Miele G 7883 CD installation instructions Data transfer optional

Page 45

Data transfer (optional)

Data transfer (optional)

The machine is equipped with an interface socket so that data can be transferred from Novotronic to a log printer.

Please contact Miele Technical Service to order printer cables.

The serial interface is RS 232 compatible.

Various printer types with Epson-compatible fonts can be used for printing.

Miele Technical Service maintains a list of recommended printers.

Pin assignment 9-pin sub-D connector:

5GND (ground)

3 TXD (send)

1-4-6 (bridge)

7-8 (CTS)

,Printer initialization must only be performed by Miele. Consult Technical Service using the contact information on that back of this manual.

During program operation a protocol is prepared. It can be printed using an external printer.

The protocol contains the following information:

–date and device number

–program start time and name

–rinse blocks used

–dosage system with dosage temperature and target dosage amount

–target values for temperature and holding times

–minimal temperature during the holding time

–all errors (e.g., water supply defect)

–program end time

–warnings, e.g., salt required.

45

Image 45

Contents Operating and Installation Instructions Laboratory Glassware Washer G 7883 CDen - US, CA Page Contents Program Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Programming functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 The following instructions apply to all programming functions:. . . . . . . . . . . . . . . 36 To access the programming mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Saving to memory and exiting the programming mode . . . . . . . . . . . . . . . . . . 36 Exiting the programming mode without saving . . . . . . . . . . . . . . . . . . . . . . . . 36 DOS 1 liquid detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Setting the detergent dosage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Priming the dosage system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 DOS 3 neutralizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Setting the neutralizer dosage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Priming the dosage system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Changing program parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Changing the temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Changing the holding time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Restoring the factory settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Setting the time and date. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Resetting the coarse and fine filter timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Data transfer optional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Routine checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Thermo switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 After Sales Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 INSTALLATION INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Plumbing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IMPORTANT SAFETY INSTRUCTIONS ~Take care when handling processing chemicals detergents, softeners, neutralizers, etc.. These may contain irritant or corrosive ingredients. Do not use organic solvents as these could cause an explosion. Wear protective gloves and goggles. With all chemical agents the manufacturer’s safety conditions must be observed IMPORTANT SAFETY INSTRUCTIONS Accessories Please note the following symbols on the machineSAVE THESE INSTRUCTIONS Disposal of an old applianceGuide to the lab washer a Drying unit h Service panel i Serial interfacec Dispenser for powdered detergent d Rinse aid reservoir with dosage selectorDescription of the machine Standard modelIntended applications: Laboratory equipment Electric door lock Opening and closing the doorTo open the door To close the doorWater softener Setting the water softenerfactory setting SettingsFilling the salt reservoir Salt indicator Adding rinse aid Rinse AidSetting the rinse aid dosage Rinse aid indicator lightAdding neutralizer Neutralizing agentNeutralizer indicator light Setting the liquid detergent dosage DetergentAdding detergent Liquid detergent refill light ^Snap the cover closed ^Load the detergent into the compartmentLoading the machine Loading the machine Prepare items before loadingSpecial preparations before operating the machine Adjusting the upper basket Spring adapter for the water connectionTo adjust the upper basket Laboratory equipment Upper basket O For various insertsLower basket U O Injector wagon E Injector wagonFor narrow necked glassware Upper basket For direct injection ofTurning on Starting a programSelecting the optional drying function Program sequence display End of a program Turning offAdditional drying Canceling a program Program Guide Program sequence To access the programming mode Programming functionsGeneral information Saving to memory and exiting the programming modeSetting the detergent dosage DOS 1 liquid detergentStep Display / ResultSetting the neutralizer dosage DOS 3 neutralizerBuzzer Changing program parameters Changing the wash and rinse parametersChanging the drying parameters Changing the holding time Step Changing the temperature StepRestoring the factory settings Setting the time and date Resetting the coarse and fine filter timer Data transfer optional Routine checks MaintenanceCleaning the filters in the wash cabinet Cleaning and CareCleaning the fine, flat and micro-finefilters Removing the spray arms Cleaning the spray armsCleaning the drain pump and non-returnvalve Cleaning the filters Cleaning the water inlet filtersCleaning the exterior Cleaning the control panelCleaning the wash cabinet Cleaning the door sealBaskets and inserts Possible fault Frequently asked questionsSolution What ifWhat if Frequently asked questionsWhat if Frequently asked questionsWhat if Frequently asked questionsWhat if Frequently asked questionsWhat if show signs of Items made of glasscorrosion Items made of stainlessThere are white deposits and/or spotson the labware unacceptable The wash result isThermo switch After Sales Service V1-800-565-6435service@miele.caU1-800-991-9380techserv@mieleusa.com INSTALLATION INSTRUCTIONS Installation Leveling the legsPositioning and securing the machine Removing the lid if necessary Protecting the countertopCover plate protects the countertop Electrical connection THIS APPLIANCE MUST BE GROUNDEDGrounding connection Plumbing Connecting the water inletPlease also refer to the installation diagram DI connection unpressurized optional DI Connection pressurizedDrainage Technical data EnglishMetric Caring for the environment Disposal of the packing materialsDisposal of an old appliance Page M.-Nr.07 157 440 / Subject to change without notice /