Miele G 7883 CD installation instructions Buzzer, Programming functions

Page 39

Buzzer

Programming functions

Buzzer

The buzzer can be programmed for the following functions:

–a continuous tone at the end of a program,

–an error signal that beeps in 1-second intervals, and

–a sample-collection signal (allows a sample of the final rinse water to be collected) that beeps in sets of 3 followed by a 2-sec pause. Contact Miele Technical Service to program the sample-collection

signal.

The numbers shown in the display correspond to the following settings:

20Buzzer off

21End of program (factory setting)

22Error

23End of program + Error

24Sample-collection signal

25End of program + Sample-collection signal

26Error + Sample-collection signal

27All functions (End of program + Error + Sample-collection signal)

Step	Display / Result

^Press the 0 button until E04 appears in the display. E04

^	Turn the program selector to "Inorganica".	21

^ Press and hold the ß button until the required value		26
	appears in the display, e.g., 26.

Value selected:

The buzzer will sound for 30 sec during the selected setting.

To switch it off earlier:

–Turn the program selector to f.

–Press the ß button.

–Interrupt the power supply, e.g., open the door.

39

Image 39

Contents Operating and Installation Instructions Laboratory Glassware Washer G 7883 CDen - US, CA Page Contents Program Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Programming functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 The following instructions apply to all programming functions:. . . . . . . . . . . . . . . 36 To access the programming mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Saving to memory and exiting the programming mode . . . . . . . . . . . . . . . . . . 36 Exiting the programming mode without saving . . . . . . . . . . . . . . . . . . . . . . . . 36 DOS 1 liquid detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Setting the detergent dosage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Priming the dosage system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 DOS 3 neutralizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Setting the neutralizer dosage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Priming the dosage system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Changing program parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Changing the temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Changing the holding time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Restoring the factory settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Setting the time and date. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Resetting the coarse and fine filter timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Data transfer optional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Routine checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Thermo switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 After Sales Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 INSTALLATION INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Plumbing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IMPORTANT SAFETY INSTRUCTIONS ~Take care when handling processing chemicals detergents, softeners, neutralizers, etc.. These may contain irritant or corrosive ingredients. Do not use organic solvents as these could cause an explosion. Wear protective gloves and goggles. With all chemical agents the manufacturer’s safety conditions must be observed IMPORTANT SAFETY INSTRUCTIONS Disposal of an old appliance Please note the following symbols on the machineAccessories SAVE THESE INSTRUCTIONSGuide to the lab washer d Rinse aid reservoir with dosage selector h Service panel i Serial interfacea Drying unit c Dispenser for powdered detergentDescription of the machine Standard modelIntended applications: Laboratory equipment To close the door Opening and closing the doorElectric door lock To open the doorWater softener Setting the water softenerfactory setting SettingsFilling the salt reservoir Salt indicator Adding rinse aid Rinse AidSetting the rinse aid dosage Rinse aid indicator lightAdding neutralizer Neutralizing agentNeutralizer indicator light Setting the liquid detergent dosage DetergentAdding detergent Liquid detergent refill light ^Snap the cover closed ^Load the detergent into the compartmentLoading the machine Loading the machine Prepare items before loadingSpecial preparations before operating the machine Adjusting the upper basket Spring adapter for the water connectionTo adjust the upper basket Laboratory equipment Upper basket O For various insertsLower basket U Upper basket For direct injection of E Injector wagonO Injector wagon For narrow necked glasswareTurning on Starting a programSelecting the optional drying function Program sequence display End of a program Turning offAdditional drying Canceling a program Program Guide Program sequence Saving to memory and exiting the programming mode Programming functionsTo access the programming mode General informationDisplay / Result DOS 1 liquid detergentSetting the detergent dosage StepSetting the neutralizer dosage DOS 3 neutralizerBuzzer Changing program parameters Changing the wash and rinse parametersChanging the drying parameters Changing the holding time Step Changing the temperature StepRestoring the factory settings Setting the time and date Resetting the coarse and fine filter timer Data transfer optional Routine checks MaintenanceCleaning the filters in the wash cabinet Cleaning and CareCleaning the fine, flat and micro-finefilters Removing the spray arms Cleaning the spray armsCleaning the drain pump and non-returnvalve Cleaning the filters Cleaning the water inlet filtersCleaning the door seal Cleaning the control panelCleaning the exterior Cleaning the wash cabinetBaskets and inserts What if Frequently asked questionsPossible fault SolutionWhat if Frequently asked questionsWhat if Frequently asked questionsWhat if Frequently asked questionsWhat if Frequently asked questionsWhat if Items made of stainless Items made of glassshow signs of corrosionThere are white deposits and/or spotson the labware unacceptable The wash result isThermo switch After Sales Service V1-800-565-6435service@miele.caU1-800-991-9380techserv@mieleusa.com INSTALLATION INSTRUCTIONS Installation Leveling the legsPositioning and securing the machine Removing the lid if necessary Protecting the countertopCover plate protects the countertop Electrical connection THIS APPLIANCE MUST BE GROUNDEDGrounding connection Plumbing Connecting the water inletPlease also refer to the installation diagram DI connection unpressurized optional DI Connection pressurizedDrainage Technical data EnglishMetric Caring for the environment Disposal of the packing materialsDisposal of an old appliance Page M.-Nr.07 157 440 / Subject to change without notice /