Miele G 7883 CD installation instructions Plumbing, Connecting the water inlet

Page 69

Plumbing

Plumbing

Connecting the water inlet

,The water in the machine is not drinkable.

–The machine must be connected to the water supply in accordance with local and national regulations.

–The washer is constructed so it may be connected to a suitable supply without an extra non-return valve unless required by code.

–High iron content can leave a rust film on stainless steel labware and the machine itself.

When the chloride content in the domestic water supply is above 100mg/l, the risk of corrosion damage to stainless steel labware is greatly increased.

–In certain regions (e.g., mountainous areas) the water composition may cause condensate to form, requiring the use of softened water in the steam condenser.

–An acceptable water pressure (flow rate) is 10 - 147 psi. However, the recommended pressure is

25 - 60 psi.

If the water pressure is below 30 psi, the fill time will take longer.

If the "Fill/Drain" indicator fault code "F..E" lights, contact the Miele Technical Service Department.

–The maximum permissible static water pressure is 145 psi over pressure.

–If the water pressure lies outside these ranges, please contact Miele Technical Service for advice (the "Fill/Drain" indicator, may appear in the display "F E").

–The machine is designed for connection to cold water (blue marking) and hot water (red marking) up to 158°F (70°C) max.

Connect the water intake hoses to the cold and hot water faucets.

–If there is no hot water supply, the intake hose with the red marking must also be connected to the cold water supply.

69

Image 69

Contents Operating and Installation Instructions Laboratory Glassware Washer G 7883 CDen - US, CA Page Contents Program Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Programming functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 The following instructions apply to all programming functions:. . . . . . . . . . . . . . . 36 To access the programming mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Saving to memory and exiting the programming mode . . . . . . . . . . . . . . . . . . 36 Exiting the programming mode without saving . . . . . . . . . . . . . . . . . . . . . . . . 36 DOS 1 liquid detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Setting the detergent dosage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Priming the dosage system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 DOS 3 neutralizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Setting the neutralizer dosage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Priming the dosage system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Changing program parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Changing the temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Changing the holding time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Restoring the factory settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Setting the time and date. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Resetting the coarse and fine filter timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Data transfer optional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Routine checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Thermo switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 After Sales Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 INSTALLATION INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Plumbing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IMPORTANT SAFETY INSTRUCTIONS ~Take care when handling processing chemicals detergents, softeners, neutralizers, etc.. These may contain irritant or corrosive ingredients. Do not use organic solvents as these could cause an explosion. Wear protective gloves and goggles. With all chemical agents the manufacturer’s safety conditions must be observed IMPORTANT SAFETY INSTRUCTIONS Accessories Please note the following symbols on the machineSAVE THESE INSTRUCTIONS Disposal of an old applianceGuide to the lab washer a Drying unit h Service panel i Serial interfacec Dispenser for powdered detergent d Rinse aid reservoir with dosage selectorDescription of the machine Standard modelIntended applications: Laboratory equipment Electric door lock Opening and closing the doorTo open the door To close the doorWater softener Setting the water softenerfactory setting SettingsFilling the salt reservoir Salt indicator Adding rinse aid Rinse AidSetting the rinse aid dosage Rinse aid indicator lightAdding neutralizer Neutralizing agentNeutralizer indicator light Setting the liquid detergent dosage DetergentAdding detergent Liquid detergent refill light ^Snap the cover closed ^Load the detergent into the compartmentLoading the machine Loading the machine Prepare items before loadingSpecial preparations before operating the machine Adjusting the upper basket Spring adapter for the water connectionTo adjust the upper basket Laboratory equipment Upper basket O For various insertsLower basket U O Injector wagon E Injector wagonFor narrow necked glassware Upper basket For direct injection ofTurning on Starting a programSelecting the optional drying function Program sequence display End of a program Turning offAdditional drying Canceling a program Program Guide Program sequence To access the programming mode Programming functionsGeneral information Saving to memory and exiting the programming modeSetting the detergent dosage DOS 1 liquid detergentStep Display / ResultSetting the neutralizer dosage DOS 3 neutralizerBuzzer Changing program parameters Changing the wash and rinse parametersChanging the drying parameters Changing the holding time Step Changing the temperature StepRestoring the factory settings Setting the time and date Resetting the coarse and fine filter timer Data transfer optional Routine checks MaintenanceCleaning the filters in the wash cabinet Cleaning and CareCleaning the fine, flat and micro-finefilters Removing the spray arms Cleaning the spray armsCleaning the drain pump and non-returnvalve Cleaning the filters Cleaning the water inlet filtersCleaning the exterior Cleaning the control panelCleaning the wash cabinet Cleaning the door sealBaskets and inserts Possible fault Frequently asked questionsSolution What ifWhat if Frequently asked questionsWhat if Frequently asked questionsWhat if Frequently asked questionsWhat if Frequently asked questionsWhat if show signs of Items made of glasscorrosion Items made of stainlessThere are white deposits and/or spotson the labware unacceptable The wash result isThermo switch After Sales Service V1-800-565-6435service@miele.caU1-800-991-9380techserv@mieleusa.com INSTALLATION INSTRUCTIONS Installation Leveling the legsPositioning and securing the machine Removing the lid if necessary Protecting the countertopCover plate protects the countertop Electrical connection THIS APPLIANCE MUST BE GROUNDEDGrounding connection Plumbing Connecting the water inletPlease also refer to the installation diagram DI connection unpressurized optional DI Connection pressurizedDrainage Technical data EnglishMetric Caring for the environment Disposal of the packing materialsDisposal of an old appliance Page M.-Nr.07 157 440 / Subject to change without notice /