GE Monogram ZDIW50 Cleaning the Icemaker System, Turn the Cycle Control Knob to OFF

Page 8

CARE AND CLEANING

(continued)

Cleaning the Icemaker System

WARNING: Most ice machine cleaners are citric or phosphoric acid which can cause irritation even after dilution. In

case of contact with eyes, flush eyes thoroughly with fresh water and contact a physician immediately. In case of contact with skin, rinse well with water. If swallowed, give large amounts of water and contact a physician immediately. Do not induce vomiting. KEEP OUT OF REACH OF CHILDREN.

1.Turn the Cycle Control Knob to “OFF.”

Electrical

 

NORMAL

ON

THIN

THICK OFF

CLEAN

Harness

 

ICE

CYCLE

Screws (long)

 

 

2.Remove the two screws and slide the ice cutter grid forward, out of the two slots near the water pan.

3.Unplug the electrical harness.

CAUTION: Any ice on the grid should be melted under running warm water. Attempting to pick the ice slab off the grid may stretch and damage the grid wires.

4.Remove all ice from the storage bin and the freezing plate.

Screws

Drain

Plug

Water Pan

5.Drain the water pan by removing the drain plug and then replace the plug.

NORMAL

 

ON

THIN

THICK OFF

CLEAN

ICE

CYCLE

6.Pour 1/2 gallon (1.9 L) of hot tap water into the water pan* and turn the Cycle Control Knob to “CLEAN.” This warms up the system to make the cleaning solution more effective. Let circulate for five minutes. While tap water is circulating, prepare the cleaning solution. Mix: 6 oz. (170 g) powdered citric or phosphoric acid into 1/2 gallon (1.9 L) hot water. (Citric and phosphoric acid crystals are available or can be ordered from many pharmacies or scientific supply houses.)

Commercial ice machine cleaners (liquid) are also available from your dealer or refrigeration parts supply stores. Mix according to instructions on label (total quantity 1/2 gallon [1.9 L]).

7.Turn the Cycle Control Knob to “OFF” and drain the water pan. (See step 5.)

8.Turn the Cycle Control Knob to “CLEAN” and slowly pour the hot cleaning solution into the water pan.* (If the solution foams while pouring, wait until the foaming stops.) Then add the balance of the solution.

Allow the solution to circulate until the scale has dissolved (15 to 20 minutes). Severe scale build- up may require repeated cleaning with a fresh quantity of cleaning solution.

To clean scale off the side flanges of the freezing plate, use rubber gloves and scrub with a non- abrasive plastic scrubbing pad or nylon brush dipped in cleaning solution.

9.Keep rubber gloves on to drain the cleaning solution. Turn the Cycle Control Knob to “OFF” and drain the water pan. (See step 5.)

10.Replace the plug and add 1/2 gallon (1.9 L) of fresh water.* Set Cycle Control Knob on “CLEAN,” circulate five minutes and drain. Repeat rinsing process.

*For easier pouring of water and cleaning solution, use a 1- or 2-cup container.

8

Image 8
Contents Monogram.TM Contents IntroductionIf YOU Need Service Help US Help YOU…Important Safety Instructions Read All Instructions Before Using This ApplianceOperating Your Icemaker How the Icemaker WorksFeatures of Your Icemaker Setting the ControlsCare and Cleaning Cleaning Outside SurfacesCleaning the Condenser Dirty or clogged condenserCleaning the Icemaker System Turn the Cycle Control Knob to OFFCleaning the Inside Parts of the Icemaker Remove the hose from the water pumpFiltering and Treating Water Changing the Light BulbPreparation Unpacking the IcemakerLocation LevelingChanging the Bin Door Panel To change the panelChanging the Lower Access Panel Custom Door and Access Panels Custom Door and Access Panels-1/4″ThickCustom Door and Access Panels-3/4″Thick Install Custom Door and Access PanelsVacation and Moving To shut down the icemakerFree Standing Installation Installation RequirementsFor the Installer Recommended Grounding MethodsInstallation Instructions Connect to water. Observe local codesDrain Pump QUESTIONS? USE this Problem Solver We’ll Be There Warranty Page Máquina para hacer hielo Introducción ContenidoAyudenos a AYUDARLE… SI SE Necesita ServicioInstrucciones DE Seguridad Operacion DE SU Maquina Para Hacer Hielo Cómo funciona la máquina para hacer hieloPase Caracteristicas DE SU Maquina Para Hacer HieloAjustando los controles Cuidado Y Limpieza Limpieza de las superficies exterioresLimpieza del condensador Un condensador sucio o tapadoLimpieza del sistema de la máquina para hacer hielo Vierta 1/2 galón De aguaCaliente del grifo En la bandeja para Agua* y haga girar La perilla de Control De ciclo hasta laLimpieza de los componentes interiores Filtrado y tratamiento del agua Cambio de la bombillaPreparacion LocalizaciónNivelación Calibraciones del termostatoCómo cambiar el panel de la puerta del depósito Para cambiar el panelCómo cambiar el panel inferior de acceso Puede sufrir un choque eléctrico o lesiones personalesPuerta y paneles de acceso a la medida de 3/4″ de espersor Puerta Y Paneles DE Acceso a LA MedidaPuerta y paneles de acceso a la medida de 1/4″ de espesor Vacaciones y mudanzas Instalacion Independiente Instrucciones Para LA InstalacionPara el instalador Métodos que se recomiendan para conectar a tierraCada instalación es individual pero requerirá Conexión al agua. Respete los códigos localesNivelacion Continuación¿ALGUNA PREGUNTA? Consulte Estas Soluciones Estaremos Con Usted Garantia Notas