Miele G 7883 CD Frequently asked questions, What if, Possible fault, Solution, start, continue

Page 54

Frequently asked questions

Frequently asked questions

The following guide can be used to help address minor problems without a service call.

,Repairs should only be performed by Miele Technical Service. Work performed by unqualified persons can place the user at considerable risk of harm.

To help avoid unnecessary service calls, please be sure to check first whether an error message is due to operator error.

To do so:

^Turn the program selector to f. The error message is erased.

^Press the On-Offbutton to switch off the machine.

^Turn the machine back on and re-start the program.

^If the error occurs again and cannot be corrected, contact Miele Technical Service for assistance.

^You will need to provide the error code ( "F...") .

What if...	Possible fault	Solution
The washer will not	The door is not properly	Close the door firmly.
start.	closed.
	The machine is not	Plug in the power cord.
	plugged in.
	The fuses are defective or	Make sure the breaker has
	the circuit breaker has	not tripped.
	tripped.
	The washer is not turned	Press the On-Offbutton
	on.	and select a program.
The program does not	Error message: F 04 - F	Contact Miele Technical
continue.	17, F 20 - F 26, F 28 -	Service.
	F - -
	Fault code F 31 - 33	Dosing system faulty.
		Contact Miele Technical
		Service.

54

Image 54

Contents Operating and Installation Instructions Laboratory Glassware Washer G 7883 CDen - US, CA Page Contents Program Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Programming functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 The following instructions apply to all programming functions:. . . . . . . . . . . . . . . 36 To access the programming mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Saving to memory and exiting the programming mode . . . . . . . . . . . . . . . . . . 36 Exiting the programming mode without saving . . . . . . . . . . . . . . . . . . . . . . . . 36 DOS 1 liquid detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Setting the detergent dosage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Priming the dosage system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 DOS 3 neutralizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Setting the neutralizer dosage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Priming the dosage system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Changing program parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Changing the temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Changing the holding time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Restoring the factory settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Setting the time and date. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Resetting the coarse and fine filter timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Data transfer optional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Routine checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Thermo switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 After Sales Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 INSTALLATION INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Plumbing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IMPORTANT SAFETY INSTRUCTIONS ~Take care when handling processing chemicals detergents, softeners, neutralizers, etc.. These may contain irritant or corrosive ingredients. Do not use organic solvents as these could cause an explosion. Wear protective gloves and goggles. With all chemical agents the manufacturer’s safety conditions must be observed IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS Please note the following symbols on the machineAccessories Disposal of an old applianceGuide to the lab washer c Dispenser for powdered detergent h Service panel i Serial interfacea Drying unit d Rinse aid reservoir with dosage selectorDescription of the machine Standard modelIntended applications: Laboratory equipment To open the door Opening and closing the doorElectric door lock To close the doorSetting the water softener Water softenerSettings factory settingFilling the salt reservoir Salt indicator Rinse Aid Adding rinse aidRinse aid indicator light Setting the rinse aid dosageNeutralizing agent Adding neutralizerNeutralizer indicator light Setting the liquid detergent dosage DetergentAdding detergent Liquid detergent refill light ^Load the detergent into the compartment ^Snap the cover closedLoading the machine Loading the machine Prepare items before loadingSpecial preparations before operating the machine Adjusting the upper basket Spring adapter for the water connectionTo adjust the upper basket Laboratory equipment Upper basket O For various insertsLower basket U For narrow necked glassware E Injector wagonO Injector wagon Upper basket For direct injection ofTurning on Starting a programSelecting the optional drying function Program sequence display End of a program Turning offAdditional drying Canceling a program Program Guide Program sequence General information Programming functionsTo access the programming mode Saving to memory and exiting the programming modeStep DOS 1 liquid detergentSetting the detergent dosage Display / ResultDOS 3 neutralizer Setting the neutralizer dosageBuzzer Changing program parameters Changing the wash and rinse parametersChanging the drying parameters Changing the temperature Step Changing the holding time StepRestoring the factory settings Setting the time and date Resetting the coarse and fine filter timer Data transfer optional Maintenance Routine checksCleaning and Care Cleaning the filters in the wash cabinetCleaning the fine, flat and micro-finefilters Cleaning the spray arms Removing the spray armsCleaning the drain pump and non-returnvalve Cleaning the water inlet filters Cleaning the filtersCleaning the wash cabinet Cleaning the control panelCleaning the exterior Cleaning the door sealBaskets and inserts Solution Frequently asked questionsPossible fault What ifFrequently asked questions What ifFrequently asked questions What ifFrequently asked questions What ifFrequently asked questions What ifFrequently asked questions corrosion Items made of glassshow signs of Items made of stainlessThere are white deposits and/or spotson the labware The wash result is unacceptableThermo switch After Sales Service V1-800-565-6435service@miele.caU1-800-991-9380techserv@mieleusa.com INSTALLATION INSTRUCTIONS Installation Leveling the legsPositioning and securing the machine Removing the lid if necessary Protecting the countertopCover plate protects the countertop Electrical connection THIS APPLIANCE MUST BE GROUNDEDGrounding connection Connecting the water inlet PlumbingPlease also refer to the installation diagram DI Connection pressurized DI connection unpressurized optionalDrainage Technical data EnglishMetric Caring for the environment Disposal of the packing materialsDisposal of an old appliance Page Subject to change without notice / M.-Nr.07 157 440 /