respete los códigos localesNivelacion Continuación¿ALGUNA PREGUNTA? Consulte Estas Soluciones Estaremos Con Usted Garantia Notas